diff --git a/en_US.ISO8859-1/articles/console-server/article.sgml b/en_US.ISO8859-1/articles/console-server/article.sgml index fd85840f76..8cf5c909aa 100644 --- a/en_US.ISO8859-1/articles/console-server/article.sgml +++ b/en_US.ISO8859-1/articles/console-server/article.sgml @@ -1,1231 +1,1231 @@ Console Server

Console Server

The Problem

You have a computer room with lots of Unix server machines and lots of comms hardware. Each of these machines needs a serial console. But serial terminals are hard to find and quite expensive (especially compared to a much more capable PC). And they take up a lot of precious space in the computer room.

You need access to the console because when things break, that is where error messages go. And some tasks have to be done on the console (e.g. boot problems or OS installs/upgrades). Some Unix systems allow the console to break out to the ROM monitor which can sometimes be the only way to unstick a hung machine. This is often done with a LINE BREAK sent on the console serial port.

If we are going to play about with consoles, then there are a couple of other things that would be great:

Possible Solutions

If you use PC hardware for your servers, then a so-called "KVM switch" is one possible solution. This allows the use of a single Keyboard, Video screen and Mouse for multiple boxes. This cuts down on the space problem, but only works for PC hardware (not any comms gear you might have), and is not accessible from outside the computer room. Nor does it have much scroll-back or logging, and you have to handle alerting some other way. The big downside is that it will not work for serial-only devices, such as communications hardware. This means that even with a room full of PC-based servers, you are probably still going to need some sort of serial console solution. [Actually, Doug Schache has pointed out that you can get KVM switches that also do serial consoles or Sun-compatible KVM switching as well as PCs, but they are expensive. See Avocent for example.]

You might be tempted to do without a console terminal, but when things go pear-shaped you really need to see what is on the console. And you have to use the console to boot the machine and do things like OS upgrades or installs.

You might try having a single console terminal and switching from server to server as needed, either with a serial switch or just by patching it into the required machine. Serial switches are also hard to come by and not cheap, and may cause problems with sending BREAK when they switch. And (if your computer room is anything like ours) you never seem to have the right combination of patch leads to connect to the machine you need to, and even if the leads are there you can never work out exactly which combination of DTE/DCE headshells goes with which lead goes with which hardware. So you spend the first 10 minutes fooling around with breakout boxes and a box of leads, all while the server is down and the users are screaming. Of course this does not deal with the logging or remote access requirements. And inevitably the console is not switched to the machine you need so you lose all the console messages that might tell you what is going on.

One popular solution is to use terminal server hardware. Typically, the serial ports are connected to the various machine consoles, and set up for "reverse telnet" access. This means a user can telnet to a given IP/port and be connected to the appropriate console. This can be very cost-effective, as suitable old terminal servers can be picked up fairly cheaply (assuming you do not have a couple lying around). And it is of course network-accessible so suitable for remote access. But it suffers from one major drawback: if the network is down, then you have no access to any console, even if you are standing right next to the machine. (This may be partially alleviated by having a suitable terminal connected to one of the terminal server ports and connecting from there, but the terminal server software may not support that.) Also there is no logging or replay of console messages. But with a bit of work, and the addition of some software such as conserver (described below), this can be made to work pretty well.

A possibility suggested by Bron Gondwana is similar to the above solution. If you use servers with multiple serial ports, you can connect each spare serial port to the console port of the "next" server, creating a ring of console connections (in some sort of order). This can be made to work reasonably well with the aid of the conserver software, but can be a bit confusing otherwise (i.e. remembering which port is connected to which console). And you are stuck if you need to use serial ports for other things (such as modems) or you have machines without spare ports.

Or, if your budget exceeds your willingness to hack, you can buy an off-the-shelf solution. These vary in price and capability. See, for example, Lightwave, Perle, Avocent or Black Box. These solutions can be quite expensive - typically $USD100 - $USD400 per port.

Our Solution

In light of the above requirements, we chose a solution based on a dedicated PC running Unix with a multiport serial card, and some software designed to handle serial consoles.

It includes the following elements:

This design covers all the major requirements except remote power cycling:

Setting Up The Server

Patching the Stallion driver

The only hitch with setting up the server PC is getting the device drivers for the Stallion card. FreeBSD has supported Stallion ISA cards for many years, but unfortunately the driver has not been actively maintained for some years, and does not support the newer Stallion cards (such as the EasyIO-PCI card or some of the other ISA cards with newer UART chips). I have put together a patch file for FreeBSD 4.3 (based on the work of many other people) that will update the system to support these newer cards. Hopefully, this patch will be committed to the FreeBSD tree in time for the 4.4 release. If you are running FreeBSD 4 from prior to this time, you will need to download and apply this patch (instructions are included at the top of the patch file). If you are running FreeBSD 3, then you had probably best upgrade.

Configuring a new kernel

The Stallion driver is not included in the default GENERIC kernel, so you will need to create a kernel config file with the appropriate entries. See the stl(4) man page and the appropriate section of the FreeBSD Handbook.

Building World

After applying the patch you will certainly need to update the whole system, including all the user programs and the kernel. See the documentation in /usr/src/UPDATING and the - FreeBSD + FreeBSD Handbook.

Making The Devices

You will need to make the device notes for the Stallion card (which are not made by default). A new version of /dev/MAKEDEV with Stallion support will have been created by the mergemaster run during the above procedure. If you have a Stallion card with more than 8 ports, then you will need to edit /dev/MAKEDEV and change the definition of maxport at about line 250. By default, MAKEDEV only makes device nodes for 8 ports to keep the size of the /dev directory down.

Run a command like

 	cd /dev/ && sh MAKEDEV cuaE0

to create dial-out devices for the first Stallion card. See the comments in MAKEDEV and the stl(4) man page for more details.

Compiling conserver

(See the section on Conserver versions below; the version I use is not the one available in the FreeBSD ports collection.)

There are two ways to install conserver. You can either compile from the source or use the FreeBSD ports framework.

Using the port framework

Using the ports framework is a bit cleaner, as the package system can then keep track of installed software and cleanly delete them when not being used. Download the port framework from here, unpack it to create a directory called conserver-port. CD to that directory and (as root) type

 	make DEFAULTHOST=consolehost install

where consolehost is the name of the machine running the console server. Specifying this when the binary is compiled will avoid having to either specify it each time the program is run on remote hosts or having to maintain a conserver.cf file on every host. This command will fetch, patch, configure, compile and install the conserver application.

You can then run make package to create a binary package that can be installed on all the other FreeBSD hosts with the pkg_add command. For extra style points, you can make a two versions of the package: one for the console server machine without a DEFAULTHOST argument, and one for all the other hosts with a DEFAULTHOST argument. This will mean the console client program on the console server machine will default to localhost, which will work in the absence of name servers when the network is busted, and also allow "trusted" (i.e. no password required) connections via the localhost IP address for users logged into the console server machine (either via the console screen or the emergency backup modem). The version for the other machines with a DEFAULTHOST argument means users can just use the console client without specifying a hostname every time, and without needing to configure the conserver.cf file on every machine.

From the source tarball

If you prefer, you can download conserver and compile it yourself. You might need to do this if you want to install the console client on non-FreeBSD systems. We run the client on our Solaris hosts and it inter-operates with the FreeBSD-hosted server with no problems. This allows anyone in the whole company (many of whom have PCs and no FreeBSD host access on their desk) to access the console server.

Download the file from the conserver.com FTP site. Extract it into a handy directory then configure it by running

 	./configure --with-master=consoleserver --with-port=782

The --with-master argument avoids having to specify the master server every time the client is run remotely (or keeping up-to-date config files on all remote hosts). The --with-port argument avoids having to update /etc/services on every machine.

Then type make and, as root, make install.

Configuring conserver

The conserver program is configured via a file called conserver.cf. This file usually lives in /usr/local/etc and is documented in the conserver.cf(5) man page.

Our config file looks like this:

 LOGDIR=/var/log/consoles
 gallows:/dev/cuaE0:9600p:&:
 roo:/dev/cuaE1:9600p:&:
 kanga:/dev/cuaE2:9600p:&:
 %%
 allow:  itga.com.au
 trusted:        127.0.0.1 buzz

The first line means all the console log files by default go into the directory /var/log/consoles/. The & in each line says the log file for that machine will be /var/log/consoles/machine.

The next three lines show three machines to which we need to connect. We use the cuaEx devices rather than the ttyEx devices because console ports typically do not show carrier. This means that opening ttyEx would hang and conserver would never connect. Using the cuaEx device avoids this problem. Another solution would be to use the ttyEx devices and enable soft carrier on these ports, perhaps by setting this using the ttyiEx device in the /etc/rc.serial file. See the comments in this file for more details. Also see the sio(4) man page for information on the initial-state and locked-state devices. (The Stallion driver also supports these conventions). And see the stty(1) man page for details on setting device modes.

The last section shows that any user logged into the server machine has passwordless access to all consoles. We do this because there are no user accounts on this machine and it is safely isolated from the wide world behind our firewall. The allow line allows anyone on a machine inside our organisation to access the console server if they provide their password, which is recorded in the conserver.passwd file (see next section).

Setting conserver passwords

The conserver.passwd file contains the encrypted version of the password that each user. The file is documented in the conserver.cf(5) man page.

The only tricky bit is loading the file with encoded passwords. It appeared in FreeBSD that was is no obvious way to generate an encrypted password for inclusion in another file (but see below). So I put together a quick hack perl script to do this:

;
 `stty echo`;
 chop($cleartext);
 print crypt($cleartext, $salt), "\n";
 ]]>

(Note that this uses the FreeBSD MD5-style encrypted passwords. Running this on other Unix variants, or on FreeBSD with DES passwords, will likely need a different style of salt.)

Kris Kennaway has since pointed out you can get the same effect using the openssl passwd command:

 $ openssl passwd -1 
 Password: <password>
 $1$VTd27V2G$eFu23iHpLvCBM5nQtNlKj/
 $

Starting conserver at system boot time

There are two ways this can be done. Firstly, you could start up conserver from init by including an entry in /etc/ttys that looks a bit like this:

 cuaE0	"/usr/local/sbin/conserver"	unknown	on	insecure

This has two advantages: init will restart the master console server if it ever crashes for any reason (but we have not noticed any crashes so far), and it arranges for STDOUT of the conserver process to be directed to the named tty (in this case cuaE0). This is useful because you can plug a terminal into this port, and the conserver program will show all console output not otherwise captured by a client console connection. This is useful as a general monitoring tool to see if anything is going on. We set this terminal up in the computer room but visible from the main office. It is a very handy feature. The downside of running conserver from the ttys file is that it cannot run in daemon mode (else init would continually restart it). This means conserver will not write a PID file, which makes it hard to rotate the log files.

So we start conserver from an rc.d script. If you installed conserver via the port, there will be a conserver.sh.sample file installed in /usr/local/etc/rc.d. Copy and/or rename this to conserver.sh to enable conserver to start at boot time.

In fact we use a modified version of this script which also connects conserver to a terminal via a tty device so we can monitor unwatched console output. Our conserver.sh script looks like this:

 #!/bin/sh
 #
 # Startup for conserver
 #
 
 PATH=/usr/bin:/usr/local/bin
 
 case "$1" in
         'start')
                 TTY=/dev/cuaE7
                 conserver -d > $TTY
                 # get NL->CR+NL mapping so msgs look right
                 stty < /dev/cuaE7 opost onlcr
 		echo -n ' conserver'
                 ;;
 
         'stop')
 		kill `cat /var/run/conserver.pid` && echo -n ' conserver'
                 ;;
 
         *)
                 echo "Usage: $0 { start | stop }"
                 ;;
 
 esac
 exit 0

(Note the use of cuaE0 device and the need to set TTY modes for proper NL->CR handling).

Keeping the log files trimmed

FreeBSD has a program called newsyslog that will automatically handle log file trimming. Just add some lines to the configuration file /etc/newsyslog.conf for the console logs:

 #
 # The log files from conserver
 /var/log/consoles/gallows	644  10    1000 *     Z /var/run/conserver.pid
 /var/log/consoles/kanga		644  10    1000 *     Z /var/run/conserver.pid
 /var/log/consoles/roo		644  10    1000 *     Z /var/run/conserver.pid

This tells newsyslog (which is run from cron every hour on the hour) that the console log files should be archived and compressed once they reach 1Mb, that we should keep 10 of them, and that to signal the server program you send a SIGHUP to the process whose PID is in the conserver.pid file. This is the master server, and it will arrange to signal all the child processes. Yes, this will send a HUP to all clients whenever a single log file needs rotating, but that is quite cheap. See the newsysylog(8) man page for details.

Cabling

This is always the hardest part of this kind of problem!! We had only a dozen or so cables/headshells to build, and we already had a collection of the appropriate crimping tools and hardware, so we did it ourselves. But if you are not set up for this, or you have a large number of cables to make, then you might consider getting some cables custom made. Look in the yellow pages, there are a surprising number of places that do this! Getting custom-made cabling is good, and you can get much more professional results, but can be expensive. For example, the RJ-45 to DB-25 adapter kits described below are about $10 each; custom-made headshells are about twice that (and take a couple of weeks to arrive). Similarly, crimping custom RJ-45 to RJ-45 leads is quite cheap (say, $5 each) but it takes a fair amount of time. Custom made RJ-45 socket to RJ-45 plug converters cost about $25 each.

We have settled on RJ-45 Cat-V cabling for all our office and computer room cabling needs. This included patching between racks in the computer room. For serial connections, we use patchable headshells that have RJ-45 sockets on the back. This allows us to patch whatever RJ-45 - DB-25 connections we need.

Which is just as well, because there are many incompatible ways to represent serial connections on the RJ-45 plug. So the cabling has to be very careful to use the right mapping.

RJ-45 colors

RJ-45 cables and plugs have 8 pins/conductors. These are used as 4 matched pairs. There are a couple of conventions about how the pairs are mapped onto pins, but 100baseT uses the most common (known as EIA 586B). There are three common color-coding conventions for the individual conductors in RJ-45 cables. They are:

Pin Scheme 1 Scheme 2 (EIA 568B) Scheme 3 (EIA 568A) Pair
1 Blue White+Green White+Orange 2+
2 Orange Green Orange 2-
3 Black White+Orange White+Green 3+
4 Red Blue Blue 1+
5 Green White+Blue White+Blue 1-
6 Yellow Orange Green 3-
7 Brown White+Brown White+Brown 4+
8 White
or Grey		 Brown Brown 4-

Note EIA 468A and EIA 568B are very similar, simply swapping the colors assigned to pair 2 and pair 3.

See for example the Cabletron Tech Support Site for more details.

The pins in the RJ-45 plug are numbered from 1 to 8. Holding a patch lead with the cable pointing down and the clip away from you, pin 1 is at the left. Or, looking into an RJ-45 socket with the clip to the top, pin 1 is on the right. The following illustration (shamelessly lifted from the Cabletron web site above) shows it pretty well:

RJ45

We have four classes of equipment to deal with in our setup:

Sun Servers

Sun servers operate as DTE (i.e. send data on TxD and read RxD, and assert DTR) with a female DB-25 socket on board. So we need to create a headshell for the Stallion that operates as DCE and has a male DB-25 plug (i.e. acts as a null modem cable as well as converts from RJ-45 to DB-25). We use headshells that have an RJ-45 socket in them and 8 short flyleads with DB-25 pins on the end. These pins can be inserted into the DB-25 plug as required. This allows us to create a custom RJ-45-DB-25 mapping. We used a couple of different sorts, including the MOD-TAP part no. 06-9888-999-00 and the FA730 series from Black Box.

On our version of the headshells, these flyleads had the following colours (from Pin 1-8): Blue, Orange, Black, Red, Green, Yellow, Brown, White. (Looking into an RJ-45 socket, with the clip towards the top, pin 1 is on the right.) This is how they are connected to the DB-25 socket:

Stallion RJ-45 Pin Colour Signal Sun DB-25 Male Pin RS232 Signal
1 Blue DCD 20 DTR
2 Orange RTS 5 CTS
3 Black Chassis Gnd 1 Chassis Gnd
4 Red TxD 3 RxD
5 Green RxD 2 TxD
6 Yellow Signal Gnd 7 Signal Gnd
7 Brown CTS 4 RTS
8 White RTS 8 DCD

Note that colours may be different for your cables/headshells. In particular, pin 8 may be grey instead of white.

Remember to label the headshell clearly, in a way that will not fade/fall off/rub off with time!

Cisco 16xx/26xx/36xx Routers

I think that all Cisco gear that has RJ-45 console ports and runs IOS will have the same cable requirements. But best to check first. We have tried this on 1600s and 2600s only.

Both the Stallion card and the 2600 have RJ-45 connections, but of course they are not compatible. So you need to crimp up a special RJ-45-RJ-45 cable. And this cable must be plugged in the right way round! We use normal RJ-45 flyleads from the router to the patch panel, then the special flylead from the patch panel to the Stallion card.

We built two special Stallion-Cisco leads by cutting in half a 2m flylead and crimping an RJ-45 with the appropriate pinouts to each free end. The original connector will be the Cisco end of the cable, the new crimped connector will be the Stallion end. Holding the RJ-45 connector on the flylead with the cable pointing down and the clip pointing away, this is the order of the colours of the cables in our flylead (pins 1-8, from L to R): white/green, green, white/orange, blue, white/blue, orange, white/brown, brown. For the Stallion end, trim and discard the brown/white+brown and green/white+green pairs. Then holding the RJ-45 plug in the same manner (cable down, clip away), the connections should be (from L to R): None, None, Blue, Orange, White/Orange, White/Blue, None, None, as shown:

Cisco RJ-45 PinColourCisco SignalStallion RJ-45 PinStallion Signal
1White/GreenRTSN/C 
2GreenDTRN/C 
3White/OrangeTxD5RxD
4BlueGnd3Gnd
5White/BlueGnd6Gnd
6OrangeRxD4TxD
7White/BrownDSRN/C 
8BrownCTSN/C 

Note again that colours may be different for your cables/headshells.

Carefully label the cable, and each end of the cable, and test it. If it does not work, testing is really hard as they do not make RJ-45 serial line testers!

Let me state this more stongly: Be very VERY sure that you label this cable in a way that is easily, instantly and permanently recognisable as a special cable and not easily confused with normal drop cables. Some suggestions (from Hugh Irvine):

Cisco Catalyst switches
Astoundingly, the pinout on the console ports of the Catalysts is actually different to the pinout used on the 26xx-series Cisco hardware. I think the way to tell which is which is by considering the operating software. If it uses IOS, then the previous pinout is required. If it uses the switch software, then this pinout is required.

Fortunately, while the pinouts are different, the Catalyst pinout is simply a mirror image of the pinout for the 2600. Even more fortunately, the Ciscos (both Catalysts and 2600s) seem to ship with a special "rollover" cable, which is exactly what is required in this case. We use the rollover cable from the Catalysts to the patch panel, then the same cable as above for the 2600s from the patch panel to the Stallion card, and it all works just fine.

This rollover cable is an RJ-45-RJ-45 cable and is intended to be used with the shipped (hardwired) RJ-45 - DB-25 and RJ-45 - DB-9 headshells for console connections. Ours are 2m long, either light blue or black, and are quite flat. Attempts to use them for 100baseT ethernet will fail miserably! You can tell it is a rollover cable by holding both ends with the cable pointing down and the clip pointing away from you. Check the colour of the leads in each pin in the two connectors, they should be mirror images. (In our case, one goes grey-orange-black-red-green-yellow-blue-brown, the other brown-blue-yellow-green-red-black-orange-grey). This is a rollover cable.

If you do not have a rollover cable present, then you can use the same cable as for the 26xx except plug it in the other way around (i.e. original 8-pin plug goes into the Stallion, the new crimped plug with only 4 active wires goes into the Catalyst).

FreeBSD Servers (or any other i386 PC systems using a serial console)

We run FreeBSD 4 on a couple of i386 PCs for various peripheral uses. FreeBSD usually uses a screen and keyboard for the console, but can be configured to use a serial port (usually the first serial port known as COM1 in DOS/Windows or ttyd0 in Unix).

The cabling for these servers depends on the PC harware. If the PC has DB-25 female socket on board (as most older PCs do), then the same headshell as works for the Sun server above will work fine. If the PC has DB-9 male plug on board (as more recent PCs tend to do), then there are two choices. Either use a DB-9 to DB-25 converter (this is not recommended as it can lead to unreliable connections over the long term as the adapter is bumped/works loose), or build an RJ-45 to DB-9 cable as follows:

Stallion RJ-45 PinColourSignalPC DB-9 Female PinRS232 Signal
1BlueDCD4DTR
2OrangeRTS8CTS
3BlackChassis GndN/C 
4RedTxD2RxD
5GreenRxD3TxD
6YellowSignal Gnd5Signal Gnd
7BrownCTS7RTS
8WhiteRTS1DCD
See below for tips on configuring FreeBSD to use a serial console.

On Sun Systems And Break

Anyone who has turned off a terminal used as a console for a Sun system will know what happens and why this is a problem. Sun hardware recognises a serial BREAK as a command to halt the OS and return to the ROM monitor prompt. A serial BREAK is an out-of-band signal on an RS-232 serial port that involves making the TX DATA line active (i.e. pulled down to less than -5v) for more than two whole character times (or about 2ms on a 9600bps line). Alas, this BREAK signal is all to easily generated by serial hardware during power-on or power-off. And the Stallion card does, in fact, generate breaks when the power to the PC fails. Unless fixed, this problem would mean that every Sun box connected to the console server would be halted whenever the power failed (due to dead power supplies, or fat-fingered operators unplugging it, or whatever). This is clearly not an acceptable situation.

Fortunately, Sun have come up with a set of fixes for this. For Solaris 2.6 and later (and perhaps earlier, but who was crazy enough to run 2.5??), the kbd(1) command can be used to disable the ROM-on-BREAK behaviour. This is a good start, but leaves you out of luck in the situation where a break is needed to get into a broken machine.

Starting with Solaris 8, the kbd command can also be used to enable an alternate break sequence using the kbd -a alternate command. When this is set, the key sequence <Return><Tilda><control-B> (within 5 seconds) will drop to the ROM. You can enable this permanently by editing the /etc/default/kbd file; see the kbd(1) man page. Note that this alternate break sequence is only active once the kernel has started running multiuser and processed the default file. While the ROM is active (during power-on and during the boot process) and while running single-user, you still need to use a BREAK to get to the ROM prompt. The console client can cause the server to send a BREAK using the escape sequence "^Ecl1" (i.e. escape, c, ell, one).

If you have a Sun software support contract, there are patches available for Solaris 2.6 and 2.7 that add the"alternate break" capability integrated into Solaris 2.8. Solaris 2.6 requires patch 105924-10 or higher. Solaris 2.7 requires patch 107589-02 or higher.

We have added this patch to all our Solaris 2.6 servers, and added it (and the entry in the /etc/default/kbd file) to our jumpstart configuration so it will automatically be added to every new install.

We have confirmed by direct testing that neither the Cisco 16xx, 26xx, or Catalyst hardware suffers from the BREAK sent when the Stallion card loses power.

Using a Serial Console on FreeBSD

The procedure for doing this is described in detail in the FreeBSD Handbook. This is a quick summary.

Check the kernel configuration

Check that the kernel configuration file has flags 0x10 in the config line for the sio0 device. This signals this device (known as COM1 in DOS/Windows or /dev/ttyd0 in FreeBSD) can be used as a console. This flag is set on the GENERIC and LINT sample configs, so is likely to be set in your kernel.

Create the /boot.conf file

This file should be created containing a single line containing just "-h". This tells the FreeBSD boot blocks to use the serial console.

Edit /etc/ttys

Edit this file and make the following changes.

If you are not going to have any keyboard/video screen on this server at all, you should find all the lines for ttyv0 through ttyv8:

 ttyv1   "/usr/libexec/getty Pc"         cons25  on  secure

Change the on to off. This will stop login screens being run on the useless video consoles.

Find the line containing ttyd0. Change it from

 ttyd0   "/usr/libexec/getty std.9600"   dialup  off secure

to

 ttyd0   "/usr/libexec/getty std.9600"   vt100   on secure

(replacing vt100 with the term type of your console. xterms might be a good choice). This allows you to log in to the console port once the system is running multi-user.

Reboot and away you go!

Security Implications

The client-server protocol for conserver requires the user of the console client to enter a password. This password is passed across the net in cleartext!!! This means conserver is not really suitable for use across untrusted networks (such as the Internet). Use of conserver-only passwords (in the conserver.passwd file) slightly mitigate this problem, but anyone sniffing a conserver connection can easily get console access, and from there prang your machine using the console break sequence. For operating across the Internet, use something secure like SSH to log into to the server machine, and run the console client there.

On Conserver Versions

The conserver program has fractured into a number of versions. The home page referenced above seems to be the latest and most featureful version around, and carries a version number of "7.0.2". This is maintained by Bryan Stansell (bryan@conserver.com), who has brought together the work of many people (listed on his webpage).

The FreeBSD ports collection contains a port for version 8.5 of conserver. This seems to be older and less featureful than the 7.0.2 version (in particular, it does not support consoles connected to terminal server ports and does not support a conserver.passwd file), and is written in a fairly idiosyncratic manner (using a preprocessor to generate C code). Version 8.5 is maintained by Kevin S Braunsdorf (ksb+conserver@sa.fedex.com) who did most of the original work on conserver, and whose work Bryan Stansell is building on. The 8.5 version does support one feature not in the 7.0.2 version (controlling power to remote machines via a specific serial-interfaced power controller hardware).

As shipped with FreeBSD, the 8.5 version does not authenticate against FreeBSD servers using MD5 passwords. There is a patch in the FreeBSD GNATS system (ports/28432) that fixes this problem. Kevin has indicated this patch will be included in future versions of conserver from him. There are a couple of other problems with the 8.5 version as well.

Links

Homepage for the latest version of conserver.

FTP the conserver 7.0.2 source tarball.

Stallion Technologies homepage.

David Harris' Minor Scroll Of Console Knowledge contains heaps of good information on serial consoles and serial comms in general.

His Greater Scroll of Console Knowledge contains evern more specific info on connecting various devices to various other devices. Oh the joys of standards!

Doug Hughes has a similar console server based on the screen program and an old SunOs host.

The Real Weasel company makes a ISA or PCI video card that looks like a PC video card but actually talks to a serial port. This can be used to implement serial consoles on PC hardware for operating systems that can not be forced to use serial console ports early enough.

Files

Stallion Jumbo Patch for FreeBSD 4 (unzipped, 400k)
The same Stallion Jumbo Patch for FreeBSD 4 (gzipped, 140k)
A FreeBSD port framework for conserver 7.0.2.
The Port framework as a SHAR file

Man Pages

console(8)
conserver(8)
conserver.cf(5)

Change Log

10 July, 2001
Initial version announced on FreeBSD and Sage-AU mailing lists.
12 July, 2001
13 July, 2001
18 July, 2001
Gregory Bond
Last modified: Thu Jul 19 10:19:28 EST 2001
-$Id: article.sgml,v 1.5 2001-10-31 23:10:30 chern Exp $ +$Id: article.sgml,v 1.6 2002-06-28 23:44:36 keramida Exp $ diff --git a/en_US.ISO8859-1/articles/hubs/article.sgml b/en_US.ISO8859-1/articles/hubs/article.sgml index eb4d9ee5ce..d15451e884 100644 --- a/en_US.ISO8859-1/articles/hubs/article.sgml +++ b/en_US.ISO8859-1/articles/hubs/article.sgml @@ -1,1085 +1,1085 @@ %man; %authors; %mailing-lists; ]>
Mirroring FreeBSD $FreeBSD$ Jun Kuriyama
kuriyama@FreeBSD.org
 Valentino Vaschetto
logo@FreeBSD.org
 Daniel Lang
dl@leo.org
 An in-progress article on how to mirror FreeBSD, aimed at hub administrators Requirements for FreeBSD mirrors Disk Space Disk space is one of the most important requirements. Depending on the set of releases, architectures, and degree of completeness you want to mirror, a huge amount of disk space may be consumed. Also keep in mind, that official mirrors are probably required to be complete. The CVS repository and the web pages should always be mirrored completely. Also note, that the numbers stated here, are reflecting the current state (at 4.5-RELEASE). Further development and releases will only increase the required amount. Also make sure, to keep some (ca. 10-20%) extra space around, just to be sure. Here are some approximate figures: Full FTP Distribution: 60 GB CVS repository: 1.4 GB CTM deltas: 1.5 GB Webpages: 150 MB Network Connection/Bandwidth Of course, you need to be connected to the internet. The required bandwidth depends on your intended use of the mirror. If you just want to mirror some parts of FreeBSD for local use at your site/intranet, the demand may be much smaller, than if you want to make the files publicly available or even if you intend to become an official mirror. We can only give rough estimates here: Local site, no public access: basically no minimum, but < 2 Mbps could make syncing a pain. Unofficial public site: 34 Mbps is probably a good start. Official site: > 100 Mbps is recommended, also your host should be connected as close as possible to your border router. System Requirements, CPU, RAM This also depends on the expected amount of clients, which is determined by the servers policy. It is also affected by the types of services you want to offer. Plain FTP or HTTP services may not require a huge amount of resources. Watch out, if you provide CVSup, rsync or even AnonCVS. This can have a huge impact on CPU and memory requirements. Especially rsync is considered a memory hog, and CVSup does indeed consume some CPU. For AnonCVS it might be a nice idea to set up a memory resident filesystem (MFS) of at least 300 MB, so you need to take this into account for your memory requirements. The following are just examples to give you a very rough hint. For a moderately visited site, that offers rsync, you might consider a current CPU with around 800Mhz - 1 GHz, and at least 512MB RAM. This is probably the minimum you want for an official site. For a frequently used site you need definitely more RAM (consider 2GB as a good start), and possibly more CPU, which could also mean, that you need to go for a SMP system. You also want to consider a fast disk subsystem. Operations on the CVS repository require a fast disk subsystem (RAID is greatly advised). A SCSI controller that has a cache of its own can also speed up things, since most of these services incur a very large number of small modifications to the disk. You can also experiment with enlarging the portion of system memory which is used for the filesystem buffer cache. This will also help to reduce the quantity of disk access. This can be done with the BUFCACHEPERCENT kernel option. The default is to use 5% of system memory. Services to offer Every mirror site is required to have a set of core services available. In addition to these basic services, which mirrors are required to provide, there is a number of optional services that server administrators may choose to offer. This section explains which services you can provide and how to go about implementing them. FTP (required for FTP fileset) This is one of the most basic services, and it is required for each mirror, offering public FTP distributions. FTP access must be anonymous, and no upload/download ratios are allowed (a ridiculous thing anyway). Upload capability is not required (and must never be allowed for the FreeBSD file space). Also the FreeBSD archive should be available under the path /pub/FreeBSD. There is a lot of software available which can be set up to allow anonymous FTP (in alphabetical order). /usr/libexec/ftpd: FreeBSD's own ftpd can be used. Be sure to read &man.ftpd.8;. ftp/ncftpd: A commercial package, free for educational use. ftp/oftpd: An ftpd designed with security as a main focus. ftp/proftpd: A modular and very flexible ftpd. ftp/pure-ftpd: Another ftpd developed with security in mind. ftp/twoftpd: As above. ftp/vsftpd: The very secure ftpd. ftp/wu-ftpd: The ftpd from Washington University. It has become infamous, because of the huge amount of security issues that have been found in it. If you do choose to use this software be sure to keep it up to date. FreeBSD's ftpd, proftpd, wu-ftpd and maybe ncftpd are among the most commonly ones. The others do not have a large userbase among mirror sites. RSYNC (optional for FTP fileset) Rsync is often also offered for convenience, for the contents of the FTP area of FreeBSD. The protocol is different from FTP in many ways, and overall, it can be stated, that it is much more bandwidth friendly, as only differences between files are transferred, not whole files. Rsync does require significant amount of memory for each instance. The size depends on the size of the synced module in terms of number of directories and files. Rsync can use rsh and ssh (now default) as a transport, or use it's own protocol for stand-alone access (this is the preferred method for public rsync servers). Authentication, connection limits, and other restrictions may be applied. There is just one software package available: net/rsync HTTP (required for webpages, optional for FTP fileset) If you want to offer the FreeBSD webpages, you need to install a webserver a.k.a httpd. You may optionally offer the FTP fileset via HTTP. The choice of Webserver software is left up to the mirror administrator. Some of the most popular choices are: www/apache13: Apache is the most widely deployed Webserver on the Internet. It is used extensively by the FreeBSD Project. You may also wish to use the next generation of the Apache Webserver, available in the ports collection as www/apache2. www/thttpd: If you are going to be serving a lot amount of static content you may find that using an application such as tHttpd is more efficient than Apache. It is optimized for excellent performance on FreeBSD. www/boa: Boa is another alternative to tHttpd and Apache. It should provide considerably better performance than Apache for purely static content. It does not, at the time of writing, contain the same set of optimizations for FreeBSD that are found in tHttpd. CVSup (desired for CVS repository) CVSup is a very efficient way of distributing files. It works similar as rsync, but was specially designed for the use with CVS repositories. If you want to offer the FreeBSD CVS repository, you really want to consider offering it via CVSup. Still it is possible to offer the CVS repository via AnonCVS, FTP, Rsync or HTTP, but people would benefit much more from CVSup access. CVSup was developed by &a.jdp;. It is a bit tricky to install on non-FreeBSD platforms, since it is written in Modula-3 and therefore requires a Modula-3 environment. John Polstra has built a stripped down version of M3, that is sufficient to run CVSup, and can be installed much easier. See Ezm3 for details. Related ports are: net/cvsup: The native CVSup port (client and server) which requires lang/ezm3 now. net/cvsup-mirror: The CVSup mirror kit, which requires net/cvsup, and configures it mirror-ready. Some site administrators may want a different setup, though. There are a few more like net/cvsupit and net/cvsup-without-gui you might want to have a look at. If you prefer a static binary package, take a look here. This page stil refers to the S1G bug, that was present in CVSup. Maybe John will setup a generic download-site to get static binaries for various platforms. It is possible to use CVSup to offer any kind of fileset, not just CVS repositories, but configuration can be complex. CVSup is known to eat some CPU on the server as on the client, since it needs to compare lots of files. AnonCVS (optional for CVS repository) If you have the CVS repository, you may want to offer anonymous CVS access. A short warning first: There is not that much demand for it, and it requires some experience and you need to know, what you are doing. Generally there are two ways, how to access a CVS repository remotely: via pserver or via ssh (we don't consider rsh). For anonymous access, pserver is very well suited, but some still offer ssh access as well. There is a custom crafted wrapper in the CVS repository, to be used as a login-shell for the anonymous ssh account. It does a chroot, and therefore requires the CVS repository to be available under the anonymous user's home-directory, which may not be possible for all sites. If you just offer pserver this restriction does not apply, but you may run with more security risks. You don't need to install any special software, since &man.cvs.1; comes with FreeBSD. You need to enable access via inetd, so add an entry into your /etc/inetd.conf like this: cvspserver stream tcp nowait root /usr/bin/cvs cvs -f -l -R -T /anoncvstmp --allow-root=/home/ncvs pserver See the manpage for details of the options. See also the cvs info page, about additional ways to make sure, access is read-only. It is advisable, that you create an unprivileged account, preferably called anoncvs. Also you need to create a file passwd in your /home/ncvs/CVSROOT and assign a CVS password (empty or anoncvs) to that user. The directory /anoncvstmp is a special purpose memory based filesystem. It is not required but advised, since &man.cvs.1; creates a shadow directory structure in your /tmp which is not used after the operation, but slows things dramatically, if real disk operations are required. Here is an excerpt from /etc/fstab, how to set up such a MFS: /dev/da0s1b /anoncvstmp mfs rw,-s=786432,-b=4096,-f=512,-i=560,-c=3,-m=0,nosuid,nodev 0 0 This is (of course) tuned a lot, and was suggested by &a.jdp;. How to mirror FreeBSD Ok now, you know the requirements, and how to offer the services, but not how to get it. :-) This section explains how to actually mirror the various parts of FreeBSD, what tools to use, and where to mirror from. FTP The FTP area is the largest amount of data, that needs to be mirrored. It includes the distributions sets, required for network installation, the branches, that are actually snapshots of checked-out source trees, the ISO Images to write CD-Roms with the installation distribution, a live filesystem, and lots of packages, the ports tree, distfiles and a huge amount of packages. All of course for various FreeBSD versions, and i386 and alpha architecture. With FTP mirror You can use a FTP mirror program, to get the files. There are a lot around, and widely used, like: ftp/mirror ftp/ftpmirror ftp/emirror ftp/spegla ftp/omi some even use ftp/wget ftp/mirror was very popular, but seemed to have some drawbacks, as it is written in &man.perl.1;, and did have real problems on mirroring large directories like a FreeBSD site. There are rumors, that the current version has fixed this, by allowing to specify a different algorithm for comparing the directory structure. In general FTP is not really good for mirroring, since it transfers each whole file, if it has changed, and does not create a single data stream, that will benefit from a large TCP congestion window. With RSYNC A better way, to mirror the FTP area is rsync. You can install the port net/rsync and then use rsync to sync with your upstream host. rsync is already mentioned in . Since rsync access is not required, your preferred upstream site may not allow it. Since it is quite common, though, chances are small, that you cannot use it. You can always consider using an upstream server, that offers it, just for the benefits of rsync. Since the number of rsync clients will have a significant impact on the server machine, most admins impose limitations on their server. For a mirror, you should ask the site maintainer you are syncing from, about their policy, and maybe an exception for your host (since you are a mirror). A command line to mirror FreeBSD could look like that: &prompt.user; rsync -vaz --delete ftp4.de.freebsd.org::FreeBSD/ /pub/FreeBSD/ Consult the documentation for rsync, which is also available at http://rsync.samba.org/ about the various options to be used with rsync. Also you might want to set up a script framework, that calls such a command via &man.cron.8;. With CVSup A few sites, including the one-and-only ftp-master.freebsd.org even offer CVSup to mirror the contents of the FTP space. You need to install a cvsup client, preferably from the port: net/cvsup. (Also reread .) A sample supfile, suitable for ftp-master.freebsd.org looks like this: # # FreeBSD archive supfile from master server # *default host=ftp-master.FreeBSD.org *default base=/usr *default prefix=/pub #*default release=all *default delete use-rel-suffix *default umask=002 # If your network link is a T1 or faster, comment out the following line. #*default compress FreeBSD-archive release=all preserve It seems CVSup would be the best way to mirror the archive, in terms of efficiency, but it is only available from few sites. In fact I just know ftp-master.freebsd.org for sure. Please have look at the CVSup documentation like &man.cvsup.1; and consider using the option, as it can reduce the amount of work to be done a lot. Mirroring the CVS repository Again you have various possibilities, but the most recommended one, is to use CVSup. Using CVSup CVSup was already described to some detail in and . Here we just describe an example to set up the supfile: # # FreeBSD CVS supfile from master server # *default host=cvsup-master.FreeBSD.org *default base=/usr *default prefix=/pub/FreeBSD/development/FreeBSD-CVS *default release=cvs *default delete use-rel-suffix *default umask=002 # If your network link is a T1 or faster, comment out the following line. #*default compress cvs-all You should also have a look at /usr/share/examples/cvsup Please don't forget to consider the hint, mentioned in this note above. Using other methods Using other methods than CVSup is generally not recommended. We describe them in short here anyway. Since most sites offer the CVS repository as part of the FTP fileset under the path /pub/FreeBSD/development/FreeBSD-CVS, the following methods could be used. FTP RSYNC maybe even HTTP If you find a site, that supports it, you could use net/sup, but it is inferior to CVSup and it's deficiencies caused John Polstra to develop CVSup in the first place, so it is clearly not recommended. You can NOT use AnonCVS to mirror the CVS repository, since CVS does not allow you to access the repository itself, but only checked out versions of the modules. Mirroring the WWW pages The best way is, to check out the www distribution from CVS. If you have a local mirror of the CVS repository, it is probably as easy as: &prompt.user; cvs -d /home/ncvs co www and a cronjob, that calls cvs up -d -P on a regular basis, maybe just after your repository was updated. Of course, the files need to remain in a directory, available for public WWW access. The installation and configuration of a webserver is not discussed here. If you don't have a local repository, you can use CVSup to maintain an up to date copy of the www pages. A sample supfile can be found in /usr/share/examples/cvsup/www-supfile and could look like this: # # WWW module supfile for FreeBSD # *default host=cvsup3.de.FreeBSD.org *default base=/usr *default prefix=/usr/local *default release=cvs tag=. *default delete use-rel-suffix # If your network link is a T1 or faster, comment out the following line. *default compress # This collection retrieves the www/ tree of the FreeBSD repository www Using ftp/wget or other web-mirror tools, is probably not recommended. Mirroring the FreeBSD documentation As the documentation is referenced a lot from the webpages, it is recommended, that you mirror the FreeBSD documentation as well. However, this is not so trivial as the www-pages alone. First of all, you should get the doc sources, again preferably via CVSup. Here is a corresponding sample supfile: # # FreeBSD documentation supfile # *default host=cvsup3.de.FreeBSD.org *default base=/usr *default prefix=/usr/share *default release=cvs tag=. *default delete use-rel-suffix # If your network link is a T1 or faster, comment out the following line. #*default compress # This will retrieve the entire doc branch of the FreeBSD repository. # This includes the handbook, FAQ, and translations thereof. doc-all Then you need to install a couple of ports. You are lucky, that there is a meta-port: textproc/docproj to do the work for you. You need to setup some environment variables, like SGML_CATALOG_FILES, also have a look at your /etc/make.conf (copy /etc/defaults/make.conf if you don't have one), and look at the DOC_LANG variable. Now you are probably ready to run make in you doc directory (/usr/share/doc by default) and build the documentation. Again you need to make it accessible for your webserver and make sure, the links point to the right location. The building of the documentation, as well as lots of side issues, is documented itself in: fdp-primer. Please read this piece of documentation, especially if you have problems, building the documentation. XXX MAYBE THIS CAN BE LINKED FROM WITHIN - NOT USING AN ABSOLUTE URL XXX How often should I mirror? Every mirror should be updated on a regular basis. You will certainly need some script framework for it, that will be called by &man.cron.8;. Since nearly every admin does this his own way, we cannot give specific instructions. It could work like this: Put the command to run your mirroring application in a script. Use of a plain /bin/sh script is recommended. Add some output redirections, so diagnostic messages are logged to a file. Test, if your script works. Check the logs. Use &man.crontab.1; to add the script the appropriate user's &man.crontab.5;. Here are some recommended schedules: FTP fileset: daily CVS repository: daily to hourly WWW pages: daily Where to mirror from This is an important issue. So this section will spend some effort to explain the backgrounds. A few words about the organization Mirrors are organized by country. All official mirrors have a DNS entry of the form ftpN.CC.freebsd.org. Whith CC (i.e. country code) beeing the top level domain of the country, where this mirror is located; and N is a number, telling that the host would be the Nth mirror in that country. (Same applies to cvsupN.CC.freebsd.org, wwwN.CC.freebsd.org, etc.) There are mirrors with no CC part. These are usually located in the US, but don't need to. ftp.freebsd.org is currently located in Denmark and just another mirror (i.e. it is NO master site). Additionally there exists a hierarchy of mirrors, which is described terms of tiers. The master sites are not referred to, but can be described as Tier-0. Mirrors that mirror from these sites can be considered Tier-1, mirrors of Tier-1-mirrors, are Tier-2, etc. Official sites are encouraged to be of a low tier, but the lower the tier, the higher the requirements in terms as described in . Also access to low-tier-mirrors may be restricted, and access to master sites is definitely restricted. The tier-hierarchy is not reflected by DNS and generally not documented anywhere, except for the master sites. However, official mirrors with low numbers, like 1-4, are usually Tier-1 (this is just a rough hint, and there's no rule). Ok, but where should I get the stuff now? The short answer is: from the site, that is closest to you in internet terms, or gives you the fastest access. I just want to mirror from somewhere! If you have no special intentions or requirements, the statement in applies. This means: Look at available mirrors in your country. The FreeBSD Mirror Database can help you with this. Check roughly those, which provide fastest access (number of hops, round-trip-times) and offer the services you intend to use (like rsync or CVSup). Contact the admins of your chosen site, stating your request, and asking about their terms and policies. Setup your mirror as described above. I'm an official mirror, what is the right site for me? In general the description in still applies. Of course you may want to put some weight on the fact, that your upstream should be of a low tier. There are some other considerations about official mirrors, that are described in . I want to access the master sites! If you have good reasons, and good prerequisites, you may want and get access to one of the master sites. Access to these sites is generally restricted, and there are special policies for access. If you are already an official mirror, this certainly helps you getting access. In any other case make sure your country really needs another mirror. If it already has three or more, ask the &a.hubs; first. There are just two master sites, one for the FTP fileset and one for the CVS repository (the webpages and docs are obtained from CVS, so there is no need for it). ftp-master.freebsd.org This is the master site for the FTP fileset. ftp-master.FreeBSD.org provides rsync and CVSup access, rather in addition to ftp protocol. Refer to and how to access via these protocols. Mirrors should be encouraged to also allow rsync access for the FTP contents, since they are Tier-1-mirrors. To get access to ftp-master.FreeBSD.org, you need to contact &a.peter;. cvsup-master.freebsd.org This is the master site for the CVS repository. cvsup-master.FreeBSD.org provides CVSup access only. See for details. To get access, you need to contact &a.jdp;. Make sure you read FreeBSD CVSup Access Policy first! Set up the required authentication by following these instructions. Make sure you specify the server as freefall.freebsd.org on the cvpasswd command line, as described in this document, even when you are contacting cvsup-master.freebsd.org Official Mirrors Official mirrors are mirrors that a) have a freebsd.org DNS entry (usually a CNAME). b) are listed as an official mirror in the FreeBSD documentation (like handbook). So far to distinguish official mirrors. Official mirrors are not necessarily Tier-1-mirrors. However you probably won't find a Tier-1-mirror, that is not also official. Special Requirements for official (tier-1) mirrors It is not so easy to state requirements for all official mirrors, since the project is sort of tolerant here. It is more easy to say, what official tier-1 mirrors are required to. All other official mirrors can consider this a big should. The following applies mainly to the FTP fileset, since a CVS repository should always be mirrored completely, and the webpages are a case of its own. Tier-1 mirrors are required to: to carry the complete fileset allow access to other mirror sites provide FTP and RSYNC access Furthermore, admins should be subscribed to the &a.hubs;. See this link for details, how to subscribe. It is very important for a hub administrator, especially Tier-1 hub admins, to check the release schedule for the next FreeBSD release. This is important because it will tell you when the next release is scheduled to come out, and thus giving you time to prepare for the big spike of traffic which follows it. It is also eminent that hub administrators try to keep their mirrors as up-to-date as possible (again, even more crucial for Tier-1 mirrors). If Mirror1 doesn't update for a while, lower tier mirrors will begin to mirror old data from Mirror1 and thus begins a downward spiral... Keep your mirrors up to date! How to become official then? An interesting question, especially, since the state of being official comes with some benefits, like a much higher bill from your ISP, as more people will be using your site. Also it may be a key requirement, to get access to a master site. Before applying, please consider (again) if another official mirror is really needed for your region. Ask on the &a.hubs;, if in doubt. Ok, here is how to do it: Get the mirror running in first place (maybe not using a master site, yet). Subscribe to the &a.hubs;. If everything works so far, contact the DNS admin, responsible for your region/country, and ask for a DNS entry for your site. The admin should able to be contacted via hostmaster@cc.freebsd.org, which cc being your country code/TLD again. Your DNS entry will look like described in . If there is no subdomain delegated, yet, for your country, you probably need to contact hostmaster@freebsd.org, however, you can try the &a.hubs; first. Then you can ask the &a.doc; or the &a.hubs; to add your mirror site to the mirror list in the - FreeBSD + FreeBSD Handbook. Make sure you tell them the email address, to list as the maintainer of the site. This is it. Some statistics from mirror sites Here are links to the stat pages of your favorite mirrors (a.k.a. the only ones who feel like providing stats). FTP site statistics ftp2.FreeBSD.org - grisha@ispol.com - (Bandwidth) ftp.is.FreeBSD.org - hostmaster@is.FreeBSD.org - (Bandwidth) (FTP processes) (HTTP processes) ftp.cz.FreeBSD.org - cejkar@fit.vutbr.cz - (Bandwidth) (FTP processes) (Rsync processes) ftp4.de.FreeBSD.org - dl@leo.org - (FTP users) (RSYNC users) (Bandwidth) CVSup site stats cvsup5.FreeBSD.org - staff@blackened.com - (CVSup processes) cvsup[23456].jp.FreeBSD.org - kuriyama@FreeBSD.org - (CVSup processes) cvsup.cz.FreeBSD.org - cejkar@fit.vutbr.cz - (CVSup processes) [cvsup3|anoncvs].de.FreeBSD.org - dl@leo.org - (CVSup processes)
diff --git a/en_US.ISO8859-1/articles/releng/article.sgml b/en_US.ISO8859-1/articles/releng/article.sgml index 04252ce739..8c49b0ad95 100644 --- a/en_US.ISO8859-1/articles/releng/article.sgml +++ b/en_US.ISO8859-1/articles/releng/article.sgml @@ -1,908 +1,908 @@ %authors; %teams; %mailing-lists; %man; %freebsd; The Release Engineering of Third Party Packages'> ]>
FreeBSD Release Engineering November 2001 BSDCon Europe Murray Stokely I've been involved in the development of FreeBSD based products since 1997 at Walnut Creek CDROM, BSDi, and now Wind River Systems. FreeBSD 4.4 was the first official release of FreeBSD that I played a significant part in.
murray@FreeBSD.org http://www.FreeBSD.org/~murray
$FreeBSD$ This paper describes the approach used by the FreeBSD release engineering team to make production quality releases of the FreeBSD Operating System. It details the methodology used for the release of FreeBSD 4.4 and describes the tools available for those interested in producing customized FreeBSD releases for corporate rollouts or commercial productization. Introduction The development of FreeBSD is a very open process. FreeBSD is comprised of contributions from thousands of people around the world. The FreeBSD Project provides anonymous CVS[1] access to the general public so that others can have access to log messages, diffs (patches) between development branches, and other productivity enhancements that formal source code management provides. This has been a huge help in attracting more talented developers to FreeBSD. However, I think everyone would agree that chaos would soon manifest if write access was opened up to everyone on the Internet. Therefore only a select group of nearly 300 people are given write access to the CVS repository. These committers[6] are responsible for the bulk of FreeBSD development. An elected core-team[7] of very senior developers provides some level of direction over the project. The rapid pace of FreeBSD development leaves little time for polishing the development system into a production quality release. To solve this dilemma, development continues on two parallel tracks. The main development branch is the HEAD or trunk of our CVS tree, known as FreeBSD-CURRENT or -CURRENT for short. A more stable branch is maintained, known as FreeBSD-STABLE or -STABLE for short. Both branches live in a master CVS repository in California and are replicated via CVSup[2] to mirrors all over the world. FreeBSD-CURRENT[8] is the bleeding-edge of FreeBSD development where all new changes first enter the system. FreeBSD-STABLE is the development branch from which major releases are made. Changes go into this branch at a different pace, and with general assumption that they have first gone into FreeBSD-CURRENT and have been thoroughly tested by our user community. In the interim period between releases, nightly snapshots are built automatically by the FreeBSD Project build machines and made available for download from ftp://stable.FreeBSD.org/. The widespread availability of binary release snapshots, and the tendency of our user community to keep up with -STABLE development with CVSup and make world[8] helps to keep FreeBSD-STABLE in a very reliable condition even before the quality assurance activities ramp up pending a major release. Bug reports and feature requests are continuously submitted by users throughout the release cycle. Problems reports are entered into our GNATS[9] database through email, the &man.send-pr.1; application, or via the web interface provided at In addition to the multitude of different technical mailing lists about FreeBSD, the &a.qa; provides a forum for discussing the finer points of release-polishing. To service our most conservative users, individual release branches were introduced with FreeBSD 4.3. These release branches are created shortly before a final release is made. After the release goes out, only the most critical security fixes and additions are merged onto the release branch. In addition to source updates via CVS, binary patchkits are available to keep systems on the RELENG_4_3 and RELENG_4_4 branches updated. discusses the different phases of the release engineering process leading up to the actual system build and describes the actual build process. describes how the base release may be extended by third parties and details some of the lessons learned through the release of FreeBSD 4.4. Finally, presents future directions of development. Release Process New releases of FreeBSD are released from the -STABLE branch at approximately four month intervals. The FreeBSD release process begins to ramp up 45 days before the anticipated release date when the release engineer sends an email to the development mailing lists to remind developers that they only have 15 days to integrate new changes before the code freeze. During this time, many developers perform what have become know as MFC sweeps. MFC stands for Merge From CURRENT and it describes the process of merging a tested change from our -CURRENT development branch to our -STABLE branch. Code Review Thirty days before the anticipated release, the source repository enters a code slush. During this time, all commits to the -STABLE branch must be approved by the &a.re;. The kinds of changes that are allowed during this 15 day period include: Bug fixes. Documentation updates. Security-related fixes of any kind. Minor changes to device drivers, such as adding new Device IDs. Any additional change that the release engineering team feels is justified, given the potential risk. After the first 15 days of the code slush, a release candidate is released for widespread testing and the code enters a code freeze where it becomes much harder to justify new changes to the system unless a serious bug-fix or security issue is involved. During the code freeze, at least one release candidate is released per week, until the final release is ready. During the days leading to the final release, the release engineering team is in constant communication with the security-officer team, the documentation maintainers, and the port maintainers, to ensure that all of the different components required for a successful release are available. Final Release Checklist When several release candidates have been made available for widespread testing and all major issues have been resolved, the final release polishing can begin. Creating the Release Branch As described in the introduction, the RELENG_X_Y release branch is a relatively new addition to our release engineering methodology. The first step in creating this branch is to ensure that you are working with the newest version of the RELENG_X sources that you want to branch from. /usr/src&prompt.root; cvs update -rRELENG_4 -P -d The next step is to create a branch point tag, so that diffs against the start of the branch are easier with CVS: /usr/src&prompt.root; cvs rtag -rRELENG_4 RELENG_4_4_BP src And then a new branch tag is created with: /usr/src&prompt.root; cvs rtag -b -rRELENG_4_4_BP RELENG_4_4 src The RELENG_* tags are restricted for use by the CVS-meisters and release engineers. A tag is CVS vernacular for a label that identifies the source at a specific point in time. By tagging the tree, we ensure that future release builders will always be able to use the same source we used to create the official FreeBSD Project releases. &branches.ascii; FreeBSD Development Branches Bumping up the Version Number Before the final release can be tagged, built, and released, the following files need to be modified to reflect the correct version of FreeBSD: doc/en_US.ISO8859-1/books/handbook/mirrors/chapter.sgml doc/share/sgml/freebsd.ent src/Makefile.inc src/UPDATING src/contrib/groff/tmac/doc-common src/contrib/groff/tmac/groff_mdoc.man src/gnu/usr.bin/groff/tmac/mdoc.local src/release/Makefile src/release/doc/en_US.ISO8859-1/share/sgml/release.dsl src/release/doc/share/examples/Makefile.relnotesng src/release/doc/share/sgml/release.ent src/share/examples/cvsup/standard-supfile src/sys/conf/newvers.sh src/sys/sys/param.h www/en/releases/* www/en/docs.sgml www/en/cgi/ports.cgi The release notes and errata files also need to be adjusted for the new release (on the release branch) and truncated appropriately (on the stable/current branch): src/release/doc/en_US.ISO8859-1/relnotes/common/new.sgml src/release/doc/en_US.ISO8859-1/errata/article.sgml Sysinstall should be updated to note the number of available ports and the amount of disk space required for the Ports Collection. This information is currently kept in src/release/sysinstall/dist.c. Creating Release Tags When the final release is ready, the following command will create the RELENG_4_4_0_RELEASE tag. /usr/src&prompt.root; cvs rtag -rRELENG_4_4 RELENG_4_4_0_RELEASE src The Documentation and Ports managers are responsible for tagging the respective trees with the RELEASE_4_4_0 tag. Occasionally, a last minute fix may be required after the final tags have been created. In practice this isn't a problem, since CVS allows tags to be manipulated with cvs tag -d tagname filename. It is very important that any last minute changes be tagged appropriately as part of the release. FreeBSD releases must always be reproduceable. Local hacks in the release engineer's environment are not acceptable. Release Building FreeBSD releases can be built by anyone with a fast machine and access to a source repository. (That should be everyone, since we offer anonymous CVS! See The Handbook for details.). The only special requirement is that the vn (On -CURRENT, this device has been replaced by the new md memory disk driver .) device must be available. If the device is not loaded into your kernel, then the kernel module should be automatically loaded when &man.vnconfig.8; is executed during the boot media creation phase. All of the tools necessary to build a release are available from the CVS repository in src/release. These tools aim to provide a consistent way to build FreeBSD releases. A complete release can actually be built with only a single command, including the creation of ISO images suitable for burning to CDROM, installation floppies, and an FTP install directory. This command is aptly named make release. <quote>make release</quote> To successfully build a release, you must first populate /usr/obj by running make world or simply make buildworld. The release target requires several variables be set properly to build a release: CHROOTDIR - The directory to be used as the chroot environment for the entire release build. BUILDNAME - The name of the release to be built. CVSROOT - The location of a CVS Repository. RELEASETAG - The CVS tag corresponding to the release you would like to build. If you do not already have access to a local CVS repository, then you may mirror one with CVSup. + url="http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/synching.html#CVSUP">CVSup. The supplied supfile, /usr/share/examples/cvsup/cvs-supfile, is a useful starting point for mirroring the CVS repository. If RELEASETAG is omitted, then the release will be built from the HEAD (a.k.a. -CURRENT) branch. Releases built from this branch are normally referred to as -CURRENT snapshots. There are many other variables available to customize the release build. Most of these variables are documented at the top of src/release/Makefile. The exact command used to build the official FreeBSD 4.4 (x86) release was: make release CHROOTDIR=/local3/release \ BUILDNAME=4.4-RELEASE \ CVSROOT=/host/cvs/usr/home/ncvs \ RELEASETAG=RELENG_4_4_0_RELEASE The release Makefile can be broken down into several distinct steps. Creation of a sanitized system environment in a separate directory hierarchy with make installworld. Checkout from CVS of a clean version of the system source, documentation, and ports into the release build hierarchy. Population of /etc and /dev in the chrooted environment. chroot into the release build hierarchy, to make it harder for the outside environment to taint this build. make world in the chrooted environment. Build of Kerberos-related binaries. Build GENERIC kernel. Creation of a staging directory tree where the binary distributions will be built and packaged. Build and installation of the documentation toolchain needed to convert the documentation source (SGML) into HTML and text documents that will accompany the release. Build and installation of the actual documentation (user manuals, tutorials, release notes, hardware compatibility lists, and so on.) Build of the crunched binaries used for installation floppies. Package up distribution tarballs of the binaries and sources. Create the boot media and a fixit floppy. Create FTP installation hierarchy. (optionally) Create ISO images for CDROM/DVD media. For more information about the release build infrastructure, please see &man.release.7;. Building XFree86 XFree86 is an important component for many desktop users. The easiest way to build XFree86 is to use the src/release/scripts/X11/build_x.sh script. This script requires that XFree86 and Tcl/Tk already be installed on the build host. After compiling the necessary X servers, the script will package all of the files into tarballs that &man.sysinstall.8; expects to find in the XF86336 directory of the installation media. It is important to remove any site-specific settings from /etc/make.conf. For example, it would be unwise to distribute binaries that were built on a system with CPUTYPE set to a specific processor. Contributed Software (<quote>ports</quote>) The FreeBSD Ports collection is a collection of over &os.numports; third-party software packages available for FreeBSD. The &a.portmgr; is responsible for maintaining a consistent ports tree that can be used to create the binary packages that accompany official FreeBSD releases. The release engineering activities for our collection of third-party packages is beyond the scope of this document. A separate article, &art.re.pkgs;, covers this topic in depth. Release ISOs Starting with FreeBSD 4.4, the FreeBSD Project decided to release all four ISO images that were previously sold on the BSDi/Wind River Systems/FreeBSD Mall official CDROM distributions. Each of the four discs must contain a README.TXT file that explains the contents of the disc, a CDROM.INF file that provides meta-data for the disc so that &man.sysinstall.8; can validate and use the contents, and a filename.txt file that provides a manifest for the disc. This manifest can be created with a simple command: /stage/cdrom&prompt.root; find . -type f | sed -e 's/^\.\///' | sort > filename.txt The specific requirements of each CD are outlined below. Disc 1 The first disc is almost completely created by make release. The only changes that should be made to the disc1 directory are the addition of a tools directory, XFree86, and as many popular third party software packages as will fit on the disc. The tools directory contains software that allow users to create installation floppies from other operating systems. This disc should be made bootable so that users of modern PCs do not need to create installation floppy disks. If an alternate version of XFree86 is to be provided, then &man.sysinstall.8; must be updated to reflect the new location and installation instructions. The relevant code is contained in src/release/sysinstall on -STABLE or src/usr.sbin/sysinstall on -CURRENT. Specifically, the files dist.c, menus.c, and config.c will need to be updated. Disc 2 The second disc is also largely created by make release. This disc contains a live filesystem that can be used from &man.sysinstall.8; to troubleshoot a FreeBSD installation. This disc should be bootable and should also contain a compressed copy of the CVS repository in the CVSROOT directory and commercial software demos in the commerce directory. Discs 3 and 4 The remaining two discs contain additional software packages for FreeBSD. The packages should be clustered so that a package and all of its dependencies are included on the same disc. More information about the creation of these discs is provided in the &art.re.pkgs; article. Extensibility Although FreeBSD forms a complete operating system, there is nothing that forces you to use the system exactly as we have packaged it up for distribution. We have tried to design the system to be as extensible as possible so that it can serve as a platform that other commercial products can be built on top of. The only rule we have about this is that if you are going to distribute FreeBSD with non-trivial changes, we encourage you to document your enhancements! The FreeBSD community can only help support users of the software we provide. We certainly encourage innovation in the form of advanced installation and administration tools, for example, but we can't be expected to answer questions about it. Creating Customized Boot floppies Many sites have complex requirements that may require additional kernel modules or userland tools be added to the installation floppies. The quick and dirty way to accomplish this would be to modify the staging directory of an existing make release build hierarchy: Apply patches or add additional files inside the chroot release build directory. rm ${CHROOTDIR}/usr/obj/usr/src/release/release.[48] rebuild &man.sysinstall.8;, the kernel, or whatever parts of the system your change affected. chroot ${CHROOTDIR} ./mk release.4 chroot ${CHROOTDIR} ./mk release.8 New release floppies will be located in ${CHROOTDIR}/R/stage/floppies. Alternatively, the boot.flp make target can be called, or the filesystem creating script, src/release/scripts/doFS.sh, may be invoked directly. Local patches may also be supplied to the release build by defining the LOCAL_PATCH variable in make release. Scripting <command>sysinstall</command> The FreeBSD system installation and configuration tool, &man.sysinstall.8;, can be scripted to provide automated installs for large sites. This functionality can be used in conjunction with Intel's PXE[13] to bootstrap systems from the network, or via custom boot floppies with a sysinstall script. An example sysinstall script is available in the CVS tree as src/release/sysinstall/install.cfg. Lessons Learned from FreeBSD 4.4 The release engineering process for 4.4 formally began on August 1st, 2001. After that date all commits to the RELENG_4 branch of FreeBSD had to be explicitly approved by the &a.re;. The first release candidate for the x86 architecture was released on August 16, followed by 4 more release candidates leading up to the final release on September 18th. The security officer was very involved in the last week of the process as several security issues were found in the earlier release candidates. A total of over 500 emails were sent to the &a.re; in little over a month. Our user community has made it very clear that the security and stability of a FreeBSD release should not be sacrificed for any self-imposed deadlines or target release dates. The FreeBSD Project has grown tremendously over its lifetime and the need for standardized release engineering procedures has never been more apparent. This will become even more important as FreeBSD is ported to new platforms. Future Directions It is imperative for our release engineering activities to scale with our growing userbase. Along these lines we are working very hard to document the procedures involved in producing FreeBSD releases. Parallelism - Certain portions of the release build are actually embarrassingly parallel. Most of the tasks are very I/O intensive, so having multiple high-speed disk drives is actually more important than using multiple processors in speeding up the make release process. If multiple disks are used for different hierarchies in the chroot environment, then the CVS checkout of the ports and doc trees can be happening simultaneously to the make world on another disk. Using a RAID solution (hardware or software) can significantly decrease the overall build time. Cross-building releases - Building IA-64 or Alpha release on x86 hardware? make TARGET=ia64 release. Regression Testing - We need better automated correctness testing for FreeBSD. Installation Tools - Our installation program has long since outlived its intended life span. Several projects are under development to provide a more advanced installation mechanism. One of the most promising is the libh project[5] which aims to provided an intelligent new package framework and GUI installation program. Acknowledgements I would like to thank Jordan Hubbard for giving me the opportunity to take on some of the release engineering responsibilities for FreeBSD 4.4 and also for all of his work throughout the years making FreeBSD what it is today. Of course the release wouldn't have been possible without all of the release-related work done by &a.asami;, &a.steve;, &a.bmah;, &a.nik;, &a.obrien;, &a.kris;, &a.jhb; and the rest of the FreeBSD development community. I would also like to thank &a.rgrimes;, &a.phk;, and others who worked on the release engineering tools in the very early days of FreeBSD. This article was influenced by release engineering documents from the CSRG[14], the NetBSD Project[11], and John Baldwin's proposed release engineering process notes[12]. References [1] CVS - Concurrent Versions System [2] CVSup - The CVS-Optimized General Purpose Network File Distribution System [3] [4] FreeBSD Ports Collection [5] The libh Project [6] FreeBSD Committers [7] FreeBSD Core-Team [8] FreeBSD Handbook - + [9] GNATS: The GNU Bug Tracking System [10] FreeBSD PR Statistics [11] NetBSD Developer Documentation: Release Engineering [12] John Baldwin's FreeBSD Release Engineering Proposal [13] PXE Jumpstart Guide [14] Marshall Kirk McKusick, Michael J. Karels, and Keith Bostic: The Release Engineering of 4.3BSD
diff --git a/en_US.ISO8859-1/books/faq/book.sgml b/en_US.ISO8859-1/books/faq/book.sgml index da562010ec..324d2c7e2d 100644 --- a/en_US.ISO8859-1/books/faq/book.sgml +++ b/en_US.ISO8859-1/books/faq/book.sgml @@ -1,12489 +1,12489 @@ %man; %freebsd; %authors; %teams; %bookinfo; %mailing-lists; ]> Frequently Asked Questions for FreeBSD 2.X, 3.X and 4.X The FreeBSD Documentation Project $FreeBSD$ 1995 1996 1997 1998 1999 2000 2001 2002 The FreeBSD Documentation Project &bookinfo.legalnotice; This is the FAQ for FreeBSD versions 2.X, 3.X, and 4.X. All entries are assumed to be relevant to FreeBSD 2.0.5 and later, unless otherwise noted. Any entries with a <XXX> are under construction. If you are interested in helping with this project, send email to the &a.doc;. The latest version of this document is always available from the FreeBSD World Wide Web server. It may also be downloaded as one large HTML file with HTTP or as plain text, postscript, PDF, etc. from the FreeBSD FTP server. You may also want to Search the FAQ. Introduction Welcome to the FreeBSD 2.X-4.X FAQ! As is usual with Usenet FAQs, this document aims to cover the most frequently asked questions concerning the FreeBSD operating system (and of course answer them!). Although originally intended to reduce bandwidth and avoid the same old questions being asked over and over again, FAQs have become recognized as valuable information resources. Every effort has been made to make this FAQ as informative as possible; if you have any suggestions as to how it may be improved, please feel free to mail them to the &a.faq;. What is FreeBSD? Briefly, FreeBSD is a UN*X-like operating system for the i386 and Alpha/AXP platforms based on U.C. Berkeley's 4.4BSD-Lite release, with some 4.4BSD-Lite2 enhancements. It is also based indirectly on William Jolitz's port of U.C. Berkeley's Net/2 to the i386, known as 386BSD, though very little of the 386BSD code remains. A fuller description of what FreeBSD is and how it can work for you may be found on the FreeBSD home page. FreeBSD is used by companies, Internet Service Providers, researchers, computer professionals, students and home users all over the world in their work, education and recreation. See some of them in the FreeBSD Gallery. For more detailed information on FreeBSD, please see the FreeBSD Handbook. What is the goal of the FreeBSD Project? The goal of the FreeBSD Project is to provide software that may be used for any purpose and without strings attached. Many of us have a significant investment in the code (and project) and would certainly not mind a little financial compensation now and then, but we definitely do not insist on it. We believe that our first and foremost mission is to provide code to any and all comers, and for whatever purpose, so that the code gets the widest possible use and provides the widest possible benefit. This is, we believe, one of the most fundamental goals of Free Software and one that we enthusiastically support. That code in our source tree which falls under the GNU General Public License (GPL) or GNU Library General Public License (LGPL) comes with slightly more strings attached, though at least on the side of enforced access rather than the usual opposite. Due to the additional complexities that can evolve in the commercial use of GPL software, we do, however, endeavor to replace such software with submissions under the more relaxed FreeBSD copyright whenever possible. Does the FreeBSD license have any restrictions? Yes. Those restrictions do not control how you use the code, merely how you treat the FreeBSD Project itself. If you have serious license concerns, read the actual license. For the simply curious, the license can be summarized like this. Do not claim that you wrote this. Do not sue us if it breaks. Can FreeBSD replace my current operating system? For most people, yes. But this question is not quite that cut-and-dried. Most people do not actually use an operating system. They use applications. The applications are what really use the operating system. FreeBSD is designed to provide a robust and full-featured environment for applications. It supports a wide variety of web browsers, office suites, email readers, graphics programs, programming environments, network servers, and just about everything else you might want. Most of these applications can be managed through the Ports Collection. If you need to use an application that is only available on one operating system, you simply cannot replace that operating system. Chances are there is a very similar application on FreeBSD, however. If you want a solid office or Internet server, a reliable workstation, or just the ability to do your job without interruptions, FreeBSD will almost certainly do everything you need. Many computer users across the world, including both novices and experienced UNIX administrators, use FreeBSD as their only desktop operating system. If you are migrating to FreeBSD from some other UNIX environment, you already know most of what you need to. If your background is in graphic-driven operating systems such as Windows and older versions of Mac OS, expect to invest additional time learning the UNIX way of doing things. This FAQ and the FreeBSD Handbook are excellent places to start. Why is it called FreeBSD? It may be used free of charge, even by commercial users. Full source for the operating system is freely available, and the minimum possible restrictions have been placed upon its use, distribution and incorporation into other work (commercial or non-commercial). Anyone who has an improvement or bug fix is free to submit their code and have it added to the source tree (subject to one or two obvious provisions). It is worth pointing out that the word free is being used in two ways here, one meaning at no cost, the other meaning you can do whatever you like. Apart from one or two things you cannot do with the FreeBSD code, for example pretending you wrote it, you really can do whatever you like with it. What is the latest version of FreeBSD? Version &rel.current; is the latest RELEASE version; it was released in &rel.current.date;. This is also the latest STABLE version. Briefly, -STABLE is aimed at the ISP, corporate user, or any user who wants stability and a low change count over the wizzy new features of the latest -CURRENT snapshot. Releases can come from either branch, but -CURRENT should only be used if you are prepared for its increased volatility (relative to -STABLE, that is). Releases are made every few months. While many people stay more up-to-date with the FreeBSD sources (see the questions on FreeBSD-CURRENT and FreeBSD-STABLE) than that, doing so is more of a commitment, as the sources are a moving target. What is FreeBSD-CURRENT? FreeBSD-CURRENT is the development version of the operating system, which will in due course become 5.0-RELEASE. As such, it is really only of interest to developers working on the system and die-hard hobbyists. See the relevant section in the handbook for details on running -CURRENT. If you are not familiar with the operating system or are not capable of identifying the difference between a real problem and a temporary problem, you should not use FreeBSD-CURRENT. This branch sometimes evolves quite quickly and can be un-buildable for a number of days at a time. People that use FreeBSD-CURRENT are expected to be able to analyze any problems and only report them if they are deemed to be mistakes rather than glitches. Questions such as make world produces some error about groups on the -CURRENT mailing list may be treated with contempt. Every day, snapshot releases are made based on the current state of the -CURRENT and -STABLE branches. Nowadays, distributions of the occasional snapshot are now being made available. The goals behind each snapshot release are: To test the latest version of the installation software. To give people who would like to run -CURRENT or -STABLE but who do not have the time or bandwidth to follow it on a day-to-day basis an easy way of bootstrapping it onto their systems. To preserve a fixed reference point for the code in question, just in case we break something really badly later. (Although CVS normally prevents anything horrible like this happening :) To ensure that any new features in need of testing have the greatest possible number of potential testers. No claims are made that any -CURRENT snapshot can be considered production quality for any purpose. If you want to run a stable and fully tested system, you will have to stick to full releases, or use the -STABLE snapshots. Snapshot releases are directly available from ftp://current.FreeBSD.org/pub/FreeBSD/ for 5.0-CURRENT and releng4.FreeBSD.org for 4-STABLE snapshots. 3-STABLE snapshots are not being produced at the time of this writing (May 2000). Snapshots are generated, on the average, once a day for all actively developed branches. What is the FreeBSD-STABLE concept? Back when FreeBSD 2.0.5 was released, FreeBSD development branched in two. One branch was named -STABLE, one -CURRENT. FreeBSD-STABLE is intended for Internet Service Providers and other commercial enterprises for whom sudden shifts or experimental features are quite undesirable. It receives only well-tested bug fixes and other small incremental enhancements. FreeBSD-CURRENT, on the other hand, has been one unbroken line leading towards 5.0-RELEASE (and beyond) since 2.0 was released. If a little ASCII art would help, this is how it looks: 2.0 | | | [2.1-STABLE] *BRANCH* 2.0.5 -> 2.1 -> 2.1.5 -> 2.1.6 -> 2.1.7.1 [2.1-STABLE ends] | (Mar 1997) | | | [2.2-STABLE] *BRANCH* 2.2.1 -> 2.2.2-RELEASE -> 2.2.5 -> 2.2.6 -> 2.2.7 -> 2.2.8 [end] | (Mar 1997) (Oct 97) (Apr 98) (Jul 98) (Dec 98) | | 3.0-SNAPs (started Q1 1997) | | 3.0-RELEASE (Oct 1998) | | [3.0-STABLE] *BRANCH* 3.1-RELEASE (Feb 1999) -> 3.2 -> 3.3 -> 3.4 -> 3.5 -> 3.5.1 | (May 1999) (Sep 1999) (Dec 1999) (June 2000) (July 2000) | | [4.0-STABLE] *BRANCH* 4.0 (Mar 2000) -> 4.1 -> 4.1.1 -> 4.2 -> 4.3 -> 4.4 -> ... future 4.x releases ... | | (July 2000) (Sep 2000) (Nov 2000) \|/ + [5.0-CURRENT continues] The 2.2-STABLE branch was retired with the release of 2.2.8. The 3-STABLE branch has ended with the release of 3.5.1, the final 3.X release. The only changes made to either of these branches will be, for the most part, security-related bug fixes. 4-STABLE is the actively developed -STABLE branch. The latest release on the 4-STABLE is &rel.current;-RELEASE, which was released in &rel.current.date;. The 5-CURRENT branch is slowly progressing toward 5.0-RELEASE and beyond. See What is FreeBSD-CURRENT? for more information on this branch. When are FreeBSD releases made? The &a.re; releases a new version of FreeBSD about every four months, on average. Release dates are announced well in advance, so that the people working on the system know when their projects need to be finished and tested. A testing period precedes each release, in order to ensure that the addition of new features does not compromise the stability of the release. Many users regard this caution as one of the best things about FreeBSD, although waiting for all the latest goodies to reach -STABLE can be a little frustrating. More information on the release engineering process (including a schedule of upcoming releases) can be found on the release engineering pages on the FreeBSD Web site. For people who need or want a little more excitement, binary snapshots are made every day as discussed above. Who is responsible for FreeBSD? The key decisions concerning the FreeBSD project, such as the overall direction of the project and who is allowed to add code to the source tree, are made by a core team of 9 people. There is a much larger team of more than 200 committers who are authorized to make changes directly to the FreeBSD source tree. However, most non-trivial changes are discussed in advance in the mailing lists, and there are no restrictions on who may take part in the discussion. Where can I get FreeBSD? Every significant release of FreeBSD is available via anonymous FTP from the FreeBSD FTP site: For the current 3.X-STABLE release, 3.5.1-RELEASE, see the 3.5.1-RELEASE directory. The current 4-STABLE release, &rel.current;-RELEASE can be found in the &rel.current;-RELEASE directory. 4.X snapshots are usually made once a day. 5.0 Snapshot releases are made once a day for the -CURRENT branch, these being of service purely to bleeding-edge testers and developers. Information about obtaining FreeBSD on CD, DVD, and other media can be found in the Handbook. How do I access the Problem Report database? The Problem Report database of all user change requests may be queried (or submitted to) by using our web-based PR submission and query interfaces. The &man.send-pr.1; command can also be used to submit problem reports and change requests via electronic mail. Before submitting a problem report, please read Writing FreeBSD Problem Reports, an article on how to write good problem reports. How do I become a FreeBSD Web mirror? There are multiple ways to mirror the Web pages. You can retrieve the formatted files from a FreeBSD CVSup server using the application net/cvsup. The file /usr/share/examples/cvsup/www-supfile contains an example CVSup configuration file for web mirrors. You can download the web site source code from any FreeBSD FTP server using your favorite ftp mirror tool. Keep in mind that you have to build these sources before publishing them. Start mirroring at ftp://ftp.FreeBSD.org/pub/FreeBSD/FreeBSD-current/www. What other sources of information are there? Please check the Documentation list on the main FreeBSD web site. Documentation and Support What good books are there about FreeBSD? The project produces a wide range of documentation, available from this link: http://www.FreeBSD.org/docs.html. In addition, the Bibliography at the end of this FAQ, and the one in the Handbook reference other recommended books. Is the documentation available in other formats, such as plain text (ASCII), or Postscript? Yes. The documentation is available in a number of different formats and compression schemes on the FreeBSD FTP site, in the /pub/FreeBSD/doc/ directory. The documentation is categorized in a number of different ways. These include: The document's name, such as faq, or handbook. The document's language and encoding. These are based on the locale names you will find under /usr/share/locale on your FreeBSD system. The current languages and encodings that we have for documentation are as follows: Name Meaning en_US.ISO8859-1 US English de_DE.ISO8859-1 German es_ES.ISO8859-1 Spanish fr_FR.ISO8859-1 French ja_JP.eucJP Japanese (EUC encoding) ru_RU.KOI8-R Russian (KOI8-R encoding) zh_TW.Big5 Chinese (Big5 encoding) Some documents may not be available in all languages. The document's format. We produce the documentation in a number of different output formats. Each format has its own advantages and disadvantages. Some formats are better suited for online reading, while others are meant to be aesthetically pleasing when printed on paper. Having the documentation available in any of these formats ensures that our readers will be able to read the parts they are interested in, either on their monitor, or on paper after printing the documents. The currently available formats are: Format Meaning html-split A collection of small, linked, HTML files. html One large HTML file containing the entire document pdb Palm Pilot database format, for use with the iSilo reader. pdf Adobe's Portable Document Format ps Postscript rtf Microsoft's Rich Text Format Page numbers are not automatically updated when loading this format into Word. Press CTRLA, CTRLEND, F9 after loading the document, to update the page numbers. txt Plain text The compression and packaging scheme. There are three of these currently in use. Where the format is html-split, the files are bundled up using &man.tar.1;. The resulting .tar file is then compressed using the compression schemes detailed in the next point. All the other formats generate one file, called book.format (i.e., book.pdb, book.html, and so on). These files are then compressed using three compression schemes. Scheme Description zip The Zip format. If you want to uncompress this on FreeBSD you will need to install the archivers/unzip port first. gz The GNU Zip format. Use &man.gunzip.1; to uncompress these files, which is part of FreeBSD. bz2 The BZip2 format. Less widespread than the others, but generally gives smaller files. Install the archivers/bzip2 port to uncompress these files. So the Postscript version of the Handbook, compressed using BZip2 will be stored in a file called book.ps.bz2 in the handbook/ directory. The formatted documentation is also available as a FreeBSD package, of which more later. After choosing the format and compression mechanism that you want to download, you must then decide whether or not you want to download the document as a FreeBSD package. The advantage of downloading and installing the package is that the documentation can then be managed using the normal FreeBSD package management comments, such as &man.pkg.add.1; and &man.pkg.delete.1;. If you decide to download and install the package then you must know the filename to download. The documentation-as-packages files are stored in a directory called packages. Each package file looks like document-name.lang.encoding.format.tgz. For example, the FAQ, in English, formatted as PDF, is in the package called faq.en_US.ISO8859-1.pdf.tgz. Knowing this, you can use the following command to install the English PDF FAQ package. &prompt.root; pkg_add ftp://ftp.FreeBSD.org/pub/FreeBSD/doc/packages/faq.en_US.ISO8859-1.pdf.tgz Having done that, you can use &man.pkg.info.1; to determine where the file has been installed. &prompt.root; pkg_info -f faq.en_US.ISO8859-1.pdf Information for faq.en_US.ISO8859-1.pdf: Packing list: Package name: faq.en_US.ISO8859-1.pdf CWD to /usr/share/doc/en_US.ISO8859-1/books/faq File: book.pdf CWD to . File: +COMMENT (ignored) File: +DESC (ignored) As you can see, book.pdf will have been installed into /usr/share/doc/en_US.ISO8859-1/books/faq. If you do not want to use the packages then you will have to download the compressed files yourself, uncompress them, and then copy the appropriate documents into place. For example, the split HTML version of the FAQ, compressed using &man.gzip.1;, can be found in the doc/en_US.ISO8859-1/books/faq/book.html-split.tar.gz file. To download and uncompress that file you would have to do this. &prompt.root; fetch ftp://ftp.FreeBSD.org/pub/FreeBSD/doc/en_US.ISO8859-1/books/faq/book.html-split.tar.gz &prompt.root; gzip -d book.html-split.tar.gz &prompt.root; tar xvf book.html-split.tar You will be left with a collection of .html files. The main one is called index.html, which will contain the table of contents, introductory material, and links to the other parts of the document. You can then copy or move these to their final location as necessary. Where do I find info on the FreeBSD mailing lists? You can find full information in the Handbook entry on mailing-lists. Where do I find the FreeBSD Y2K info? You can find full information in the FreeBSD Y2K page. What FreeBSD news groups are available? You can find full information in the Handbook entry on newsgroups. Are there FreeBSD IRC (Internet Relay Chat) channels? Yes, most major IRC networks host a FreeBSD chat channel: Channel #FreeBSD on EFNet is a FreeBSD forum, but do not go there for tech support or try to get folks there to help you avoid the pain of reading man pages or doing your own research. It is a chat channel, first and foremost, and topics there are just as likely to involve sex, sports or nuclear weapons as they are FreeBSD. You Have Been Warned! Available at server irc.chat.org. Channel #FreeBSDhelp on EFNet is a channel dedicated to helping FreeBSD users. They are much more sympathetic to questions than #FreeBSD is. Channel #FreeBSD on DALNET is available at irc.dal.net in the US and irc.eu.dal.net in Europe. Channel #FreeBSD on UNDERNET is available at us.undernet.org in the US and eu.undernet.org in Europe. Since it is a help channel, be prepared to read the documents you are referred to. Channel #FreeBSD on HybNet. This channel is a help channel. A list of servers can be found on the HybNet web site. Each of these channels are distinct and are not connected to each other. Their chat styles also differ, so you may need to try each to find one suited to your chat style. As with all types of IRC traffic, if you are easily offended or cannot deal with lots of young people (and more than a few older ones) doing the verbal equivalent of jello wrestling, do not even bother with it. Where can I get commercial FreeBSD training and support? DaemonNews provides commercial training and support for FreeBSD. More information can be found at their BSD Mall site. FreeBSD Services Ltd provide commercial support for FreeBSD in the UK (as well as selling FreeBSD on DVD). See their web site for more information. The FreeBSD Mall provides commercial FreeBSD support. You can get more information at their web site. Any other organizations providing training and support should contact the project in order to be listed here. Nik Clayton
nik@FreeBSD.org
 Installation Which file do I download to get FreeBSD? Prior to release 3.1, you only needed one floppy image to install FreeBSD, namely floppies/boot.flp. However, since release 3.1 the Project has added out-of-the-box support for a wide variety of hardware, which takes up more space. For 3.x and later you need two floppy images: floppies/kernel.flp and floppies/mfsroot.flp. These images need to be copied onto floppies by tools like fdimage or &man.dd.1;. If you need to download the distributions yourself (for a DOS filesystem install, for instance), below are some recommendations for distributions to grab: bin/ manpages/ compat*/ doc/ src/ssys.* Full instructions on this procedure and a little bit more about installation issues in general can be found in the Handbook entry on installing FreeBSD. What do I do if the floppy images does not fit on a single floppy? A 3.5 inch (1.44MB) floppy can accommodate 1474560 bytes of data. The boot image is exactly 1474560 bytes in size. Common mistakes when preparing the boot floppy are: Not downloading the floppy image in binary mode when using FTP. Some FTP clients default their transfer mode to ascii and attempt to change any end-of-line characters received to match the conventions used by the client's system. This will almost invariably corrupt the boot image. Check the size of the downloaded boot image: if it is not exactly that on the server, then the download process is suspect. To workaround: type binary at the FTP command prompt after getting connected to the server and before starting the download of the image. Using the DOS copy command (or equivalent GUI tool) to transfer the boot image to floppy. Programs like copy will not work as the boot image has been created to be booted into directly. The image has the complete content of the floppy, track for track, and is not meant to be placed on the floppy as a regular file. You have to transfer it to the floppy raw, using the low-level tools (e.g. fdimage or rawrite) described in the installation guide to FreeBSD. Where are the instructions for installing FreeBSD? Installation instructions can be found in the Handbook entry on installing FreeBSD. What do I need in order to run FreeBSD? You will need a 386 or better PC, with 5 MB or more of RAM and at least 60 MB of hard disk space. It can run with a low end MDA graphics card but to run X11R6, a VGA or better video card is needed. See also I have only 4 MB of RAM. Can I install FreeBSD? FreeBSD 2.1.7 was the last version of FreeBSD that could be installed on a 4MB system. FreeBSD 2.2 and later needs at least 5MB to install on a new system. All versions of FreeBSD will run in 4MB of RAM, they just cannot run the installation program in 4MB. You can add extra memory for the install process, if you like, and then after the system is up and running, go back to 4MB. Or you could swap your disk into a system which has >4MB, install onto the disk and then swap it back. FreeBSD 2.1.7 will not install with 640 kB base + 3 MB extended memory. If your motherboard can remap some of the lost memory out of the 640kB to 1MB region, then you may still be able to get FreeBSD 2.1.7 up. Try to go into your BIOS setup and look for a remap option. Enable it. You may also have to disable ROM shadowing. It may be easier to get 4 more MB just for the install. Build a custom kernel with only the options you need and then remove the 4MB out. You can also install 2.0.5 and then upgrade your system to 2.1.7 with the upgrade option of the 2.1.7 installation program. After the installation, if you build a custom kernel, it will run in 4 MB. Someone has even successfully booted with 2 MB, although the system was almost unusable. How can I make my own custom install floppy? Currently there is no way to just make a custom install floppy. You have to cut a whole new release, which will include your install floppy. To make a custom release, follow the instructions in the Release Engineering article. Can I have more than one operating system on my PC? Have a look at the multi-OS page. Can Windows 95/98 co-exist with FreeBSD? Install Windows 95/98 first, after that FreeBSD. FreeBSD's boot manager will then manage to boot Win95/98 and FreeBSD. If you install Windows 95/98 second, it will boorishly overwrite your boot manager without even asking. If that happens, see the next section. Windows 95/98 killed my boot manager! How do I get it back? You can reinstall the boot manager FreeBSD comes with in one of three ways: Running DOS, go into the tools/ directory of your FreeBSD distribution and look for bootinst.exe. You run it like so: ...\TOOLS> bootinst.exe boot.bin and the boot manager will be reinstalled. Boot the FreeBSD boot floppy again and go to the Custom installation menu item. Choose Partition. Select the drive which used to contain your boot manager (likely the first one) and when you come to the partition editor for it, as the very first thing (e.g. do not make any changes) select (W)rite. This will ask for confirmation, say yes, and when you get the Boot Manager selection prompt, be sure to select Boot Manager. This will re-write the boot manager to disk. Now quit out of the installation menu and reboot off the hard disk as normal. Boot the FreeBSD boot floppy (or CDROM) and choose the Fixit menu item. Select either the Fixit floppy or CDROM #2 (the live filesystem option) as appropriate and enter the fixit shell. Then execute the following command: Fixit# fdisk -B -b /boot/boot0 bootdevice substituting bootdevice for your real boot device such as ad0 (first IDE disk), ad4 (first IDE disk on auxiliary controller), da0 (first SCSI disk), etc. My A, T, or X series IBM Thinkpad locks up when I first booted up my FreeBSD installation. How can I solve this? A bug in early revisions of IBM's BIOS on these machines mistakenly identifies the FreeBSD partition as a potential FAT suspend-to-disk partition. When the BIOS tries to parse the FreeBSD partition it hangs. According to IBMIn an e-mail from Keith Frechette kfrechet@us.ibm.com., the following model/BIOS release numbers incorporate the fix. Model BIOS revision T20 IYET49WW or later T21 KZET22WW or later A20p IVET62WW or later A20m IWET54WW or later A21p KYET27WW or later A21m KXET24WW or later A21e KUET30WW It has been reported that later IBM BIOS revisions may have reintroduced the bug. This message from Jacques Vidrine to the &a.mobile; describes a procedure which may work if your newer IBM laptop does not boot FreeBSD properly, and you can upgrade or downgrade the BIOS.. If you have an earlier BIOS, and upgrading is not an option a workaround is to install FreeBSD, change the partition ID FreeBSD uses, and install new boot blocks that can handle the different partition ID. First, you will need to restore the machine to a state where it can get through its self-test screen. Doing this requires powering up the machine without letting it find a FreeBSD partition on its primary disk. One way is to remove the hard disk and temporarily move it to an older ThinkPad (such as a ThinkPad 600) or a desktop PC with an appropriate conversion cable. Once it is there, you can delete the FreeBSD partition and move the hard disk back. The ThinkPad should now be in a bootable state again. With the machine functional again, you can use the workaround procedure described here to get a working FreeBSD installation. Download boot1 and boot2 from http://people.FreeBSD.org/~bmah/ThinkPad/. Put these files somewhere you will be able to retrieve them later. Install FreeBSD as normal on to the ThinkPad. Do not use Dangerously Dedicated mode. Do not reboot when the install has finished. Either switch to the Emergency Holographic Shell (ALT F4) or start a fixit shell. Use &man.fdisk.8; to change the FreeBSD partition ID from 165 to 166 (this is the type used by OpenBSD). Bring the boot1 and boot2 files to the local filesystem. Use &man.disklabel.8; to write boot1 and boot2 to your FreeBSD slice. &prompt.root; disklabel -B -b boot1 -s boot2 ad0sn n is the number of the slice where you installed FreeBSD. Reboot. At the boot prompt you will be given the option of booting OpenBSD. This will actually boot FreeBSD. Getting this to work in the case where you want to dual boot OpenBSD and FreeBSD on the same laptop is left as an exercise for the reader. Can I install on a disk with bad blocks? Prior to 3.0, FreeBSD included a utility known as bad144, which automatically remapped bad blocks. Because modern IDE drives perform this function themselves, bad144 has been removed from the FreeBSD source tree. If you wish to install FreeBSD 3.0 or later, we strongly suggest you purchase a newer disk drive. If you do not wish to do this, you must run FreeBSD 2.x. If you are seeing bad block errors with a modern IDE drive, chances are the drive is going to die very soon (the drive's internal remapping functions are no longer sufficient to fix the bad blocks, which means the disk is heavily corrupted); we suggest you buy a new hard drive. If you have a SCSI drive with bad blocks, see this answer. I have just upgraded from 3.X to 4.X, and my first boot failed with bad sector table not supported FreeBSD 3.X and earlier supported bad144, which automatically remapped bad blocks. FreeBSD 4.X and later do not support this, as modern IDE drives include this functionality. See this question for more information. To fix this after an upgrade, you need to physically place the drive in a working system and use &man.disklabel.8; as discussed in the following questions. How do I tell if a drive has bad144 information on it before I try to upgrade to FreeBSD 4.0 and it fails? Use &man.disklabel.8; for this. disklabel -r drive device will give you the contents of your disk label. Look for a flags field. If you see flags: badsect, this drive is using bad144. For example, the following drive has bad144 enabled.: &prompt.root; disklabel -r wd0 # /dev/rwd0c: type: ESDI disk: wd0s1 label: flags: badsect bytes/sector: 512 sectors/track: 63 How do I remove bad144 from my pre-4.X system so I can upgrade safely? Use disklabel -e -rwd0 to edit the disklabel in place. Just remove the word badsect from the flags field, save, and exit. The bad144 file will still take up some space on your drive, but the disk itself will be usable. We still recommend you purchase a new disk if you have a large number of bad blocks. Strange things happen when I boot the install floppy! What is happening? If you are seeing things like the machine grinding to a halt or spontaneously rebooting when you try to boot the install floppy, here are three questions to ask yourself:- Did you use a new, freshly-formatted, error-free floppy (preferably a brand-new one straight out of the box, as opposed to the magazine cover disk that has been lying under the bed for the last three years)? Did you download the floppy image in binary (or image) mode? (do not be embarrassed, even the best of us have accidentally downloaded a binary file in ASCII mode at least once!) If you are using Windows95 or Win98 did you run fdimage or rawrite in pure DOS mode? These operating systems can interfere with programs that write directly to hardware, which the disk creation program does; even running it inside a DOS shell in the GUI can cause this problem. There have also been reports of Netscape causing problems when downloading the boot floppy, so it is probably best to use a different FTP client if you can. I booted from my ATAPI CDROM, but the install program says no CDROM is found. Where did it go? The usual cause of this problem is a mis-configured CDROM drive. Many PCs now ship with the CDROM as the slave device on the secondary IDE controller, with no master device on that controller. This is illegal according to the ATAPI specification, but Windows plays fast and loose with the specification, and the BIOS ignores it when booting. This is why the BIOS was able to see the CDROM to boot from it, but why FreeBSD cannot see it to complete the install. Reconfigure your system so that the CDROM is either the master device on the IDE controller it is attached to, or make sure that it is the slave on an IDE controller that also has a master device. Can I install on my laptop over PLIP (Parallel Line IP)? Yes. Use a standard Laplink cable. If necessary, you can check out the PLIP section of the Handbook for details on parallel port networking. If you are running FreeBSD 3.X or earlier, also look at the Mobile Computing page. Which geometry should I use for a disk drive? By the geometry of a disk, we mean the number of cylinders, heads and sectors/track on a disk. We will refer to this as C/H/S for convenience. This is how the PC's BIOS works out which area on a disk to read/write from. This causes a lot of confusion among new system administrators. First of all, the physical geometry of a SCSI drive is totally irrelevant, as FreeBSD works in term of disk blocks. In fact, there is no such thing as the physical geometry, as the sector density varies across the disk. What manufacturers claim is the physical geometry is usually the geometry that they have determined wastes the least space. For IDE disks, FreeBSD does work in terms of C/H/S, but all modern drives internally convert this into block references. All that matters is the logical geometry. This is the answer that the BIOS gets when it asks the drive what is your geometry? It then uses this geometry to access the disk. As FreeBSD uses the BIOS when booting, it is very important to get this right. In particular, if you have more than one operating system on a disk, they must all agree on the geometry. Otherwise you will have serious problems booting! For SCSI disks, the geometry to use depends on whether extended translation support is turned on in your controller (this is often referred to as support for DOS disks >1GB or something similar). If it is turned off, then use N cylinders, 64 heads and 32 sectors/track, where N is the capacity of the disk in MB. For example, a 2GB disk should pretend to have 2048 cylinders, 64 heads and 32 sectors/track. If it is turned on (it is often supplied this way to get around certain limitations in MSDOS) and the disk capacity is more than 1GB, use M cylinders, 63 sectors per track (not 64), and 255 heads, where 'M' is the disk capacity in MB divided by 7.844238 (!). So our example 2GB drive would have 261 cylinders, 63 sectors per track and 255 heads. If you are not sure about this, or FreeBSD fails to detect the geometry correctly during installation, the simplest way around this is usually to create a small DOS partition on the disk. The BIOS should then detect the correct geometry, and you can always remove the DOS partition in the partition editor if you do not want to keep it. You might want to leave it around for programming network cards and the like, however. Alternatively, there is a freely available utility distributed with FreeBSD called pfdisk.exe. You can find it in the tools subdirectory on the FreeBSD CDROM or on the various FreeBSD FTP sites. This program can be used to work out what geometry the other operating systems on the disk are using. You can then enter this geometry in the partition editor. Are there any restrictions on how I divide the disk up? Yes. You must make sure that your root partition is below 1024 cylinders so the BIOS can boot the kernel from it. (Note that this is a limitation in the PC's BIOS, not FreeBSD). For a SCSI drive, this will normally imply that the root partition will be in the first 1024MB (or in the first 4096MB if extended translation is turned on - see previous question). For IDE, the corresponding figure is 504MB. Is FreeBSD compatible with any disk managers? FreeBSD recognizes the Ontrack Disk Manager and makes allowances for it. Other disk managers are not supported. If you just want to use the disk with FreeBSD you do not need a disk manager. Just configure the disk for as much space as the BIOS can deal with (usually 504 megabytes), and FreeBSD should figure out how much space you really have. If you are using an old disk with an MFM controller, you may need to explicitly tell FreeBSD how many cylinders to use. If you want to use the disk with FreeBSD and another operating system, you may be able to do without a disk manager: just make sure the FreeBSD boot partition and the slice for the other operating system are in the first 1024 cylinders. If you are reasonably careful, a 20 megabyte boot partition should be plenty. When I boot FreeBSD I get Missing Operating System. What is happening? This is classically a case of FreeBSD and DOS or some other OS conflicting over their ideas of disk geometry. You will have to reinstall FreeBSD, but obeying the instructions given above will almost always get you going. Why can I not get past the boot manager's F? prompt? This is another symptom of the problem described in the preceding question. Your BIOS geometry and FreeBSD geometry settings do not agree! If your controller or BIOS supports cylinder translation (often marked as >1GB drive support), try toggling its setting and reinstalling FreeBSD. Do I need to install the complete sources? In general, no. However, we would strongly recommend that you install, at a minimum, the base source kit, which includes several of the files mentioned here, and the sys (kernel) source kit, which includes sources for the kernel. There is nothing in the system which requires the presence of the sources to operate, however, except for the kernel-configuration program &man.config.8;. With the exception of the kernel sources, our build structure is set up so that you can read-only mount the sources from elsewhere via NFS and still be able to make new binaries. (Because of the kernel-source restriction, we recommend that you not mount this on /usr/src directly, but rather in some other location with appropriate symbolic links to duplicate the top-level structure of the source tree.) Having the sources on-line and knowing how to build a system with them will make it much easier for you to upgrade to future releases of FreeBSD. To actually select a subset of the sources, use the Custom menu item when you are in the Distributions menu of the system installation tool. Do I need to build a kernel? Building a new kernel was originally pretty much a required step in a FreeBSD installation, but more recent releases have benefited from the introduction of a much friendlier kernel configuration tool. When at the FreeBSD boot prompt (boot:), use the flag and you will be dropped into a visual configuration screen which allows you to configure the kernel's settings for most common ISA cards. It is still recommended that you eventually build a new kernel containing just the drivers that you need, just to save a bit of RAM, but it is no longer a strict requirement for most systems. Should I use DES, Blowfish, or MD5 passwords and how do I specify which form my users receive? The default password format on FreeBSD is to use MD5-based passwords. These are believed to be more secure than the traditional Unix password format, which used a scheme based on the DES algorithm. DES passwords are still available if you need to share your password file with legacy operating systems which still use the less secure password format (they are available if you choose to install the crypto distribution in sysinstall, or by installing the crypto sources if building from source). Installing the crypto libraries will also allow you to use the Blowfish password format, which is more secure. Which password format to use for new passwords is controlled by the passwd_format login capability in /etc/login.conf, which takes values of des, blf (if these are available) or md5. See the &man.login.conf.5; manual page for more information about login capabilities. Why does the boot floppy start, but hang at the Probing Devices... screen? If you have a IDE Zip or Jaz drive installed, remove it and try again. The boot floppy can get confused by the drives. After the system is installed you can reconnect the drive. Hopefully this will be fixed in a later release. Why do I get a panic: can't mount root error when rebooting the system after installation? This error comes from confusion between the boot block's and the kernel's understanding of the disk devices. The error usually manifests on two-disk IDE systems, with the hard disks arranged as the master or single device on separate IDE controllers, with FreeBSD installed on the secondary IDE controller. The boot blocks think the system is installed on wd1 (the second BIOS disk) while the kernel assigns the first disk on the secondary controller device wd2. After the device probing, the kernel tries to mount what the boot blocks think is the boot disk, wd1, while it is really wd2, and fails. To fix the problem, do one of the following: For FreeBSD 3.3 and later, reboot the system and hit Enter at the Booting kernel in 10 seconds; hit [Enter] to interrupt prompt. This will drop you into the boot loader. Then type set root_disk_unit="disk_number" . disk_number will be 0 if FreeBSD is installed on the master drive on the first IDE controller, 1 if it is installed on the slave on the first IDE controller, 2 if it is installed on the master of the second IDE controller, and 3 if it is installed on the slave of the second IDE controller. Then type boot, and your system should boot correctly. To make this change permanent (ie so you do not have to do this every time you reboot or turn on your FreeBSD machine), put the line root_disk_unit="disk_number" in /boot/loader.conf.local . If using FreeBSD 3.2 or earlier, at the Boot: prompt, enter 1:wd(2,a)kernel and press Enter. If the system starts, then run the command echo "1:wd(2,a)kernel" > /boot.config to make it the default boot string. Move the FreeBSD disk onto the primary IDE controller, so the hard disks are consecutive. Rebuild your kernel, modify the wd configuration lines to read: controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr disk wd0 at wdc0 drive 0 # disk wd1 at wdc0 drive 1 # comment out this line controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr disk wd1 at wdc1 drive 0 # change from wd2 to wd1 disk wd2 at wdc1 drive 1 # change from wd3 to wd2 Install the new kernel. If you moved your disks and wish to restore the previous configuration, replace the disks in the desired configuration and reboot. Your system should boot successfully. What are the limits for memory? For memory, the limit is 4 gigabytes. This configuration has been tested, see wcarchive's configuration for more details. If you plan to install this much memory into a machine, you need to be careful. You will probably want to use ECC memory and to reduce capacitive loading use 9 chip memory modules versus 18 chip memory modules. What are the limits for ffs filesystems? For ffs filesystems, the maximum theoretical limit is 8 terabytes (2G blocks), or 16TB for the default block size of 8K. In practice, there is a soft limit of 1 terabyte, but with modifications filesystems with 4 terabytes are possible (and exist). The maximum size of a single ffs file is approximately 1G blocks (4TB) if the block size is 4K. Maximum file sizes fs block size 2.2.7-stable 3.0-current works should work 4K 4T-1 4T-1 4T-1 >4T 8K >32G 8T-1 >32G 32T-1 16K >128G 16T-1 >128G 32T-1 32K >512G 32T-1 >512G 64T-1 64K >2048G 64T-1 >2048G 128T-1
When the fs block size is 4K, triple indirect blocks work and everything should be limited by the maximum fs block number that can be represented using triple indirect blocks (approx. 1K^3 + 1K^2 + 1K), but everything is limited by a (wrong) limit of 1G-1 on fs block numbers. The limit on fs block numbers should be 2G-1. There are some bugs for fs block numbers near 2G-1, but such block numbers are unreachable when the fs block size is 4K. For block sizes of 8K and larger, everything should be limited by the 2G-1 limit on fs block numbers, but is actually limited by the 1G-1 limit on fs block numbers, except under -STABLE triple indirect blocks are unreachable, so the limit is the maximum fs block number that can be represented using double indirect blocks (approx. (blocksize/4)^2 + (blocksize/4)), and under -CURRENT exceeding this limit may cause problems. Using the correct limit of 2G-1 blocks does cause problems. Why do I get an error message, archsw.readin.failed after compiling and booting a new kernel? You can boot by specifying the kernel directly at the second stage, pressing any key when the | shows up before loader is started. More specifically, you have upgraded the source for your kernel, and installed a new kernel builtin from them without making world. This is not supported. Make world. How do I upgrade from 3.X -> 4.X? We strongly recommend that you use binary snapshots to do this. 4-STABLE snapshots are available at ftp://releng4.FreeBSD.org/. Because of the many changes between 3.X and 4-STABLE, a direct upgrade from source will probably fail. A source upgrade can be done, but only in stages. First, upgrade to the latest 3-STABLE (RELENG_3). Then upgrade to 4.1.1-RELEASE (RELENG_4_1_1_RELEASE). Finally, upgrade to 4-STABLE (RELENG_4). If you wish to upgrade using source, please see the FreeBSD Handbook for more information. Upgrading via source is never recommended for new users, and upgrading from 3.X to 4.X is even less so; make sure you have read the instructions carefully before attempting to upgrade via source. What are these security profiles? A security profile is a set of configuration options that attempts to achieve the desired ratio of security to convenience by enabling and disabling certain programs and other settings. For full details, see the Security Profile section of the Handbook's post-install chapter. Hardware compatibility Does FreeBSD support architectures other than the x86? Yes. FreeBSD currently runs on both Intel x86 and DEC (now Compaq) Alpha architectures. Interest has also been expressed in a port of FreeBSD to the SPARC architecture, join the &a.sparc; if you are interested in joining that project. Most recent additions to the list of upcoming platforms are IA-64 and PowerPC, join the &a.ia64; and/or the &a.ppc; for more information. For general discussion on new architectures, join the &a.platforms;. If your machine has a different architecture and you need something right now, we suggest you look at NetBSD or OpenBSD. I want to get a piece of hardware for my FreeBSD system. Which model/brand/type is best? This is discussed continually on the FreeBSD mailing lists. Since hardware changes so quickly, however, we expect this. We still strongly recommend that you read through the Hardware Notes and search the mailing list archives before asking about the latest and greatest hardware. Chances are a discussion about the type of hardware you are looking for took place just last week. If you are looking for a laptop, check the FreeBSD-mobile mailing list archives. Otherwise, you probably want the archives for FreeBSD-questions, or possibly a specific mailing list for a particular hardware type. What kind of hard drives does FreeBSD support? FreeBSD supports EIDE and SCSI drives (with a compatible controller; see the next section), and all drives using the original Western Digital interface (MFM, RLL, ESDI, and of course IDE). A few ESDI controllers that use proprietary interfaces may not work: stick to WD1002/3/6/7 interfaces and clones. Which SCSI controllers are supported? See the complete list in the current Hardware Notes. Which CDROM drives are supported by FreeBSD? Any SCSI drive connected to a supported controller is supported. The following proprietary CDROM interfaces are also supported: Mitsumi LU002 (8bit), LU005 (16bit) and FX001D (16bit 2x Speed). Sony CDU 31/33A Sound Blaster Non-SCSI CDROM Matsushita/Panasonic CDROM ATAPI compatible IDE CDROMs All non-SCSI cards are known to be extremely slow compared to SCSI drives, and some ATAPI CDROMs may not work. As of 2.2 the FreeBSD CDROM from the FreeBSD Mall supports booting directly from the CD. Which CD-RW drives are supported by FreeBSD? FreeBSD supports any ATAPI-compatible IDE CD-R or CD-RW drive. For FreeBSD versions 4.0 and later, see the man page for &man.burncd.8;. For earlier FreeBSD versions, see the examples in /usr/share/examples/atapi. FreeBSD also supports any SCSI CD-R or CD-RW drives. Install and use the cdrecord command from the ports or packages system, and make sure that you have the pass device compiled in your kernel. Does FreeBSD support ZIP drives? FreeBSD supports the SCSI ZIP drive out of the box, of course. The ZIP drive can only be set to run at SCSI target IDs 5 or 6, but if your SCSI host adapter's BIOS supports it you can even boot from it. It is not clear which host adapters support booting from targets other than 0 or 1, so you will have to consult your adapter's documentation if you would like to use this feature. ATAPI (IDE) Zip drives are supported in FreeBSD 2.2.6 and later releases. FreeBSD has contained support for Parallel Port Zip Drives since version 3.0. If you are using a sufficiently up to date version, then you should check that your kernel contains the scbus0, da0, ppbus0, and vp0 drivers (the GENERIC kernel contains everything except vp0). With all these drivers present, the Parallel Port drive should be available as /dev/da0s4. Disks can be mounted using mount /dev/da0s4 /mnt OR (for dos disks) mount_msdos /dev/da0s4 /mnt as appropriate. Also check out the FAQ on removable drives later in this chapter, and the note on formattingin the Administration chapter. Does FreeBSD support JAZ, EZ and other removable drives? Apart from the IDE version of the EZ drive, these are all SCSI devices, so they should all look like SCSI disks to FreeBSD, and the IDE EZ should look like an IDE drive. I am not sure how well FreeBSD supports changing the media out while running. You will of course need to dismount the drive before swapping media, and make sure that any external units are powered on when you boot the system so FreeBSD can see them. See this note on formatting. Which multi-port serial cards are supported by FreeBSD? There is a list of these in the Miscellaneous devices section of the handbook. Some unnamed clone cards have also been known to work, especially those that claim to be AST compatible. Check the &man.sio.4; man page to get more information on configuring such cards. Does FreeBSD support my USB keyboard? USB device support was added to FreeBSD 3.1. However, it is still in preliminary state and may not always work as of version 3.2. If you want to experiment with the USB keyboard support, follow the procedure described below. Use FreeBSD 3.2 or later. Add the following lines to your kernel configuration file, and rebuild the kernel. device uhci device ohci device usb device ukbd options KBD_INSTALL_CDEV In versions of FreeBSD before 4.0, use this instead: controller uhci0 controller ohci0 controller usb0 controller ukbd0 options KBD_INSTALL_CDEV Go to the /dev directory and create device nodes as follows: &prompt.root; cd /dev &prompt.root; ./MAKEDEV kbd0 kbd1 Edit /etc/rc.conf and add the following lines: usbd_enable="YES" usbd_flags="" After the system is rebooted, the AT keyboard becomes /dev/kbd0 and the USB keyboard becomes /dev/kbd1, if both are connected to the system. If there is the USB keyboard only, it will be /dev/ukbd0. If you want to use the USB keyboard in the console, you have to explicitly tell the console driver to use the existing USB keyboard. This can be done by running the following command as a part of system initialization. &prompt.root; kbdcontrol -k /dev/kbd1 < /dev/ttyv0 > /dev/null Note that if the USB keyboard is the only keyboard, it is accessed as /dev/kbd0, thus, the command should look like: &prompt.root; kbdcontrol -k /dev/kbd0 < /dev/ttyv0 > /dev/null /etc/rc.i386 is a good place to add the above command. Once this is done, the USB keyboard should work in the X environment as well without any special settings. Hot-plugging and unplugging of the USB keyboard may not work quite right yet. It is a good idea to connect the keyboard before you start the system and leave it connected until the system is shutdown to avoid troubles. See the &man.ukbd.4; man page for more information. I have an unusual bus mouse. How do I set it up? FreeBSD supports the bus mouse and the InPort bus mouse from such manufactures as Microsoft, Logitech and ATI. The bus device driver is compiled in the GENERIC kernel by default in FreeBSD versions 2.X, but not included in version 3.0 or later. If you are building a custom kernel with the bus mouse driver, make sure to add the following line to the kernel config file In FreeBSD 3.0 or before, add: device mse0 at isa? port 0x23c tty irq5 vector mseintr In FreeBSD 3.X, the line should be: device mse0 at isa? port 0x23c tty irq5 And in FreeBSD 4.X and later, the line should read: device mse0 at isa? port 0x23c irq5 Bus mice usually comes with dedicated interface cards. These cards may allow you to set the port address and the IRQ number other than shown above. Refer to the manual of your mouse and the &man.mse.4; man page for more information. How do I use my PS/2 (mouse port or keyboard) mouse? If you are running a post-2.2.5 version of FreeBSD, the necessary driver, psm, is included and enabled in the kernel. The kernel should detect your PS/2 mouse at boot time. If you are running a previous but relatively recent version of FreeBSD (2.1.x or better) then you can simply enable it in the kernel configuration menu at installation time, otherwise later with at the boot: prompt. It is disabled by default, so you will need to enable it explicitly. If you are running an older version of FreeBSD then you will have to add the following lines to your kernel configuration file and compile a new kernel. In FreeBSD 3.0 or earlier, the line should be: device psm0 at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr In FreeBSD 3.1 or later, the line should be: device psm0 at isa? tty irq 12 In FreeBSD 4.0 or later, the line should be: device psm0 at atkbdc? irq 12 See the Handbook entry on configuring the kernel if you have no experience with building kernels. Once you have a kernel detecting psm0 correctly at boot time, make sure that an entry for psm0 exists in /dev. You can do this by typing: &prompt.root; cd /dev; sh MAKEDEV psm0 when logged in as root. Is it possible to make use of a mouse in any way outside the X Window system? If you are using the default console driver, syscons, you can use a mouse pointer in text consoles to cut & paste text. Run the mouse daemon, moused, and turn on the mouse pointer in the virtual console: &prompt.root; moused -p /dev/xxxx -t yyyy &prompt.root; vidcontrol -m on Where xxxx is the mouse device name and yyyy is a protocol type for the mouse. See the &man.moused.8; man page for supported protocol types. You may wish to run the mouse daemon automatically when the system starts. In version 2.2.1, set the following variables in /etc/sysconfig. mousedtype="yyyy" mousedport="xxxx" mousedflags="" In versions 2.2.2 to 3.0, set the following variables in /etc/rc.conf. moused_type="yyyy" moused_port="xxxx" moused_flags="" In 3.1 and later, assuming you have a PS/2 mouse, all you need to is add moused_enable="YES" to /etc/rc.conf. In addition, if you would like to be able to use the mouse daemon on all virtual terminals instead of just console at boot-time, add the following to /etc/rc.conf. allscreens_flags="-m on" Staring from FreeBSD 2.2.6, the mouse daemon is capable of determining the correct protocol type automatically unless the mouse is a relatively old serial mouse model. Specify auto the protocol to invoke automatic detection. When the mouse daemon is running, access to the mouse needs to be coordinated between the mouse daemon and other programs such as the X Window. Refer to another section on this issue. How do I cut and paste text with mouse in the text console? Once you get the mouse daemon running (see previous section), hold down the button 1 (left button) and move the mouse to select a region of text. Then, press the button 2 (middle button) or the button 3 (right button) to paste it at the text cursor. In versions 2.2.6 and later, pressing the button 2 will paste the text. Pressing the button 3 will extend the selected region of text. If your mouse does not have the middle button, you may wish to emulate it or remap buttons using moused options. See the &man.moused.8; man page for details. Does FreeBSD support any USB mice? Preliminary USB device support was added to FreeBSD 3.1. It did not always work through early versions of 3.X. As of FreeBSD 4.0, USB devices should work out of the box. If you want to experiment with the USB mouse support under FreeBSD 3.X, follow the procedure described below. Use FreeBSD 3.2 or later. Add the following lines to your kernel configuration file, and rebuild the kernel. device uhci device ohci device usb device ums In versions of FreeBSD before 4.0, use this instead: controller uhci0 controller ohci0 controller usb0 device ums0 Go to the /dev directory and create a device node as follows: &prompt.root; cd /dev &prompt.root; ./MAKEDEV ums0 Edit /etc/rc.conf and add the following lines: moused_enable="YES" moused_type="auto" moused_port="/dev/ums0" moused_flags="" usbd_enable="YES" usbd_flags="" See the previous section for more detailed discussion on moused. In order to use the USB mouse in the X session, edit XF86Config. If you are using XFree86 3.3.2 or later, be sure to have the following lines in the Pointer section: Device "/dev/sysmouse" Protocol "Auto" If you are using earlier versions of XFree86, be sure to have the following lines in the Pointer section: Device "/dev/sysmouse" Protocol "SysMouse" Refer to another section on the mouse support in the X environment. Hot-plugging and unplugging of the USB mouse may not work quite right yet. It is a good idea connect the mouse before you start the system and leave it connected until the system is shutdown to avoid trouble. My mouse has a fancy wheel and buttons. Can I use them in FreeBSD? The answer is, unfortunately, It depends. These mice with additional features require specialized driver in most cases. Unless the mouse device driver or the user program has specific support for the mouse, it will act just like a standard two, or three button mouse. For the possible usage of wheels in the X Window environment, refer to that section. Why does my wheel-equipped PS/2 mouse cause my mouse cursor to jump around the screen? The PS/2 mouse driver psm in FreeBSD versions 3.2 or earlier has difficulty with some wheel mice, including Logitech model M-S48 and its OEM siblings. Apply the following patch to /sys/i386/isa/psm.c and rebuild the kernel. Index: psm.c =================================================================== RCS file: /src/CVS/src/sys/i386/isa/Attic/psm.c,v retrieving revision 1.60.2.1 retrieving revision 1.60.2.2 diff -u -r1.60.2.1 -r1.60.2.2 --- psm.c 1999/06/03 12:41:13 1.60.2.1 +++ psm.c 1999/07/12 13:40:52 1.60.2.2 @@ -959,14 +959,28 @@ sc->mode.packetsize = vendortype[i].packetsize; /* set mouse parameters */ +#if 0 + /* + * A version of Logitech FirstMouse+ won't report wheel movement, + * if SET_DEFAULTS is sent... Don't use this command. + * This fix was found by Takashi Nishida. + */ i = send_aux_command(sc->kbdc, PSMC_SET_DEFAULTS); if (verbose >= 2) printf("psm%d: SET_DEFAULTS return code:%04x\n", unit, i); +#endif if (sc->config & PSM_CONFIG_RESOLUTION) { sc->mode.resolution = set_mouse_resolution(sc->kbdc, - (sc->config & PSM_CONFIG_RESOLUTION) - 1); + (sc->config & PSM_CONFIG_RESOLUTION) - 1); + } else if (sc->mode.resolution >= 0) { + sc->mode.resolution + = set_mouse_resolution(sc->kbdc, sc->dflt_mode.resolution); + } + if (sc->mode.rate > 0) { + sc->mode.rate = set_mouse_sampling_rate(sc->kbdc, sc->dflt_mode.rate); } + set_mouse_scaling(sc->kbdc, 1); /* request a data packet and extract sync. bits */ if (get_mouse_status(sc->kbdc, stat, 1, 3) < 3) { Versions later than 3.2 should be all right. How do I use the mouse/trackball/touchpad on my laptop? Please refer to the answer to the previous question. Also check out the Mobile Computing page. What types of tape drives are supported? FreeBSD supports SCSI and QIC-36 (with a QIC-02 interface). This includes 8-mm (aka Exabyte) and DAT drives. Some of the early 8-mm drives are not quite compatible with SCSI-2, and may not work well with FreeBSD. Does FreeBSD support tape changers? FreeBSD 2.2 supports SCSI changers using the &man.ch.4; device and the &man.chio.1; command. The details of how you actually control the changer can be found in the &man.chio.1; man page. If you are not using AMANDA or some other product that already understands changers, remember that they only know how to move a tape from one point to another, so you need to keep track of which slot a tape is in, and which slot the tape currently in the drive needs to go back to. Which sound cards are supported by FreeBSD? FreeBSD supports the SoundBlaster, SoundBlaster Pro, SoundBlaster 16, Pro Audio Spectrum 16, AdLib and Gravis UltraSound sound cards. There is also limited support for MPU-401 and compatible MIDI cards. Cards conforming to the Microsoft Sound System specification are also supported through the pcm driver. This is only for sound! This driver does not support CDROMs, SCSI or joysticks on these cards, except for the SoundBlaster. The SoundBlaster SCSI interface and some non-SCSI CDROMs are supported, but you cannot boot off this device. Workarounds for no sound from es1370 with pcm driver? You can run the following command every time the machine booted up: &prompt.root; mixer pcm 100 vol 100 cd 100 Which network cards does FreeBSD support? See the Ethernet cards section of the handbook for a more complete list. I do not have a math co-processor - is that bad? This will only affect 386/486SX/486SLC owners - other machines will have one built into the CPU. In general this will not cause any problems, but there are circumstances where you will take a hit, either in performance or accuracy of the math emulation code (see the section on FP emulation). In particular, drawing arcs in X will be VERY slow. It is highly recommended that you buy a math co-processor; it is well worth it. Some math co-processors are better than others. It pains us to say it, but nobody ever got fired for buying Intel. Unless you are sure it works with FreeBSD, beware of clones. What other devices does FreeBSD support? See the Handbook for the list of other devices supported. Does FreeBSD support power management on my laptop? FreeBSD supports APM on certain machines. Please look in the LINT kernel config file, searching for the APM keyword. Further information can be found in &man.apm.4;. Why does my Micron system hang at boot time? Certain Micron motherboards have a non-conforming PCI BIOS implementation that causes grief when FreeBSD boots because PCI devices do not get configured at their reported addresses. Disable the Plug and Play Operating System flag in the BIOS to work around this problem. More information can be found at http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html#micron Why does FreeBSD not recognize my Adaptec SCSI controller card? The newer AIC789x series Adaptec chips are supported under the CAM SCSI framework which made its debut in 3.0. Patches against 2.2-STABLE are in ftp://ftp.FreeBSD.org/pub/FreeBSD/development/cam/. A CAM-enhanced boot floppy is available at http://people.FreeBSD.org/~abial/cam-boot/. In both cases read the README before beginning. Why is FreeBSD not finding my internal Plug & Play modem? You will need to add the modem's PnP ID to the PnP ID list in the serial driver. To enable Plug & Play support, compile a new kernel with controller pnp0 in the configuration file, then reboot the system. The kernel will print the PnP IDs of all the devices it finds. Copy the PnP ID from the modem to the table in /sys/i386/isa/sio.c, at about line 2777. Look for the string SUP1310 in the structure siopnp_ids[] to find the table. Build the kernel again, install, reboot, and your modem should be found. You may have to manually configure the PnP devices using the pnp command in the boot-time configuration with a command like pnp 1 0 enable os irq0 3 drq0 0 port0 0x2f8 to make the modem show. Does FreeBSD support software modems, such as Winmodems? FreeBSD supports many software modems via add-on software. The comms/ltmdm port adds support for modems based on the very popular Lucent LT chipset. The comms/mwavem port supports the modem in IBM Thinkpad 600 and 700 laptops. You cannot install FreeBSD via a software modem; this software must be installed after the OS is installed. How do I get the boot: prompt to show on the serial console? Build a kernel with options COMCONSOLE. Create /boot.config and place as the only text in the file. Unplug the keyboard from the system. See /usr/src/sys/i386/boot/biosboot/README.serial for information. Why does my 3Com PCI network card not work with my Micron computer? Certain Micron motherboards have a non-conforming PCI BIOS implementation that does not configure PCI devices at the addresses reported. This causes grief when FreeBSD boots. To work around this problem, disable the Plug and Play Operating System flag in the BIOS. More information on this problem is available at URL: http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html#micron Does FreeBSD support Symmetric Multiprocessing (SMP)? SMP is supported in 3.0-STABLE and later releases only. SMP is not enabled in the GENERIC kernel, so you will have to recompile your kernel to enable SMP. Take a look at /sys/i386/conf/LINT to figure out what options to put in your kernel config file. The boot floppy hangs on a system with an ASUS K7V motherboard. How do I fix this? Go into the BIOS setup and disable the boot virus protection. Troubleshooting What do I do when I have bad blocks on my hard drive? With SCSI drives, the drive should be capable of re-mapping these automatically. However, many drives are shipped with this feature disabled, for some mysterious reason... To enable this, you will need to edit the first device page mode, which can be done on FreeBSD by giving the command (as root) &prompt.root; scsi -f /dev/rsd0c -m 1 -e -P 3 and changing the values of AWRE and ARRE from 0 to 1:- AWRE (Auto Write Reallocation Enbld): 1 ARRE (Auto Read Reallocation Enbld): 1 The following paragraphs were submitted by Ted Mittelstaedt tedm@toybox.placo.com: For IDE drives, any bad block is usually a sign of potential trouble. All modern IDE drives come with internal bad-block remapping turned on. All IDE hard drive manufacturers today offer extensive warranties and will replace drives with bad blocks on them. If you still want to attempt to rescue an IDE drive with bad blocks, you can attempt to download the IDE drive manufacturer's IDE diagnostic program, and run this against the drive. Sometimes these programs can be set to force the drive electronics to rescan the drive for bad blocks and lock them out. For ESDI, RLL and MFM drives, bad blocks are a normal part of the drive and are no sign of trouble, generally. With a PC, the disk drive controller card and BIOS handle the task of locking out bad sectors. This is fine for operating systems like DOS that use BIOS code to access the disk. However, FreeBSD's disk driver does not go through BIOS, therefore a mechanism, bad144, exists that replaces this functionality. bad144 only works with the wd driver (which means it is not supported in FreeBSD 4.0), it is NOT able to be used with SCSI. bad144 works by entering all bad sectors found into a special file. One caveat with bad144 - the bad block special file is placed on the last track of the disk. As this file may possibly contain a listing for a bad sector that would occur near the beginning of the disk, where the /kernel file might be located, it therefore must be accessible to the bootstrap program that uses BIOS calls to read the kernel file. This means that the disk with bad144 used on it must not exceed 1024 cylinders, 16 heads, and 63 sectors. This places an effective limit of 500MB on a disk that is mapped with bad144. To use bad144, simply set the Bad Block scanning to ON in the FreeBSD fdisk screen during the initial install. This works up through FreeBSD 2.2.7. The disk must have less than 1024 cylinders. It is generally recommended that the disk drive has been in operation for at least 4 hours prior to this to allow for thermal expansion and track wandering. If the disk has more than 1024 cylinders (such as a large ESDI drive) the ESDI controller uses a special translation mode to make it work under DOS. The wd driver understands about these translation modes, IF you enter the translated geometry with the set geometry command in fdisk. You must also NOT use the dangerously dedicated mode of creating the FreeBSD partition, as this ignores the geometry. Also, even though fdisk will use your overridden geometry, it still knows the true size of the disk, and will attempt to create a too large FreeBSD partition. If the disk geometry is changed to the translated geometry, the partition MUST be manually created with the number of blocks. A quick trick to use is to set up the large ESDI disk with the ESDI controller, boot it with a DOS disk and format it with a DOS partition. Then, boot the FreeBSD install and in the fdisk screen, read off and write down the blocksize and block numbers for the DOS partition. Then, reset the geometry to the same that DOS uses, delete the DOS partition, and create a cooperative FreeBSD partition using the blocksize you recorded earlier. Then, set the partition bootable and turn on bad block scanning. During the actual install, bad144 will run first, before any filesystems are created (you can view this with an AltF2). If it has any trouble creating the badsector file, you have set too large a disk geometry - reboot the system and start all over again (including repartitioning and reformatting with DOS). If remapping is enabled and you are seeing bad blocks, consider replacing the drive. The bad blocks will only get worse as time goes on. Why does FreeBSD not recognize my Bustek 742a EISA SCSI controller? This info is specific to the 742a but may also cover other Buslogic cards. (Bustek = Buslogic) There are 2 general versions of the 742a card. They are hardware revisions A-G, and revisions H - onwards. The revision letter is located after the Assembly number on the edge of the card. The 742a has 2 ROM chips on it, one is the BIOS chip and the other is the Firmware chip. FreeBSD does not care what version of BIOS chip you have but it does care about what version of firmware chip. Buslogic will send upgrade ROMs out if you call their tech support dept. The BIOS and Firmware chips are shipped as a matched pair. You must have the most current Firmware ROM in your adapter card for your hardware revision. The REV A-G cards can only accept BIOS/Firmware sets up to 2.41/2.21. The REV H- up cards can accept the most current BIOS/Firmware sets of 4.70/3.37. The difference between the firmware sets is that the 3.37 firmware supports round robin. The Buslogic cards also have a serial number on them. If you have an old hardware revision card you can call the Buslogic RMA department and give them the serial number and attempt to exchange the card for a newer hardware revision. If the card is young enough they will do so. FreeBSD 2.1 only supports Firmware revisions 2.21 onward. If you have a Firmware revision older than this your card will not be recognized as a Buslogic card. It may be recognized as an Adaptec 1540, however. The early Buslogic firmware contains an AHA1540 emulation mode. This is not a good thing for an EISA card, however. If you have an old hardware revision card and you obtain the 2.21 firmware for it, you will need to check the position of jumper W1 to B-C, the default is A-B. Why does FreeBSD not detect my HP Netserver's SCSI controller? This is basically a known problem. The EISA on-board SCSI controller in the HP Netserver machines occupies EISA slot number 11, so all the true EISA slots are in front of it. Alas, the address space for EISA slots >= 10 collides with the address space assigned to PCI, and FreeBSD's auto-configuration currently cannot handle this situation very well. So now, the best you can do is to pretend there is no address range clash :), by bumping the kernel option EISA_SLOTS to a value of 12. Configure and compile a kernel, as described in the Handbook entry on configuring the kernel. Of course, this does present you with a chicken-and-egg problem when installing on such a machine. In order to work around this problem, a special hack is available inside UserConfig. Do not use the visual interface, but the plain command-line interface there. Simply type eisa 12 quit at the prompt, and install your system as usual. While it is recommended you compile and install a custom kernel anyway. Hopefully, future versions will have a proper fix for this problem. You cannot use a dangerously dedicated disk with an HP Netserver. See this note for more info. What is going on with my CMD640 IDE controller? It is broken. It cannot handle commands on both channels simultaneously. There is a workaround available now and it is enabled automatically if your system uses this chip. For the details refer to the manual page of the disk driver (man 4 wd). If you are already running FreeBSD 2.2.1 or 2.2.2 with a CMD640 IDE controller and you want to use the second channel, build a new kernel with options "CMD640" enabled. This is the default for 2.2.5 and later. I keep seeing messages like ed1: timeout. What do these messages mean? This is usually caused by an interrupt conflict (e.g., two boards using the same IRQ). FreeBSD prior to 2.0.5R used to be tolerant of this, and the network driver would still function in the presence of IRQ conflicts. However, with 2.0.5R and later, IRQ conflicts are no longer tolerated. Boot with the -c option and change the ed0/de0/... entry to match your board. If you are using the BNC connector on your network card, you may also see device timeouts because of bad termination. To check this, attach a terminator directly to the NIC (with no cable) and see if the error messages go away. Some NE2000 compatible cards will give this error if there is no link on the UTP port or if the cable is disconnected. Why did my 3COM 3C509 card stop working for no apparent reason? This card has a bad habit of losing its configuration information. Refresh your card's settings with the DOS utility 3c5x9.exe. My parallel printer is ridiculously slow. What can I do? If the only problem is that the printer is terribly slow, try changing your printer port mode as discussed in the Printer Setup section of the Handbook. Why do my programs occasionally die with Signal 11 errors? Signal 11 errors are caused when your process has attempted to access memory which the operating system has not granted it access to. If something like this is happening at seemingly random intervals then you need to start investigating things very carefully. These problems can usually be attributed to either: If the problem is occurring only in a specific application that you are developing yourself it is probably a bug in your code. If it is a problem with part of the base FreeBSD system, it may also be buggy code, but more often than not these problems are found and fixed long before us general FAQ readers get to use these bits of code (that is what -current is for). In particular, a dead giveaway that this is not a FreeBSD bug is if you see the problem when you are compiling a program, but the activity that the compiler is carrying out changes each time. For example, suppose you are running make buildworld, and the compile fails while trying to compile ls.c into ls.o. If you then run make buildworld again, and the compile fails in the same place then this is a broken build -- try updating your sources and try again. If the compile fails elsewhere then this is almost certainly hardware. What you should do: In the first case you can use a debugger e.g. gdb to find the point in the program which is attempting to access a bogus address and then fix it. In the second case you need to verify that it is not your hardware at fault. Common causes of this include: Your hard disks might be overheating: Check the fans in your case are still working, as your disk (and perhaps other hardware might be overheating). The processor running is overheating: This might be because the processor has been overclocked, or the fan on the processor might have died. In either case you need to ensure that you have hardware running at what it is specified to run at, at least while trying to solve this problem. i.e. Clock it back to the default settings. If you are overclocking then note that it is far cheaper to have a slow system than a fried system that needs replacing! Also the wider community is not often sympathetic to problems on overclocked systems, whether you believe it is safe or not. Dodgy memory: If you have multiple memory SIMMS/DIMMS installed then pull them all out and try running the machine with each SIMM or DIMM individually and narrow the problem down to either the problematic DIMM/SIMM or perhaps even a combination. Over-optimistic Motherboard settings: In your BIOS settings, and some motherboard jumpers you have options to set various timings, mostly the defaults will be sufficient, but sometimes, setting the wait states on RAM too low, or setting the RAM Speed: Turbo option, or similar in the BIOS will cause strange behavior. A possible idea is to set to BIOS defaults, but it might be worth noting down your settings first! Unclean or insufficient power to the motherboard. If you have any unused I/O boards, hard disks, or CDROMs in your system, try temporarily removing them or disconnecting the power cable from them, to see if your power supply can manage a smaller load. Or try another power supply, preferably one with a little more power (for instance, if your current power supply is rated at 250 Watts try one rated at 300 Watts). You should also read the SIG11 FAQ (listed below) which has excellent explanations of all these problems, albeit from a Linux viewpoint. It also discusses how memory testing software or hardware can still pass faulty memory. Finally, if none of this has helped it is possible that you have just found a bug in FreeBSD, and you should follow the instructions to send a problem report. There is an extensive FAQ on this at the SIG11 problem FAQ My system crashes with either Fatal trap 12: page fault in kernel mode, or panic:, and spits out a bunch of information. What should I do? The FreeBSD developers are very interested in these errors, but need some more information than just the error you see. Copy your full crash message. Then consult the FAQ section on kernel panics, build a debugging kernel, and get a backtrace. This might sound difficult, but you do not need any programming skills; you just have to follow the instructions. Why does the screen go black and lose sync when I boot? This is a known problem with the ATI Mach 64 video card. The problem is that this card uses address 2e8, and the fourth serial port does too. Due to a bug (feature?) in the &man.sio.4; driver it will touch this port even if you do not have the fourth serial port, and even if you disable sio3 (the fourth port) which normally uses this address. Until the bug has been fixed, you can use this workaround: Enter at the boot prompt. (This will put the kernel into configuration mode). Disable sio0, sio1, sio2 and sio3 (all of them). This way the sio driver does not get activated -> no problems. Type exit to continue booting. If you want to be able to use your serial ports, you will have to build a new kernel with the following modification: in /usr/src/sys/i386/isa/sio.c find the one occurrence of the string 0x2e8 and remove that string and the preceding comma (keep the trailing comma). Now follow the normal procedure of building a new kernel. Even after applying these workarounds, you may still find that the X Window System does not work properly. If this is the case, make sure that the XFree86 version you are using is at least XFree86 3.3.3 or higher. This version and upwards has built-in support for the Mach64 cards and even a dedicated X server for those cards. Why does FreeBSD only use 64 MB of RAM when my system has 128 MB of RAM installed? Due to the manner in which FreeBSD gets the memory size from the BIOS, it can only detect 16 bits worth of Kbytes in size (65535 Kbytes = 64MB) (or less... some BIOSes peg the memory size to 16M). If you have more than 64MB, FreeBSD will attempt to detect it; however, the attempt may fail. To work around this problem, you need to use the kernel option specified below. There is a way to get complete memory information from the BIOS, but we do not have room in the bootblocks to do it. Someday when lack of room in the bootblocks is fixed, we will use the extended BIOS functions to get the full memory information...but for now we are stuck with the kernel option. options "MAXMEM=n" Where n is your memory in Kilobytes. For a 128 MB machine, you would want to use 131072. Why does FreeBSD 2.0 panic with kmem_map too small!? The message may also be mb_map too small! The panic indicates that the system ran out of virtual memory for network buffers (specifically, mbuf clusters). You can increase the amount of VM available for mbuf clusters by adding: options "NMBCLUSTERS=n" to your kernel config file, where n is a number in the range 512-4096, depending on the number of concurrent TCP connections you need to support. I would recommend trying 2048 - this should get rid of the panic completely. You can monitor the number of mbuf clusters allocated/in use on the system with netstat -m (see &man.netstat.1;). The default value for NMBCLUSTERS is 512 + MAXUSERS * 16. Why do I get the error /kernel: proc: table is full? The FreeBSD kernel will only allow a certain number of processes to exist at one time. The number is based on the MAXUSERS option in the kernel configuration. MAXUSERS also affects various other in-kernel limits, such as network buffers (see this earlier question). If your machine is heavily loaded, you probably want to increase MAXUSERS. This will increase these other system limits in addition to the maximum number of processes. After FreeBSD 4.4, MAXUSERS became a tunable value that could be set with kern.maxusers in /boot/loader.conf. In earlier versions of FreeBSD, you need to adjust MAXUSERS in your kernel configuration. If your machine is lightly loaded, and you are simply running a very large number of processes, you can adjust this with the kern.maxproc sysctl. If these processes are being run by a single user, you will also need to adjust kern.maxprocperuid to be one less than your new kern.maxproc value. (It must be at least one less because one system program, &man.init.8;, must always be running.) To make a sysctl permanent across reboots, set this in /etc/sysctl.conf in recent versions of FreeBSD, or /etc/rc.local in older versions. Why do I get an error reading CMAP busy when rebooting with a new kernel? The logic that attempts to detect an out of date /var/db/kvm_*.db files sometimes fails and using a mismatched file can sometimes lead to panics. If this happens, reboot single-user and do: &prompt.root; rm /var/db/kvm_*.db What does the message ahc0: brkadrint, Illegal Host Access at seqaddr 0x0 mean? This is a conflict with an Ultrastor SCSI Host Adapter. During the boot process enter the kernel configuration menu and disable uha0, which is causing the problem. When I boot my system, I get the error ahc0: illegal cable configuration. My cabling is correct. What is going on? Your motherboard lacks the external logic to support automatic termination. Switch your SCSI BIOS to specify the correct termination for your configuration rather than automatic termination. The AIC7XXX driver cannot determine if the external logic for cable detection (and thus auto-termination) is available. The driver simply assumes that this support must exist if the configuration contained in the serial EEPROM is set to "automatic termination". Without the external cable detection logic the driver will often configure termination incorrectly, which can compromise the reliability of the SCSI bus. Why does Sendmail give me an error reading mail loops back to myself? This is answered in the sendmail FAQ as follows:- * I'm getting "Local configuration error" messages, such as: 553 relay.domain.net config error: mail loops back to myself 554 <user@domain.net>... Local configuration error How can I solve this problem? You have asked mail to the domain (e.g., domain.net) to be forwarded to a specific host (in this case, relay.domain.net) by using an MX record, but the relay machine does not recognize itself as domain.net. Add domain.net to /etc/mail/local-host-names (if you are using FEATURE(use_cw_file)) or add "Cw domain.net" to /etc/mail/sendmail.cf. The current version of the sendmail FAQ is no longer maintained with the sendmail release. It is however regularly posted to comp.mail.sendmail, comp.mail.misc, comp.mail.smail, comp.answers, and news.answers. You can also receive a copy via email by sending a message to mail-server@rtfm.mit.edu with the command send usenet/news.answers/mail/sendmail-faq as the body of the message. Why do full screen applications on remote machines misbehave? The remote machine may be setting your terminal type to something other than the cons25 terminal type required by the FreeBSD console. There are a number of possible work-arounds for this problem: After logging on to the remote machine, set your TERM shell variable to ansi or sco if the remote machine knows about these terminal types. Use a VT100 emulator like screen at the FreeBSD console. screen offers you the ability to run multiple concurrent sessions from one terminal, and is a neat program in its own right. Each screen window behaves like a VT100 terminal, so the TERM variable at the remote end should be set to vt100. Install the cons25 terminal database entry on the remote machine. The way to do this depends on the operating system on the remote machine. The system administration manuals for the remote system should be able to help you here. Fire up an X server at the FreeBSD end and login to the remote machine using an X based terminal emulator such as xterm or rxvt. The TERM variable at the remote host should be set to xterm or vt100. Why does my machine print calcru: negative time...? This can be caused by various hardware and/or software ailments relating to interrupts. It may be due to bugs but can also happen by nature of certain devices. Running TCP/IP over the parallel port using a large MTU is one good way to provoke this problem. Graphics accelerators can also get you here, in which case you should check the interrupt setting of the card first. A side effect of this problem are dying processes with the message SIGXCPU exceeded cpu time limit. For FreeBSD 3.0 and later from Nov 29, 1998 forward: If the problem cannot be fixed otherwise the solution is to set this sysctl variable: &prompt.root; sysctl -w kern.timecounter.method=1 This means a performance impact, but considering the cause of this problem, you probably will not notice. If the problem persists, keep the sysctl set to one and set the NTIMECOUNTER option in your kernel to increasingly large values. If by the time you have reached NTIMECOUNTER=20 the problem is not solved, interrupts are too hosed on your machine for reliable time keeping. I see pcm0 not found or my sound card is found as pcm1 but I have device pcm0 in my kernel config file. What is going on? This occurs in FreeBSD 3.x with PCI sound cards. The pcm0 device is reserved exclusively for ISA-based cards so, if you have a PCI card, then you will see this error, and your card will appear as pcm1. You cannot remove the warning by simply changing the line in the kernel config file to device pcm1 as this will result in pcm1 being reserved for ISA cards and your PCI card being found as pcm2 (along with the warning pcm1 not found). If you have a PCI sound card you will also have to make the snd1 device rather than snd0: &prompt.root; cd /dev &prompt.root; ./MAKEDEV snd1 This situation does not arise in FreeBSD 4.x as a lot of work has been done to make it more PnP-centric and the pcm0 device is no longer reserved exclusively for ISA cards Why is my PnP card no longer found (or found as unknown) since upgrading to FreeBSD 4.x? FreeBSD 4.x is now much more PnP-centric and this has had the side effect of some PnP devices (e.g. sound cards and internal modems) not working even though they worked under FreeBSD 3.x. The reasons for this behavior are explained by the following e-mail, posted to the freebsd-questions mailing list by Peter Wemm, in answer to a question about an internal modem that was no longer found after an upgrade to FreeBSD 4.x (the comments in [] have been added to clarify the context.
The PNP bios preconfigured it [the modem] and left it laying around in port space, so [in 3.x] the old-style ISA probes found it there. Under 4.0, the ISA code is much more PnP-centric. It was possible [in 3.x] for an ISA probe to find a stray device and then for the PNP device id to match and then fail due to resource conflicts. So, it disables the programmable cards first so this double probing cannot happen. It also means that it needs to know the PnP id's for supported PnP hardware. Making this more user tweakable is on the TODO list.
To get the device working again requires finding its PnP id and adding it to the list that the ISA probes use to identify PnP devices. This is obtained using &man.pnpinfo.8; to probe the device, for example this is the output from &man.pnpinfo.8; for an internal modem: &prompt.root; pnpinfo Checking for Plug-n-Play devices... Card assigned CSN #1 Vendor ID PMC2430 (0x3024a341), Serial Number 0xffffffff PnP Version 1.0, Vendor Version 0 Device Description: Pace 56 Voice Internal Plug & Play Modem Logical Device ID: PMC2430 0x3024a341 #0 Device supports I/O Range Check TAG Start DF I/O Range 0x3f8 .. 0x3f8, alignment 0x8, len 0x8 [16-bit addr] IRQ: 4 - only one type (true/edge) [more TAG lines elided] TAG End DF End Tag Successfully got 31 resources, 1 logical fdevs -- card select # 0x0001 CSN PMC2430 (0x3024a341), Serial Number 0xffffffff Logical device #0 IO: 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 0x03e8 IRQ 5 0 DMA 4 0 IO range check 0x00 activate 0x01 The information you require is in the Vendor ID line at the start of the output. The hexadecimal number in parentheses (0x3024a341 in this example) is the PnP id and the string immediately before this (PMC2430) is a unique ASCII id. This information needs adding to the file /usr/src/sys/isa/sio.c. You should first make a backup of sio.c just in case things go wrong. You will also need it to make the patch to submit with your PR (you are going to submit a PR, are you not?) then edit sio.c and search for the line static struct isa_pnp_id sio_ids[] = { then scroll down to find the correct place to add the entry for your device. The entries look like this, and are sorted on the ASCII Vendor ID string which should be included in the comment to the right of the line of code along with all (if it will fit) or part of the Device Description from the output of &man.pnpinfo.8;: {0x0f804f3f, NULL}, /* OZO800f - Zoom 2812 (56k Modem) */ {0x39804f3f, NULL}, /* OZO8039 - Zoom 56k flex */ {0x3024a341, NULL}, /* PMC2430 - Pace 56 Voice Internal Modem */ {0x1000eb49, NULL}, /* ROK0010 - Rockwell ? */ {0x5002734a, NULL}, /* RSS0250 - 5614Jx3(G) Internal Modem */ Add the hexadecimal Vendor ID for your device in the correct place, save the file, rebuild your kernel, and reboot. Your device should now be found as an sio device as it was under FreeBSD 3.x Why do I get the error nlist failed when running, for example, top or systat? The problem is that the application you are trying to run is looking for a specific kernel symbol, but, for whatever reason, cannot find it; this error stems from one of two problems: Your kernel and userland are not synchronized (i.e., you built a new kernel but did not do an installworld, or vice versa), and thus the symbol table is different from what the user application thinks it is. If this is the case, simply complete the upgrade process (see /usr/src/UPDATING for the correct sequence). You are not using /boot/loader to load your kernel, but doing it directly from boot2 (see &man.boot.8;). While there is nothing wrong with bypassing /boot/loader, it generally does a better job of making the kernel symbols available to user applications. Why does it take so long to connect to my computer via ssh or telnet? The symptom: there is a long delay between the time the TCP connection is established and the time when the client software asks for a password (or, in &man.telnet.1;'s case, when a login prompt appears). The problem: more likely than not, the delay is caused by the server software trying to resolve the client's IP address into a hostname. Many servers, including the Telnet and SSH servers that come with FreeBSD, do this in order to, among other things, store the hostname in a log file for future reference by the administrator. The remedy: if the problem occurs whenever you connect from your computer (the client) to any server, the problem is with the client; likewise, if the problem only occurs when someone connects to your computer (the server) the problem is with the server. If the problem is with the client, the only remedy is to fix the DNS so the server can resolve it. If this is on a local network, consider it a server problem and keep reading; conversely, if this is on the global Internet, you will most likely need to contact your ISP and ask them to fix it for you. If the problem is with the server, and this is on a local network, you need to configure the server to be able to resolve address-to-hostname queries for your local address range. See the &man.hosts.5; and &man.named.8; manual pages for more information. If this is on the global Internet, the problem may be that your server's resolver is not functioning correctly. To check, try to look up another host--say, www.yahoo.com. If it does not work, that is your problem. What does stray IRQ mean? Stray IRQs are indications of hardware IRQ glitches, mostly from hardware that removes its interrupt request in the middle of the interrupt request acknowledge cycle. One has three options for dealing with this: Live with the warnings. All except the first 5 per irq are suppressed anyway. Break the warnings by changing 5 to 0 in isa_strayintr() so that all the warnings are suppressed. Break the warnings by installing parallel port hardware that uses irq 7 and the PPP driver for it (this happens on most systems), and install an ide drive or other hardware that uses irq 15 and a suitable driver for it. Why does file: table is full show up repeatedly in dmesg? This error message indicates you have exhausted the number of available file descriptors on your system. Please see the kern.maxfiles section of the Tuning Kernel Limits section of the Handbook for a discussion and solution. Why does the clock on my laptop keep incorrect time? Your laptop has two or more clocks, and FreeBSD has chosen to use the wrong one. Run &man.dmesg.8;, and check for lines that contain Timecounter. The last line printed is the one that FreeBSD chose, and will almost certainly be TSC. &prompt.root; dmesg | grep Timecounter Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 595573479 Hz You can confirm this by checking the kern.timecounter.hardware &man.sysctl.3;. &prompt.root; sysctl kern.timecounter.hardware kern.timecounter.hardware: TSC The BIOS may modify the TSC clock—perhaps to change the speed of the processor when running from batteries, or going into a power saving mode, but FreeBSD is unaware of these adjustments, and appears to gain or lose time. In this example, the i8254 clock is also available, and can be selected by writing its name to the kern.timecounter.hardware &man.sysctl.3;. &prompt.root; sysctl -w kern.timecounter.hardware=i8254 kern.timecounter.hardware: TSC -> i8254 Your laptop should now start keeping more accurate time. To have this change automatically run at boot time, add the following line to /etc/sysctl.conf. kern.timecounter.hardware=i8254 Why did my laptop fail to correctly probe PC cards? This problem is common on laptops that boot more than one operating system. Some non-BSD operating systems leave PC card hardware in an inconsistent state. pccardd will detect the card as "(null)""(null)" instead of its actual model. You must remove all power from the PC card slot to fully reset the hardware. Completely power off the laptop. (Don't suspend it, don't let it go into standby; the power needs to be completely off.) Wait a few moments, and reboot. Your PC card should work now. Some laptop hardware lies when it claims to be off. If the above does not work shut down, remove the battery, wait a moment, replace the battery, and reboot. Why does FreeBSD's boot loader display Read error and stop after the BIOS screen? FreeBSD's boot loader is incorrectly recognizing the hard drive's geometry. This must be manually set within fdisk when creating or modifying FreeBSD's slice. The correct drive geometry values can be found within the machine's BIOS. Look for the number of cylinders, heads and sectors for the particular drive. Within &man.sysinstall.8;'s fdisk, hit G to set the drive geometry. A dialog will pop up requesting the number of cylinders, heads and sectors. Type the numbers found from the BIOS separates by forward slashes. 5000 cylinders, 250 sectors and 60 sectors would be entered as 5000/250/60 Press enter to set the values, and hit W to write the new partition table to the drive. Another operating system destroyed my Boot Manager. How do I get it back? Enter &man.sysinstall.8; and choose Configure, then Fdisk. Select the disk the Boot Manager resided on with the space key. Press W to write changes to the drive. A prompt will appear asking which boot loader to install. Select this, and it will be restored. What does the error swap_pager: indefinite wait buffer: mean? This means that a process is trying to page memory to disk, and the page attempt has hung trying to access the disk for more than 20 seconds. It might be caused by bad blocks on the disk drive, disk wiring, cables, or any other disk I/O-related hardware. If the drive itself is actually bad, you will also see disk errors in /var/log/messages and in the output of dmesg. Otherwise, check your cables and connections. Commercial Applications This section is still very sparse, though we are hoping, of course, that companies will add to it! :) The FreeBSD group has no financial interest in any of the companies listed here but simply lists them as a public service (and feels that commercial interest in FreeBSD can have very positive effects on FreeBSD's long-term viability). We encourage commercial software vendors to send their entries here for inclusion. See the Vendors page for a longer list. Where can I get an Office Suite for FreeBSD? The FreeBSD Mall offers a FreeBSD native version of VistaSource ApplixWare 5. ApplixWare is a rich full-featured, commercial Office Suite for FreeBSD containing a word processor, spreadsheet, presentation program, vector drawing package, and other applications. ApplixWare is offered as part of the FreeBSD Mall's BSD Desktop Edition. The Linux version of StarOffice works flawlessly on FreeBSD. The easiest way to install the Linux version of StarOffice is through the FreeBSD Ports collection. Future versions of the open-source OpenOffice suite should work as well. Where can I get Motif for FreeBSD? The Open Group has released the source code to Motif 2.1.30. You can install the open-motif package, or compile it from ports. Refer to the ports section of the Handbook for more information on how to do this. The Open Motif distribution only allows redistribution if it is running on an open source operating system. In addition, there are commercial distributions of the Motif software available. These, however, are not for free, but their license allows them to be used in closed-source software. Contact Apps2go for the least expensive ELF Motif 2.1.20 distribution for FreeBSD (either i386 or Alpha). There are two distributions, the development edition and the runtime edition (for much less). These distributions includes: OSF/Motif manager, xmbind, panner, wsm. Development kit with uil, mrm, xm, xmcxx, include and Imake files. Static and dynamic ELF libraries (for use with FreeBSD 3.0 and above). Demonstration applets. Be sure to specify that you want the FreeBSD version of Motif when ordering (do not forget to mention the architecture you want too)! Versions for NetBSD and OpenBSD are also sold by Apps2go. This is currently a FTP only download. More info Apps2go WWW page or sales@apps2go.com or support@apps2go.com or phone (817) 431 8775 or +1 817 431-8775 Contact Metro Link for an either ELF or a.out Motif 2.1 distribution for FreeBSD. This distribution includes: OSF/Motif manager, xmbind, panner, wsm. Development kit with uil, mrm, xm, xmcxx, include and Imake files. Static and dynamic libraries (specify ELF for use with FreeBSD 3.0 and later; or a.out for use with FreeBSD 2.2.8 and earlier). Demonstration applets. Preformatted man pages. Be sure to specify that you want the FreeBSD version of Motif when ordering! Versions for Linux are also sold by Metro Link. This is available on either a CDROM or for FTP download. Contact Xi Graphics for an a.out Motif 2.0 distribution for FreeBSD. This distribution includes: OSF/Motif manager, xmbind, panner, wsm. Development kit with uil, mrm, xm, xmcxx, include and Imake files. Static and dynamic libraries (for use with FreeBSD 2.2.8 and earlier). Demonstration applets. Preformatted man pages. Be sure to specify that you want the FreeBSD version of Motif when ordering! Versions for BSDI and Linux are also sold by Xi Graphics. This is currently a 4 diskette set... in the future this will change to a unified CD distribution like their CDE. Where can I get CDE for FreeBSD? Xi Graphics used to sell CDE for FreeBSD, but no longer do. KDE is an open source X11 desktop which is similar to CDE in many respects. You might also like the look and feel of xfce. KDE and xfce are both in the ports system. Are there any commercial high-performance X servers? Yes, Xi Graphics and Metro Link sell Accelerated-X product for FreeBSD and other Intel based systems. The Metro Link offering is a high performance X Server that offers easy configuration using the FreeBSD Package suite of tools, support for multiple concurrent video boards and is distributed in binary form only, in a convenient FTP download. Not to mention the Metro Link offering is available at the very reasonable price of $39. Metro Link also sells both ELF and a.out Motif for FreeBSD (see above). More info Metro Link WWW page or sales@metrolink.com or tech@metrolink.com or phone (954) 938-0283 or +1 954 938-0283 The Xi Graphics offering is a high performance X Server that offers easy configuration, support for multiple concurrent video boards and is distributed in binary form only, in a unified diskette distribution for FreeBSD and Linux. Xi Graphics also offers a high performance X Server tailored for laptop support. There is a free compatibility demo of version 5.0 available. Xi Graphics also sells Motif and CDE for FreeBSD (see above). More info Xi Graphics WWW page or sales@xig.com or support@xig.com or phone (800) 946 7433 or +1 303 298-7478. Are there any Database systems for FreeBSD? Yes! See the Commercial Vendors section of FreeBSD's Web site. Also see the Databases section of the Ports collection. Can I run Oracle on FreeBSD? Yes. The following pages tell you exactly how to setup Linux-Oracle on FreeBSD: http://www.scc.nl/~marcel/howto-oracle.html http://www.lf.net/lf/pi/oracle/install-linux-oracle-on-freebsd User Applications So, where are all the user applications? Please take a look at the ports page for info on software packages ported to FreeBSD. The list currently tops &os.numports; and is growing daily, so come back to check often or subscribe to the freebsd-announce mailing list for periodic updates on new entries. Most ports should be available for the 2.2, 3.x and 4.x branches, and many of them should work on 2.1.x systems as well. Each time a FreeBSD release is made, a snapshot of the ports tree at the time of release in also included in the ports/ directory. We also support the concept of a package, essentially no more than a gzipped binary distribution with a little extra intelligence embedded in it for doing whatever custom installation work is required. A package can be installed and uninstalled again easily without having to know the gory details of which files it includes. Use the package installation menu in /stand/sysinstall (under the post-configuration menu item) or invoke the &man.pkg.add.1; command on the specific package files you are interested in installing. Package files can usually be identified by their .tgz suffix and CDROM distribution people will have a packages/All directory on their CD which contains such files. They can also be downloaded over the net for various versions of FreeBSD at the following locations: for 2.2.8-RELEASE/2.2.8-STABLE ftp://ftp.FreeBSD.org/pub/FreeBSD/ports/i386/packages-2.2.8/ for 3.X-RELEASE/3.X-STABLE ftp://ftp.FreeBSD.org/pub/FreeBSD/ports/i386/packages-3-stable/ for 4.X-RELEASE/4-STABLE ftp://ftp.FreeBSD.org/pub/FreeBSD/ports/i386/packages-4-stable/ for 5.X-CURRENT ftp://ftp.FreeBSD.org/pub/FreeBSD/ports/i386/packages-5-current or your nearest local mirror site. Note that all ports may not be available as packages since new ones are constantly being added. It is always a good idea to check back periodically to see which packages are available at the ftp.FreeBSD.org master site. Where do I find libc.so.3.0? You are trying to run a package built on 2.2 and later on a 2.1.x system. Please take a look at the previous section and get the correct port/package for your system. Why do I get a message reading Error: can't find libc.so.4.0? You accidently downloaded packages meant for 4.X and 5.X systems and attempted to install them on your 2.X or 3.X FreeBSD system. Please download the correct version of the packages. Why does ghostscript give lots of errors with my 386/486SX? You do not have a math co-processor, right? You will need to add the alternative math emulator to your kernel; you do this by adding the following to your kernel config file and it will be compiled in. options GPL_MATH_EMULATE You will need to remove the MATH_EMULATE option when you do this. Why do SCO/iBCS2 applications bomb on socksys? (FreeBSD 3.0 and older only). You first need to edit the /etc/sysconfig (or /etc/rc.conf, see &man.rc.conf.5;) file in the last section to change the following variable to YES: # Set to YES if you want ibcs2 (SCO) emulation loaded at startup ibcs2=NO It will load the ibcs2 kernel module at startup. You will then need to set up /compat/ibcs2/dev to look like: lrwxr-xr-x 1 root wheel 9 Oct 15 22:20 X0R@ -> /dev/null lrwxr-xr-x 1 root wheel 7 Oct 15 22:20 nfsd@ -> socksys -rw-rw-r-- 1 root wheel 0 Oct 28 12:02 null lrwxr-xr-x 1 root wheel 9 Oct 15 22:20 socksys@ -> /dev/null crw-rw-rw- 1 root wheel 41, 1 Oct 15 22:14 spx You just need socksys to go to /dev/null (see &man.null.4;) to fake the open & close. The code in -CURRENT will handle the rest. This is much cleaner than the way it was done before. If you want the spx driver for a local socket X connection, define SPX_HACK when you compile the system. How do I configure INN (Internet News) for my machine? After installing the news/inn package or port, an excellent place to start is Dave Barr's INN Page where you will find the INN FAQ. What version of Microsoft FrontPage should I get? Use the Port, Luke! A pre-patched version of Apache, apache13-fp, is available in the ports tree. Does FreeBSD support Java? Yes. Please see http://www.FreeBSD.org/java/. Why can I not build this port on my 3.X-STABLE machine? If you are running a FreeBSD version that lags significantly behind -CURRENT or -STABLE, you may need a ports upgrade kit from http://www.FreeBSD.org/ports/. If you are up to date, then someone might have committed a change to the port which works for -CURRENT but which broke the port for -STABLE. Please submit a bug report on this with the &man.send-pr.1; command, since the ports collection is supposed to work for both the -CURRENT and -STABLE branches. Where do I find ld.so? a.out applications like Netscape Navigator require a.out libraries. A version of FreeBSD built with ELF libraries does not install them by default. You will get complaints about not having /usr/libexec/ld.so if this is the case on your system. These libraries are available as an add-on in the compat22 distribution. Use &man.sysinstall.8; to install them. You can also install them from the FreeBSD source code: &prompt.root; cd /usr/src/lib/compat/compat22 &prompt.root; make install clean If you want to install the latest compat22 libraries whenever you run make world, edit /etc/make.conf to include COMPAT22=YES. Old compatibility libraries change rarely, if ever, so this is not generally needed. Also see the ERRATAs for 3.1-RELEASE and 3.2-RELEASE. I updated the sources, now how do I update my installed ports? FreeBSD does not include a port upgrading tool, but it does have some tools to make the upgrade process somewhat easier. You can also install additional tools to simplify port handling. The &man.pkg.version.1; command can generate a script that will update installed ports to the latest version in the ports tree. &prompt.root; pkg_version > /tmp/myscript The output script must be edited by hand before you use it. Current versions of &man.pkg.version.1; force this by inserting an &man.exit.1; at the beginning of the script. You should save the output of the script, as it will note packages that depend on the one that has been updated. These may or may not need to be updated as well. The usual case where they need to be updated is that a shared library has changed version numbers, so the ports that used that library need to be rebuilt to use the new version. If you have the disk space, you can use the portupgrade tool to automate all of this. portupgrade includes various tools to simplify package handling. It is available under sysutils/portupgrade. Since it is written in Ruby, portupgrade is an unlikely candidate for integration with the main FreeBSD tree. That should not stop anyone from using it, however. If your system is up full time, the &man.periodic.8; system can be used to generate a weekly list of ports that might need updating by setting weekly_status_pkg_enable="YES" in /etc/periodic.conf. Why is /bin/sh so minimal? Why does FreeBSD not use bash or another shell? Because POSIX says that there shall be such a shell. The more complicated answer: many people need to write shell scripts which will be portable across many systems. That is why POSIX specifies the shell and utility commands in great detail. Most scripts are written in Bourne shell, and because several important programming interfaces (&man.make.1;, &man.system.3;, &man.popen.3;, and analogues in higher-level scripting languages like Perl and Tcl) are specified to use the Bourne shell to interpret commands. Because the Bourne shell is so often and widely used, it is important for it to be quick to start, be deterministic in its behavior, and have a small memory footprint. The existing implementation is our best effort at meeting as many of these requirements simultaneously as we can. In order to keep /bin/sh small, we have not provided many of the convenience features that other shells have. That is why the Ports Collection includes more featureful shells like bash, scsh, tcsh, and zsh. (You can compare for yourself the memory utilization of all these shells by looking at the VSZ and RSS columns in a ps -u listing.) Why do Netscape and Opera take so long to start? The usual answer is that DNS on your system is misconfigured. Both Netscape and Opera perform DNS checks when starting up. The browser will not appear on your desktop until the program either gets a response or determines that the system has no network connection. Kernel Configuration I would like to customize my kernel. Is it difficult? Not at all! Check out the kernel config section of the Handbook. We recommend that you make a dated snapshot of your new /kernel called /kernel.YYMMDD after you get it working properly. Also back up your new /modules directory to /modules.YYMMDD. That way, if you make a mistake the next time you play with your configuration you can boot the backup kernel instead of having to fall back to kernel.GENERIC. This is particularly important if you are now booting from a controller that GENERIC does not support. My kernel compiles fail because _hw_float is missing. How do I solve this problem? Let me guess. You removed npx0 (see &man.npx.4;) from your kernel configuration file because you do not have a math co-processor, right? Wrong! :-) The npx0 is MANDATORY. Even if you do not have a mathematic co-processor, you must include the npx0 device. Why is my kernel so big (over 10MB)? Chances are, you compiled your kernel in debug mode. Kernels built in debug mode contain many symbols that are used for debugging, thus greatly increasing the size of the kernel. Note that if you running a FreeBSD 3.0 or later system, there will be little or no performance decrease from running a debug kernel, and it is useful to keep one around in case of a system panic. However, if you are running low on disk space, or you simply do not want to run a debug kernel, make sure that both of the following are true: You do not have a line in your kernel configuration file that reads: makeoptions DEBUG=-g You are not running &man.config.8; with the option. Both of the above situations will cause your kernel to be built in debug mode. As long as you make sure you follow the steps above, you can build your kernel normally, and you should notice a fairly large size decrease; most kernels tend to be around 1.5MB to 2MB. Why do I get interrupt conflicts with multi-port serial code? When I compile a kernel with multi-port serial code, it tells me that only the first port is probed and the rest skipped due to interrupt conflicts. How do I fix this? The problem here is that FreeBSD has code built-in to keep the kernel from getting trashed due to hardware or software conflicts. The way to fix this is to leave out the IRQ settings on all but one port. Here is an example: # # Multiport high-speed serial line - 16550 UARTS # device sio2 at isa? port 0x2a0 tty irq 5 flags 0x501 vector siointr device sio3 at isa? port 0x2a8 tty flags 0x501 vector siointr device sio4 at isa? port 0x2b0 tty flags 0x501 vector siointr device sio5 at isa? port 0x2b8 tty flags 0x501 vector siointr Why does every kernel I try to build fail to compile, even GENERIC? There are a number of possible causes for this problem. They are, in no particular order: You are not using the new make buildkernel and make installkernel targets, and your source tree is different from the one used to build the currently running system (e.g., you are compiling 4.3-RELEASE on a 4.0-RELEASE system). If you are attempting an upgrade, please read the /usr/src/UPDATING file, paying particular attention to the COMMON ITEMS section at the end. You are using the new make buildkernel and make installkernel targets, but you failed to assert the completion of the make buildworld target. The make buildkernel target relies on files generated by the make buildworld target to complete its job correctly. Even if you are trying to build FreeBSD-STABLE, it is possible that you fetched the source tree at a time when it was either being modified, or broken for other reasons; only releases are absolutely guaranteed to be buildable, although FreeBSD-STABLE builds fine the majority of the time. If you have not already done so, try re-fetching the source tree and see if the problem goes away. Try using a different server in case the one you are using is having problems. Disks, Filesystems, and Boot Loaders How can I add my new hard disk to my FreeBSD system? See the Disk Formatting Tutorial at www.FreeBSD.org. How do I move my system over to my huge new disk? The best way is to reinstall the OS on the new disk, then move the user data over. This is highly recommended if you have been tracking -stable for more than one release, or have updated a release instead of installing a new one. You can install booteasy on both disks with &man.boot0cfg.8;, and dual boot them until you are happy with the new configuration. Skip the next paragraph to find out how to move the data after doing this. Should you decide not to do a fresh install, you need to partition and label the new disk with either /stand/sysinstall, or &man.fdisk.8; and &man.disklabel.8;. You should also install booteasy on both disks with &man.boot0cfg.8;, so that you can dual boot to the old or new system after the copying is done. See the formatting-media article for details on this process. Now you have the new disk set up, and are ready to move the data. Unfortunately, you cannot just blindly copy the data. Things like device files (in /dev), flags, and links tend to screw that up. You need to use tools that understand these things, which means &man.dump.8;. Although it is suggested that you move the data in single user mode, it is not required. You should never use anything but &man.dump.8; and &man.restore.8; to move the root filesystem. The &man.tar.1; command may work - then again, it may not. You should also use &man.dump.8; and &man.restore.8; if you are moving a single partition to another empty partition. The sequence of steps to use dump to move a partitions data to a new partition is: newfs the new partition. mount it on a temporary mount point. cd to that directory. dump the old partition, piping output to the new one. For example, if you are going to move root to /dev/ad1s1a, with /mnt as the temporary mount point, it is: &prompt.root; newfs /dev/ad1s1a &prompt.root; mount /dev/ad1s1a /mnt &prompt.root; cd /mnt &prompt.root; dump 0af - / | restore xf - Rearranging your partitions with dump takes a bit more work. To merge a partition like /var into its parent, create the new partition large enough for both, move the parent partition as described above, then move the child partition into the empty directory that the first move created: &prompt.root; newfs /dev/ad1s1a &prompt.root; mount /dev/ad1s1a /mnt &prompt.root; cd /mnt &prompt.root; dump 0af - / | restore xf - &prompt.root; cd var &prompt.root; dump 0af - /var | restore xf - To split a directory from its parent, say putting /var on its own partition when it was not before, create both partitions, then mount the child partition on the appropriate directory in the temporary mount point, then move the old single partition: &prompt.root; newfs /dev/ad1s1a &prompt.root; newfs /dev/ad1s1d &prompt.root; mount /dev/ad1s1a /mnt &prompt.root; mkdir /mnt/var &prompt.root; mount /dev/ad1s1d /mnt/var &prompt.root; cd /mnt &prompt.root; dump 0af - / | restore xf - You might prefer &man.cpio.1;, &man.pax.1;, &man.tar.1; to &man.dump.8; for user data. At the time of this writing, these are known to lose file flag information, so use them with caution. Will a dangerously dedicated disk endanger my health? The installation procedure allows you to chose two different methods in partitioning your hard disk(s). The default way makes it compatible with other operating systems on the same machine, by using fdisk table entries (called slices in FreeBSD), with a FreeBSD slice that employs partitions of its own. Optionally, one can chose to install a boot-selector to switch between the possible operating systems on the disk(s). The alternative uses the entire disk for FreeBSD, and makes no attempt to be compatible with other operating systems. So why it is called dangerous? A disk in this mode does not contain what normal PC utilities would consider a valid fdisk table. Depending on how well they have been designed, they might complain at you once they are getting in contact with such a disk, or even worse, they might damage the BSD bootstrap without even asking or notifying you. In addition, the dangerously dedicated disk's layout is known to confuse many BIOSes, including those from AWARD (e.g. as found in HP Netserver and Micronics systems as well as many others) and Symbios/NCR (for the popular 53C8xx range of SCSI controllers). This is not a complete list, there are more. Symptoms of this confusion include the read error message printed by the FreeBSD bootstrap when it cannot find itself, as well as system lockups when booting. Why have this mode at all then? It only saves a few kbytes of disk space, and it can cause real problems for a new installation. Dangerously dedicated mode's origins lie in a desire to avoid one of the most common problems plaguing new FreeBSD installers - matching the BIOS geometry numbers for a disk to the disk itself. Geometry is an outdated concept, but one still at the heart of the PC's BIOS and its interaction with disks. When the FreeBSD installer creates slices, it has to record the location of these slices on the disk in a fashion that corresponds with the way the BIOS expects to find them. If it gets it wrong, you will not be able to boot. Dangerously dedicated mode tries to work around this by making the problem simpler. In some cases, it gets it right. But it is meant to be used as a last-ditch alternative - there are better ways to solve the problem 99 times out of 100. So, how do you avoid the need for DD mode when you are installing? Start by making a note of the geometry that your BIOS claims to be using for your disks. You can arrange to have the kernel print this as it boots by specifying at the boot: prompt, or using boot -v in the loader. Just before the installer starts, the kernel will print a list of BIOS geometries. Do not panic - wait for the installer to start and then use scrollback to read the numbers. Typically the BIOS disk units will be in the same order that FreeBSD lists your disks, first IDE, then SCSI. When you are slicing up your disk, check that the disk geometry displayed in the FDISK screen is correct (ie. it matches the BIOS numbers); if it is wrong, use the g key to fix it. You may have to do this if there is absolutely nothing on the disk, or if the disk has been moved from another system. Note that this is only an issue with the disk that you are going to boot from; FreeBSD will sort itself out just fine with any other disks you may have. Once you have got the BIOS and FreeBSD agreeing about the geometry of the disk, your problems are almost guaranteed to be over, and with no need for DD mode at all. If, however, you are still greeted with the dreaded read error message when you try to boot, it is time to cross your fingers and go for it - there is nothing left to lose. To return a dangerously dedicated disk for normal PC use, there are basically two options. The first is, you write enough NULL bytes over the MBR to make any subsequent installation believe this to be a blank disk. You can do this for example with &prompt.root; dd if=/dev/zero of=/dev/rda0 count=15 Alternatively, the undocumented DOS feature C:\> fdisk /mbr will to install a new master boot record as well, thus clobbering the BSD bootstrap. Which partitions can safely use softupdates? I have heard that softupdates on / can cause problems. Short answer: you can usually use softupdates safely on all partitions. Long answer: There used to be some concern over using softupdates on the root partition. Softupdates has two characteristics that caused this. First, a softupdates partition has a small chance of losing data during a system crash. (The partition will not be corrupted; the data will simply be lost.) Also, softupdates can cause temporary space shortages. When using softupdates, the kernel can take up to thirty seconds to actually write changes to the physical disk. If you delete a large file, the file still resides on disk until the kernel actually performs the deletion. This can cause a very simple race condition. Suppose you delete one large file and immediately create another large file. The first large file is not yet actually removed from the physical disk, so the disk might not have enough room for the second large file. You get an error that the partition does not have enough space, although you know perfectly well that you just released a large chunk of space! When you try again mere seconds later, the file creation works as you expect. This has left more than one user scratching his head and doubting his sanity, the FreeBSD filesystem, or both. If a system should crash after the kernel accepts a chunk of data for writing to disk, but before that data is actually written out, data could be lost or corrupted. This risk is extremely small, but generally manageable. Use of IDE write caching greatly increases this risk; it is strongly recommended that you disable IDE write caching when using softupdates. These issues affect all partitions using softupdates. So, what does this mean for the root partition? Vital information on the root partition changes very rarely. Files such as /kernel and the contents of /etc only change during system maintenance, or when users change their passwords. If the system crashed during the thirty-second window after such a change is made, it is possible that data could be lost. This risk is negligible for most applications, but you should be aware that it exists. If your system cannot tolerate this much risk, do not use softupdates on the root filesystem! / is traditionally one of the smallest partitions. By default, FreeBSD puts the /tmp directory on /. If you have a busy /tmp, you might see intermittent space problems. Symlinking /tmp to /var/tmp will solve this problem. What is inappropriate about my ccd? The symptom of this is: &prompt.root; ccdconfig -C ccdconfig: ioctl (CCDIOCSET): /dev/ccd0c: Inappropriate file type or format This usually happens when you are trying to concatenate the c partitions, which default to type unused. The ccd driver requires the underlying partition type to be FS_BSDFFS. Edit the disklabel of the disks you are trying to concatenate and change the types of partitions to 4.2BSD. Why can I not edit the disklabel on my ccd? The symptom of this is: &prompt.root; disklabel ccd0 (it prints something sensible here, so let us try to edit it) &prompt.root; disklabel -e ccd0 (edit, save, quit) disklabel: ioctl DIOCWDINFO: No disk label on disk; use "disklabel -r" to install initial label This is because the disklabel returned by ccd is actually a fake one that is not really on the disk. You can solve this problem by writing it back explicitly, as in: &prompt.root; disklabel ccd0 > /tmp/disklabel.tmp &prompt.root; disklabel -Rr ccd0 /tmp/disklabel.tmp &prompt.root; disklabel -e ccd0 (this will work now) Can I mount other foreign filesystems under FreeBSD? Digital UNIX UFS CDROMs can be mounted directly on FreeBSD. Mounting disk partitions from Digital UNIX and other systems that support UFS may be more complex, depending on the details of the disk partitioning for the operating system in question. Linux As of 2.2, FreeBSD supports ext2fs partitions. See &man.mount.ext2fs.8; for more information. NT A read-only NTFS driver exists for FreeBSD. For more information, see this tutorial by Mark Ovens at http://ukug.uk.FreeBSD.org/~mark/ntfs_install.html. Any other information on this subject would be appreciated. How do I mount a secondary DOS partition? The secondary DOS partitions are found after ALL the primary partitions. For example, if you have an E partition as the second DOS partition on the second SCSI drive, you need to create the special files for slice 5 in /dev, then mount /dev/da1s5: &prompt.root; cd /dev &prompt.root; sh MAKEDEV da1s5 &prompt.root; mount -t msdos /dev/da1s5 /dos/e Is there a cryptographic filesystem for &os;? Yes; see the security/cfs port. How can I use the NT loader to boot FreeBSD? This procedure is slightly different for 2.2.x and 3.x (with the 3-stage boot) systems. The general idea is that you copy the first sector of your native root FreeBSD partition into a file in the DOS/NT partition. Assuming you name that file something like c:\bootsect.bsd (inspired by c:\bootsect.dos), you can then edit the c:\boot.ini file to come up with something like this: [boot loader] timeout=30 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Windows NT" C:\BOOTSECT.BSD="FreeBSD" C:\="DOS" For 2.2.x systems this procedure assumes that DOS, NT, FreeBSD, or whatever have been installed into their respective fdisk partitions on the same disk. This example was tested on a system where DOS & NT were on the first fdisk partition, and FreeBSD on the second. FreeBSD was also set up to boot from its native partition, not the disk's MBR. Mount a DOS-formatted floppy (if you have converted to NTFS) or the FAT partition, under, say, /mnt. &prompt.root; dd if=/dev/rda0a of=/mnt/bootsect.bsd bs=512 count=1 Reboot into DOS or NT. NTFS users copy the bootsect.bsd and/or the bootsect.lnx file from the floppy to C:\. Modify the attributes (permissions) on boot.ini with: C:\> attrib -s -r c:\boot.ini Edit to add the appropriate entries from the example boot.ini above, and restore the attributes: C:\> attrib +s +r c:\boot.ini If FreeBSD is booting from the MBR, restore it with the DOS fdisk command after you reconfigure them to boot from their native partitions. For FreeBSD 3.x systems the procedure is somewhat simpler. If FreeBSD is installed on the same disk as the NT boot partition simply copy /boot/boot1 to C:\BOOTSECT.BSD However, if FreeBSD is installed on a different disk /boot/boot1 will not work, /boot/boot0 is needed. DO NOT SIMPLY COPY /boot/boot0 INSTEAD OF /boot/boot1, YOU WILL OVERWRITE YOUR PARTITION TABLE AND RENDER YOUR COMPUTER UN-BOOTABLE! /boot/boot0 needs to be installed using sysinstall by selecting the FreeBSD boot manager on the screen which asks if you wish to use a boot manager. This is because /boot/boot0 has the partition table area filled with NULL characters but sysinstall copies the partition table before copying /boot/boot0 to the MBR. When the FreeBSD boot manager runs it records the last OS booted by setting the active flag on the partition table entry for that OS and then writes the whole 512-bytes of itself back to the MBR so if you just copy /boot/boot0 to C:\BOOTSECT.BSD then it writes an empty partition table, with the active flag set on one entry, to the MBR. How do I boot FreeBSD and Linux from LILO? If you have FreeBSD and Linux on the same disk, just follow LILO's installation instructions for booting a non-Linux operating system. Very briefly, these are: Boot Linux, and add the following lines to /etc/lilo.conf: other=/dev/hda2 table=/dev/hda label=FreeBSD (the above assumes that your FreeBSD slice is known to Linux as /dev/hda2; tailor to suit your setup). Then, run lilo as root and you should be done. If FreeBSD resides on another disk, you need to add loader=/boot/chain.b to the LILO entry. For example: other=/dev/dab4 table=/dev/dab loader=/boot/chain.b label=FreeBSD In some cases you may need to specify the BIOS drive number to the FreeBSD boot loader to successfully boot off the second disk. For example, if your FreeBSD SCSI disk is probed by BIOS as BIOS disk 1, at the FreeBSD boot loader prompt you need to specify: Boot: 1:da(0,a)/kernel On FreeBSD 2.2.5 and later, you can configure &man.boot.8; to automatically do this for you at boot time. The Linux+FreeBSD mini-HOWTO is a good reference for FreeBSD and Linux interoperability issues. How do I boot FreeBSD and Linux using BootEasy? Install LILO at the start of your Linux boot partition instead of in the Master Boot Record. You can then boot LILO from BootEasy. If you are running Windows-95 and Linux this is recommended anyway, to make it simpler to get Linux booting again if you should need to reinstall Windows95 (which is a Jealous Operating System, and will bear no other Operating Systems in the Master Boot Record). How do I change the boot prompt from ??? to something more meaningful? You can not do that with the standard boot manager without rewriting it. There are a number of other boot managers in the sysutils ports category that provide this functionality. I have a new removable drive, how do I use it? Whether it is a removable drive like a ZIP or an EZ drive (or even a floppy, if you want to use it that way), or a new hard disk, once it is installed and recognized by the system, and you have your cartridge/floppy/whatever slotted in, things are pretty much the same for all devices. (this section is based on Mark Mayo's ZIP FAQ) If it is a ZIP drive or a floppy, you have already got a DOS filesystem on it, you can use a command like this: &prompt.root; mount -t msdos /dev/fd0c /floppy if it is a floppy, or this: &prompt.root; mount -t msdos /dev/da2s4 /zip for a ZIP disk with the factory configuration. For other disks, see how they are laid out using &man.fdisk.8; or &man.sysinstall.8;. The rest of the examples will be for a ZIP drive on da2, the third SCSI disk. Unless it is a floppy, or a removable you plan on sharing with other people, it is probably a better idea to stick a BSD filesystem on it. You will get long filename support, at least a 2X improvement in performance, and a lot more stability. First, you need to redo the DOS-level partitions/filesystems. You can either use &man.fdisk.8; or /stand/sysinstall, or for a small drive that you do not want to bother with multiple operating system support on, just blow away the whole FAT partition table (slices) and just use the BSD partitioning: &prompt.root; dd if=/dev/zero of=/dev/rda2 count=2 &prompt.root; disklabel -Brw da2 auto You can use disklabel or /stand/sysinstall to create multiple BSD partitions. You will certainly want to do this if you are adding swap space on a fixed disk, but it is probably irrelevant on a removable drive like a ZIP. Finally, create a new filesystem, this one is on our ZIP drive using the whole disk: &prompt.root; newfs /dev/rda2c and mount it: &prompt.root; mount /dev/da2c /zip and it is probably a good idea to add a line like this to /etc/fstab (see &man.fstab.5;) so you can just type mount /zip in the future: /dev/da2c /zip ffs rw,noauto 0 0 Why do I get Incorrect super block when mounting a CDROM? You have to tell &man.mount.8; the type of the device that you want to mount. This is described in the Handbook section on optical media, specifically the section Using Data CDs. Why do I get Device not configured when mounting a CDROM? This generally means that there is no CDROM in the CDROM drive, or the drive is not visible on the bus. Please see the Using Data CDs section of the Handbook for a detailed discussion of this issue. Why do all non-English characters in filenames show up as ? on my CDs when mounted in FreeBSD? Your CDROM probably uses the Joliet extension for storing information about files and directories. This is discussed in the Handbook chapter on creating and using CDROMs, specifically the section on Using Data CDROMs. I burned a CD under FreeBSD and now I can not read it under any other operating system. Why? You most likely burned a raw file to your CD, rather than creating an ISO 9660 filesystem. Take a look at the Handbook chapter on creating CDROMs, particularly the section on burning raw data CDs. How can I create an image of a data CD? This is discussed in the Handbook section on duplicating data CDs. For more on working with CDROMs, see the Creating CDs Section in the Storage chapter in the Handbook. Why can I not mount an audio CD? If you try to mount an audio CD, you will get an error like cd9660: /dev/acd0c: Invalid argument. This is because mount only works on filesystems. Audio CDs do not have filesystems; they just have data. You need a program that reads audio CDs, such as the audio/xmcd port. How do I mount a multi-session CD? By default, &man.mount.8; will attempt to mount the last data track (session) of a CD. If you would like to load an earlier session, you must use the command line argument. Please see &man.mount.cd9660.8; for specific examples. How do I let ordinary users mount floppies, CDROMs and other removable media? Ordinary users can be permitted to mount devices. Here is how: As root set the sysctl variable vfs.usermount to 1. &prompt.root; sysctl -w vfs.usermount=1 As root assign the appropriate permissions to the block device associated with the removable media. For example, to allow users to mount the first floppy drive, use: &prompt.root; chmod 666 /dev/fd0 To allow users in the group operator to mount the CDROM drive, use: &prompt.root; chgrp operator /dev/cd0c &prompt.root; chmod 640 /dev/cd0c Finally, add the line vfs.usermount=1 to the file /etc/sysctl.conf so that it is reset at system boot time. All users can now mount the floppy /dev/fd0 onto a directory that they own: &prompt.user; mkdir ~/my-mount-point &prompt.user; mount -t msdos /dev/fd0 ~/my-mount-point Users in group operator can now mount the CDROM /dev/cd0c onto a directory that they own: &prompt.user; mkdir ~/my-mount-point &prompt.user; mount -t msdos /dev/cd0c ~/my-mount-point Unmounting the device is simple: &prompt.user; umount ~/my-mount-point Enabling vfs.usermount, however, has negative security implications. A better way to access MSDOS formatted media is to use the mtools package in the ports collection. The du and df commands show different amounts of disk space available. What is going on? You need to understand what du and df really do. du goes through the directory tree, measures how large each file is, and presents the totals. df just asks the filesystem how much space it has left. They seem to be the same thing, but a file without a directory entry will affect df but not du. When a program is using a file, and you delete the file, the file is not really removed from the filesystem until the program stops using it. The file is immediately deleted from the directory listing, however. You can see this easily enough with a program such as more. Assume you have a file large enough that its presence affects the output of du and df. (Since disks can be so large today, this might be a very large file!) If you delete this file while using more on it, more does not immediately choke and complain that it cannot view the file. The entry is simply removed from the directory so no other program or user can access it. du shows that it is gone — it has walked the directory tree and the file is not listed. df shows that it is still there, as the filesystem knows that more is still using that space. Once you end the more session, du and df will agree. Note that softupdates can delay the freeing of disk space; you might need to wait up to 30 seconds for the change to be visible! This situation is common on web servers. Many people set up a FreeBSD web server and forget to rotate the log files. The access log fills up /var. The new administrator deletes the file, but the system still complains that the partition is full. Stopping and restarting the web server program would free the file, allowing the system to release the disk space. To prevent this from happening, set up &man.newsyslog.8;. How can I add more swap space? In the Configuration and Tuning section of the Handbook, you will find a section describing how to do this. System Administration Where are the system start-up configuration files? From 2.0.5R to 2.2.1R, the primary configuration file is /etc/sysconfig. All the options are to be specified in this file and other files such as /etc/rc (see &man.rc.8;) and /etc/netstart just include it. Look in the /etc/sysconfig file and change the value to match your system. This file is filled with comments to show what to put in there. In post-2.2.1 and 3.0, /etc/sysconfig was renamed to a more self-describing &man.rc.conf.5; file and the syntax cleaned up a bit in the process. /etc/netstart was also renamed to /etc/rc.network so that all files could be copied with a cp /usr/src/etc/rc* /etc command. And, in 3.1 and later, /etc/rc.conf has been moved to /etc/defaults/rc.conf. Do not edit this file! Instead, if there is any entry in /etc/defaults/rc.conf that you want to change, you should copy the line into /etc/rc.conf and change it there. For example, if you wish to start named, the DNS server included with FreeBSD in FreeBSD 3.1 or later, all you need to do is: &prompt.root; echo named_enable="YES" >> /etc/rc.conf To start up local services in FreeBSD 3.1 or later, place shell scripts in the /usr/local/etc/rc.d directory. These shell scripts should be set executable, and end with a .sh. In FreeBSD 3.0 and earlier releases, you should edit the /etc/rc.local file. The /etc/rc.serial is for serial port initialization (e.g. locking the port characteristics, and so on.). The /etc/rc.i386 is for Intel-specifics settings, such as iBCS2 emulation or the PC system console configuration. How do I add a user easily? Use the &man.adduser.8; command. For more complicated usage, the &man.pw.8; command. To remove the user again, use the &man.rmuser.8; command. Once again, &man.pw.8; will work as well. Why do I keep getting messages like root: not found after editing my crontab file? This is normally caused by editing the system crontab (/etc/crontab) and then using &man.crontab.1; to install it: &prompt.root; crontab /etc/crontab This is not the correct way to do things. The system crontab has a different format to the per-user crontabs which &man.crontab.1; updates (the &man.crontab.5; manual page explains the differences in more detail). If this is what you did, the extra crontab is simply a copy of /etc/crontab in the wrong format it. Delete it with the command: &prompt.root; crontab -r Next time, when you edit /etc/crontab, you should not do anything to inform &man.cron.8; of the changes, since it will notice them automatically. If you want something to be run once per day, week, or month, it is probably better to add shell scripts /usr/local/etc/periodic, and let the &man.periodic.8; command run from the system cron schedule it with the other periodic system tasks. The actual reason for the error is that the system crontab has an extra field, specifying which user to run the command as. In the default system crontab provided with FreeBSD, this is root for all entries. When this crontab is used as the root user's crontab (which is not the same as the system crontab), &man.cron.8; assumes the string root is the first word of the command to execute, but no such command exists. Why do I get the error, you are not in the correct group to su root when I try to su to root? This is a security feature. In order to su to root (or any other account with superuser privileges), you must be in the wheel group. If this feature were not there, anybody with an account on a system who also found out root's password would be able to gain superuser level access to the system. With this feature, this is not strictly true; &man.su.1; will prevent them from even trying to enter the password if they are not in wheel. To allow someone to su to root, simply put them in the wheel group. I made a mistake in rc.conf, or another startup file, and now I cannot edit it because the filesystem is read-only. What should I do? When you get the prompt to enter the shell pathname, simply press ENTER, and run mount / to re-mount the root filesystem in read/write mode. You may also need to run mount -a -t ufs to mount the filesystem where your favourite editor is defined. If your favourite editor is on a network filesystem, you will need to either configure the network manually before you can mount network filesystems, or use an editor which resides on a local filesystem, such as &man.ed.1;. If you intend to use a full screen editor such as &man.vi.1; or &man.emacs.1;, you may also need to run export TERM=cons25 so that these editors can load the correct data from the &man.termcap.5; database. Once you have performed these steps, you can edit /etc/rc.conf as you usually would to fix the syntax error. The error message displayed immediately after the kernel boot messages should tell you the number of the line in the file which is at fault. Why am I having trouble setting up my printer? Please have a look at the Handbook entry on printing. It should cover most of your problem. See the Handbook entry on printing. Some printers require a host-based driver to do any kind of printing. These so-called WinPrinters are not natively supported by FreeBSD. If your printer does not work in DOS or Windows NT 4.0, it is probably a WinPrinter. Your only hope of getting one of these to work is to check if the print/pnm2ppa port supports it. How can I correct the keyboard mappings for my system? Please see the Handbook section on using localization, specifically the section on console setup. Why do I get messages like: unknown: <PNP0303> can't assign resources on boot? The following is an excerpt from a post to the freebsd-current mailing list.
&a.wollman;, 24 April 2001 The can't assign resources messages indicate that the devices are legacy ISA devices for which a non-PnP-aware driver is compiled into the kernel. These include devices such as keyboard controllers, the programmable interrupt controller chip, and several other bits of standard infrastructure. The resources cannot be assigned because there is already a driver using those addresses.
Why can I not get user quotas to work properly? Do not turn on quotas on /, Put the quota file on the filesystem that the quotas are to be enforced on. ie: Filesystem Quota file /usr /usr/admin/quotas /home /home/admin/quotas … … Does FreeBSD support System V IPC primitives? Yes, FreeBSD supports System V-style IPC. This includes shared memory, messages and semaphores. You need to add the following lines to your kernel config to enable them. options SYSVSHM # enable shared memory options SYSVSEM # enable for semaphores options SYSVMSG # enable for messaging In FreeBSD 3.2 and later, these options are already part of the GENERIC kernel, which means they should already be compiled into your system. Recompile and install your kernel. How do I use sendmail for mail delivery with UUCP? The sendmail configuration that ships with FreeBSD is suited for sites that connect directly to the Internet. Sites that wish to exchange their mail via UUCP must install another sendmail configuration file. Tweaking /etc/mail/sendmail.cf manually is considered something for purists. Sendmail version 8 comes with a new approach of generating config files via some &man.m4.1; preprocessing, where the actual hand-crafted configuration is on a higher abstraction level. You should use the configuration files under /usr/src/usr.sbin/sendmail/cf. If you did not install your system with full sources, the sendmail config stuff has been broken out into a separate source distribution tarball just for you. Assuming you have got your CDROM mounted, do: &prompt.root; cd /cdrom/src &prompt.root; cat scontrib.?? | tar xzf - -C /usr/src contrib/sendmail Do not panic, this is only a few hundred kilobytes in size. The file README in the cf directory can serve as a basic introduction to m4 configuration. For UUCP delivery, you are best advised to use the mailertable feature. This constitutes a database that sendmail can use to base its routing decision upon. First, you have to create your .mc file. The directory /usr/src/usr.sbin/sendmail/cf/cf is the home of these files. Look around, there are already a few examples. Assuming you have named your file foo.mc, all you need to do in order to convert it into a valid sendmail.cf is: &prompt.root; cd /usr/src/usr.sbin/sendmail/cf/cf &prompt.root; make foo.cf &prompt.root; cp foo.cf /etc/mail/sendmail.cf A typical .mc file might look like: VERSIONID(`Your version number') OSTYPE(bsd4.4) FEATURE(accept_unresolvable_domains) FEATURE(nocanonify) FEATURE(mailertable, `hash -o /etc/mail/mailertable') define(`UUCP_RELAY', your.uucp.relay) define(`UUCP_MAX_SIZE', 200000) define(`confDONT_PROBE_INTERFACES') MAILER(local) MAILER(smtp) MAILER(uucp) Cw your.alias.host.name Cw youruucpnodename.UUCP The lines containing accept_unresolvable_domains, nocanonify, and confDONT_PROBE_INTERFACES features will prevent any usage of the DNS during mail delivery. The UUCP_RELAY clause is needed for bizarre reasons, do not ask. Simply put an Internet hostname there that is able to handle .UUCP pseudo-domain addresses; most likely, you will enter the mail relay of your ISP there. Once you have got this, you need this file called /etc/mail/mailertable. If you have only one link to the outside that is used for all your mails, the following file will be enough: # # makemap hash /etc/mail/mailertable.db < /etc/mail/mailertable . uucp-dom:your.uucp.relay A more complex example might look like this: # # makemap hash /etc/mail/mailertable.db < /etc/mail/mailertable # horus.interface-business.de uucp-dom:horus .interface-business.de uucp-dom:if-bus interface-business.de uucp-dom:if-bus .heep.sax.de smtp8:%1 horus.UUCP uucp-dom:horus if-bus.UUCP uucp-dom:if-bus . uucp-dom: As you can see, this is part of a real-life file. The first three lines handle special cases where domain-addressed mail should not be sent out to the default route, but instead to some UUCP neighbor in order to shortcut the delivery path. The next line handles mail to the local Ethernet domain that can be delivered using SMTP. Finally, the UUCP neighbors are mentioned in the .UUCP pseudo-domain notation, to allow for a uucp-neighbor !recipient override of the default rules. The last line is always a single dot, matching everything else, with UUCP delivery to a UUCP neighbor that serves as your universal mail gateway to the world. All of the node names behind the uucp-dom: keyword must be valid UUCP neighbors, as you can verify using the command uuname. As a reminder that this file needs to be converted into a DBM database file before being usable, the command line to accomplish this is best placed as a comment at the top of the mailertable. You always have to execute this command each time you change your mailertable. Final hint: if you are uncertain whether some particular mail routing would work, remember the option to sendmail. It starts sendmail in address test mode; simply enter 3,0, followed by the address you wish to test for the mail routing. The last line tells you the used internal mail agent, the destination host this agent will be called with, and the (possibly translated) address. Leave this mode by typing Control-D. &prompt.user; sendmail -bt ADDRESS TEST MODE (ruleset 3 NOT automatically invoked) Enter <ruleset> <address> > 3,0 foo@example.com canonify input: foo @ example . com ... parse returns: $# uucp-dom $@ your.uucp.relay $: foo < @ example . com . > > ^D How do I set up mail with a dialup connection to the 'net? If you have got a statically assigned IP number, you should not need to adjust anything from the default. Set your host name up as your assigned Internet name and sendmail will do the rest. If you have got a dynamically assigned IP number and use a dialup PPP connection to the Internet, you will probably be given a mailbox on your ISPs mail server. Lets assume your ISPs domain is example.net, and that your user name is user. Lets also assume you have called your machine bsd.home and that your ISP has told you that you may use relay.example.net as a mail relay. In order to retrieve mail from your mailbox, you will need to install a retrieval agent. Fetchmail is a good choice as it supports many different protocols. Usually, POP3 will be provided by your ISP. If you have chosen to use user-PPP, you can automatically fetch your mail when a connection to the 'net is established with the following entry in /etc/ppp/ppp.linkup: MYADDR: !bg su user -c fetchmail If you are using sendmail (as shown below) to deliver mail to non-local accounts, put the command !bg su user -c "sendmail -q" after the above shown entry. This forces sendmail to process your mailqueue as soon as the connection to the 'net is established. I am assuming that you have an account for user on bsd.home. In the home directory of user on bsd.home, create a .fetchmailrc file: poll example.net protocol pop3 fetchall pass MySecret This file should not be readable by anyone except user as it contains the password MySecret. In order to send mail with the correct from: header, you must tell sendmail to use user@example.net rather than user@bsd.home. You may also wish to tell sendmail to send all mail via relay.example.net, allowing quicker mail transmission. The following .mc file should suffice: VERSIONID(`bsd.home.mc version 1.0') OSTYPE(bsd4.4)dnl FEATURE(nouucp)dnl MAILER(local)dnl MAILER(smtp)dnl Cwlocalhost Cwbsd.home MASQUERADE_AS(`example.net')dnl FEATURE(allmasquerade)dnl FEATURE(masquerade_envelope)dnl FEATURE(nocanonify)dnl FEATURE(nodns)dnl define(`SMART_HOST', `relay.example.net') Dmbsd.home define(`confDOMAIN_NAME',`bsd.home')dnl define(`confDELIVERY_MODE',`deferred')dnl Refer to the previous section for details of how to turn this .mc file into a sendmail.cf file. Also, do not forget to restart sendmail after updating sendmail.cf. What other mail-server software can I use, instead of Sendmail? Sendmail is the default mail-server software for FreeBSD, but you can easily replace it with one of the other MTA (for instance, an MTA installed from the ports). There are various alternative MTA's in the ports tree already, with mail/exim, mail/postfix, mail/qmail, mail/zmailer, being some of the most popular choices. Diversity is nice, and the fact that you have many different mail-servers to chose from is considered a good thing; therefore try to avoid asking questions like Is Sendmail better than Qmail? in the mailing lists. If you do feel like asking, first check the mailing list archives. The advantages and disadvantages of each and every one of the available MTA's have already been discussed a few times. I have forgotten the root password! What do I do? Do not Panic! Simply restart the system, type boot -s at the Boot: prompt (just -s for FreeBSD releases before 3.2) to enter Single User mode. At the question about the shell to use, hit ENTER. You will be dropped to a &prompt.root; prompt. Enter mount -u / to remount your root filesystem read/write, then run mount -a to remount all the filesystems. Run passwd root to change the root password then run &man.exit.1; to continue booting. How do I keep ControlAltDelete from rebooting the system? If you are using syscons (the default console driver) in FreeBSD 2.2.7-RELEASE or later, build and install a new kernel with the line options SC_DISABLE_REBOOT in the configuration file. If you use the PCVT console driver in FreeBSD 2.2.5-RELEASE or later, use the following kernel configuration line instead: options PCVT_CTRL_ALT_DEL For older versions of FreeBSD, edit the keymap you are using for the console and replace the boot keywords with nop. The default keymap is /usr/share/syscons/keymaps/us.iso.kbd. You may have to instruct /etc/rc.conf to load this keymap explicitly for the change to take effect. Of course if you are using an alternate keymap for your country, you should edit that one instead. How do I reformat DOS text files to Unix ones? Simply use this perl command: &prompt.user; perl -i.bak -npe 's/\r\n/\n/g' file ... file is the file(s) to process. The modification is done in-place, with the original file stored with a .bak extension. Alternatively you can use the &man.tr.1; command: &prompt.user; tr -d '\r' < dos-text-file > unix-file dos-text-file is the file containing DOS text while unix-file will contain the converted output. This can be quite a bit faster than using perl. How do I kill processes by name? Use &man.killall.1;. Why is su bugging me about not being in root's ACL? The error comes from the Kerberos distributed authentication system. The problem is not fatal but annoying. You can either run su with the -K option, or uninstall Kerberos as described in the next question. How do I uninstall Kerberos? To remove Kerberos from the system, reinstall the bin distribution for the release you are running. If you have the CDROM, you can mount the cd (we will assume on /cdrom) and run &prompt.root; cd /cdrom/bin &prompt.root; ./install.sh Alternately, you can remove all "MAKE_KERBEROS" options from /etc/make.conf and rebuild world. How do I add pseudoterminals to the system? If you have lots of telnet, ssh, X, or screen users, you will probably run out of pseudoterminals. Here is how to add more: Build and install a new kernel with the line pseudo-device pty 256 in the configuration file. Run the commands &prompt.root; cd /dev &prompt.root; sh MAKEDEV pty{1,2,3,4,5,6,7} to make 256 device nodes for the new terminals. Edit /etc/ttys and add lines for each of the 256 terminals. They should match the form of the existing entries, i.e. they look like ttyqc none network The order of the letter designations is tty[pqrsPQRS][0-9a-v], using a regular expression. Reboot the system with the new kernel and you are ready to go. Why can I not create the snd0 device? There is no snd device. The name is used as a shorthand for the various devices that make up the FreeBSD sound driver, such as mixer, sequencer, and dsp. To create these devices you should &prompt.root; cd /dev &prompt.root; sh MAKEDEV snd0 How do I re-read /etc/rc.conf and re-start /etc/rc without a reboot? Go into single user mode and then back to multi user mode. On the console do: &prompt.root; shutdown now (Note: without -r or -h) &prompt.root; return &prompt.root; exit What is a sandbox? Sandbox is a security term. It can mean two things: A process which is placed inside a set of virtual walls that are designed to prevent someone who breaks into the process from being able to break into the wider system. The process is said to be able to play inside the walls. That is, nothing the process does in regards to executing code is supposed to be able to breech the walls so you do not have to do a detailed audit of its code to be able to say certain things about its security. The walls might be a userid, for example. This is the definition used in the security and named man pages. Take the ntalk service, for example (see /etc/inetd.conf). This service used to run as userid root. Now it runs as userid tty. The tty user is a sandbox designed to make it more difficult for someone who has successfully hacked into the system via ntalk from being able to hack beyond that user id. A process which is placed inside a simulation of the machine. This is more hard-core. Basically it means that someone who is able to break into the process may believe that he can break into the wider machine but is, in fact, only breaking into a simulation of that machine and not modifying any real data. The most common way to accomplish this is to build a simulated environment in a subdirectory and then run the processes in that directory chroot'd (i.e. / for that process is this directory, not the real / of the system). Another common use is to mount an underlying filesystem read-only and then create a filesystem layer on top of it that gives a process a seemingly writeable view into that filesystem. The process may believe it is able to write to those files, but only the process sees the effects - other processes in the system do not, necessarily. An attempt is made to make this sort of sandbox so transparent that the user (or hacker) does not realize that he is sitting in it. Unix implements two core sandboxes. One is at the process level, and one is at the userid level. Every Unix process is completely firewalled off from every other Unix process. One process cannot modify the address space of another. This is unlike Windows where a process can easily overwrite the address space of any other, leading to a crash. A Unix process is owned by a particular userid. If the userid is not the root user, it serves to firewall the process off from processes owned by other users. The userid is also used to firewall off on-disk data. What is securelevel? The securelevel is a security mechanism implemented in the kernel. Basically, when the securelevel is positive, the kernel restricts certain tasks; not even the superuser (i.e., root) is allowed to do them. At the time of this writing, the securelevel mechanism is capable of, among other things, limiting the ability to, unset certain file flags, such as schg (the system immutable flag), write to kernel memory via /dev/mem and /dev/kmem, load kernel modules, and alter &man.ipfirewall.4; rules. To check the status of the securelevel on a running system, simply execute the following command: &prompt.root; sysctl kern.securelevel The output will contain the name of the &man.sysctl.8; variable (in this case, kern.securelevel) and a number. The latter is the current value of the securelevel. If it is positive (i.e., greater than 0), at least some of the securelevel's protections are enabled. You cannot lower the securelevel of a running system; being able to do that would defeat its purpose. If you need to do a task that requires that the securelevel be non-positive (e.g., an installworld or changing the date), you will have to change the securelevel setting in /etc/rc.conf (you want to look for the kern_securelevel and kern_securelevel_enable variables) and reboot. For more information on securelevel and the specific things all the levels do, please consult the &man.init.8; manual page. Securelevel is not a silver bullet; it has many known deficiencies. More often than not, it provides a false sense of security. One of its biggest problems is that in order for it to be at all effective, all files used in the boot process up until the securelevel is set must be protected. If an attacker can get the system to execute their code prior to the securelevel being set (which happens quite late in the boot process since some things the system must do at start-up cannot be done at an elevated securelevel), its protections are invalidated. While this task of protecting all files used in the boot process is not technically impossible, if it is achieved, system maintenance will become a nightmare since one would have to take the system down, at least to single-user mode, to modify a configuration file. This point and others are often discussed on the mailing lists, particularly freebsd-security. Please search the archives here for an extensive discussion. Some people are hopeful that securelevel will soon go away in favor of a more fine-grained mechanism, but things are still hazy in this respect. Consider yourself warned. I tried to update my system to the latest -STABLE, but got -RC or -PRERELEASE! What is going on? Short answer: it is just a name. RC stands for Release Candidate. It signifies that a release is imminent. In FreeBSD, -PRERELEASE is typically synonymous with the code freeze before a release. (For some releases, the -BETA label was used in the same way as -PRERELEASE.) Long answer: FreeBSD derives its releases from one of two places. Major, dot-zero, releases, such as 3.0-RELEASE and 4.0-RELEASE, are branched from the head of the development stream, commonly referred to as -CURRENT. Minor releases, such as 3.1-RELEASE or 4.2-RELEASE, have been snapshots of the active -STABLE branch. Starting with 4.3-RELEASE, each release also now has its own branch which can be tracked by people requiring an extremely conservative rate of development (typically only security advisories). When a release is about to be made, the branch from which it will be derived from has to undergo a certain process. Part of this process is a code freeze. When a code freeze is initiated, the name of the branch is changed to reflect that it is about to become a release. For example, if the branch used to be called 4.5-STABLE, its name will be changed to 4.6-PRERELEASE to signify the code freeze and signify that extra pre-release testing should be happening. Bug fixes can still be committed to be part of the release. When the source code is in shape for the release the name will be changed to 4.6-RC to signify that a release is about to be made from it. Once in the RC stage, only the most critical bugs found can be fixed. Once the release (4.6-RELEASE in this example) and release branch have been made, the branch will be renamed to 4.6-STABLE. For more information on version numbers and the various CVS branches, refer to the Release Engineering article. I tried to install a new kernel, and the chflags failed. How do I get around this? Short answer: You are probably at security level greater than 0. Reboot directly to single user mode to install the kernel. Long answer: FreeBSD disallows changing system flags at security levels greater than 0. You can check your security level with the command: &prompt.root; sysctl kern.securelevel You cannot lower the security level; you have to boot to single mode to install the kernel, or change the security level in /etc/rc.conf then reboot. See the &man.init.8; man page for details on securelevel, and see /etc/defaults/rc.conf and the &man.rc.conf.5; man page for more information on rc.conf. I cannot change the time on my system by more than one second! How do I get around this? Short answer: You are probably at security level greater than 1. Reboot directly to single user mode to change the date. Long answer: FreeBSD disallows changing the time by more that one second at security levels greater than 1. You can check your security level with the command: &prompt.root; sysctl kern.securelevel You cannot lower the security level; you have to boot to single mode to change the date, or change the security level in /etc/rc.conf then reboot. See the &man.init.8; man page for details on securelevel, and see /etc/defaults/rc.conf and the &man.rc.conf.5; man page for more information on rc.conf. Why is rpc.statd using 256 megabytes of memory? No, there is no memory leak, and it is not using 256 Mbytes of memory. It simply likes to (i.e., always does) map an obscene amount of memory into its address space for convenience. There is nothing terribly wrong with this from a technical standpoint; it just throws off things like &man.top.1; and &man.ps.1;. &man.rpc.statd.8; maps its status file (resident on /var) into its address space; to save worrying about remapping it later when it needs to grow, it maps it with a generous size. This is very evident from the source code, where one can see that the length argument to &man.mmap.2; is 0x10000000, or one sixteenth of the address space on an IA32, or exactly 256MB. Why can I not unset the schg file flag? You are running at an elevated (i.e., greater than 0) securelevel. Lower the securelevel and try again. For more information, see the FAQ entry on securelevel and the &man.init.8; manual page. Why does SSH authentication through .shosts not work by default in recent versions of FreeBSD? The reason why .shosts authentication does not work by default in more recent versions of FreeBSD is because &man.ssh.1; is not installed suid root by default. To fix this, you can do one of the following: As a permanent fix, set ENABLE_SUID_SSH to true in /etc/make.conf and rebuild ssh (or run make world). As a temporary fix, change the mode on /usr/bin/ssh to 4555 by running chmod 4755 /usr/bin/ssh as root. Then add ENABLE_SUID_SSH= true to /etc/make.conf so the change takes effect the next time make world is run. What is vnlru? vnlru flushes and frees vnodes when the system hits the kern.maxvnodes limit. This kernel thread sits mostly idle, and only activates if you have a huge amount of RAM and are accessing tens of thousands of tiny files. The X Window System and Virtual Consoles I want to run X, how do I go about it? The easiest way is to simply specify that you want to run X during the installation process. Then read and follow the documentation on the xf86config tool, which assists you in configuring XFree86 for your particular graphics card/mouse/etc. You may also wish to investigate the Xaccel server. See the section on Xi Graphics or Metro Link for more details. I tried to run X, but I get an KDENABIO failed (Operation not permitted) error when I type startx. What do I do now? Your system is running at a raised securelevel, is not it? It is, indeed, impossible to start X at a raised securelevel. To see why, look at the &man.init.8; man page. So the question is what else you should do instead, and you basically have two choices: set your securelevel back down to zero (usually from /etc/rc.conf), or run &man.xdm.1; at boot time (before the securelevel is raised). See for more information about running &man.xdm.1; at boot time. Why does my mouse not work with X? If you are using syscons (the default console driver), you can configure FreeBSD to support a mouse pointer on each virtual screen. In order to avoid conflicting with X, syscons supports a virtual device called /dev/sysmouse. All mouse events received from the real mouse device are written to the sysmouse device via moused. If you wish to use your mouse on one or more virtual consoles, and use X, see and set up moused. Then edit /etc/XF86Config and make sure you have the following lines. Section Pointer Protocol "SysMouse" Device "/dev/sysmouse" ..... The above example is for XFree86 3.3.2 or later. For earlier versions, the Protocol should be MouseSystems. Some people prefer to use /dev/mouse under X. To make this work, /dev/mouse should be linked to /dev/sysmouse (see &man.sysmouse.4;): &prompt.root; cd /dev &prompt.root; rm -f mouse &prompt.root; ln -s sysmouse mouse My mouse has a fancy wheel. Can I use it in X? Yes. But you need to customize X client programs. See Colas Nahaboo's web page (http://www.inria.fr/koala/colas/mouse-wheel-scroll/) . If you want to use the imwheel program, just follow these simple steps. Translate the Wheel Events The imwheel program works by translating mouse button 4 and mouse button 5 events into key events. Thus, you have to get the mouse driver to translate mouse wheel events to button 4 and 5 events. There are two ways of doing this, the first way is to have &man.moused.8; do the translation. The second way is for the X server itself to do the event translation. Using &man.moused.8; to Translate Wheel Events To have &man.moused.8; perform the event translations, simply add to the command line used to start &man.moused.8;. For example, if you normally start &man.moused.8; via moused -p /dev/psm0 you would start it by entering moused -p /dev/psm0 -z 4 instead. If you start &man.moused.8; automatically during bootup via /etc/rc.conf, you can simply add to the moused_flags variable in /etc/rc.conf. You now need to tell X that you have a 5 button mouse. To do this, simply add the line Buttons 5 to the Pointer section of /etc/XF86Config. For example, you might have the following Pointer section in /etc/XF86Config. <quote>Pointer</quote> Section for Wheeled Mouse in XFree86 3.3.x series XF86Config with moused Translation Section "Pointer" Protocol "SysMouse" Device "/dev/sysmouse" Buttons 5 EndSection <quote>InputDevice</quote> Section for Wheeled Mouse in XFree86 4.x series XF86Config with X Server Translation Section "InputDevice" Identifier "Mouse1" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/sysmouse" Option "Buttons" "5" EndSection <quote>.emacs</quote> example for naive page scrolling with Wheeled Mouse ;; wheel mouse (global-set-key [mouse-4] 'scroll-down) (global-set-key [mouse-5] 'scroll-up) Using Your X Server to Translate the Wheel Events If you are not running &man.moused.8;, or if you do not want &man.moused.8; to translate your wheel events, you can have the X server do the event translation instead. This requires a couple of modifications to your /etc/XF86Config file. First, you need to choose the proper protocol for your mouse. Most wheeled mice use the IntelliMouse protocol. However, XFree86 does support other protocols, such as MouseManPlusPS/2 for the Logitech MouseMan+ mice. Once you have chosen the protocol you will use, you need to add a Protocol line to the Pointer section. Secondly, you need to tell the X server to remap wheel scroll events to mouse buttons 4 and 5. This is done with the ZAxisMapping option. For example, if you are not using &man.moused.8;, and you have an IntelliMouse attached to the PS/2 mouse port you would use the following in /etc/XF86Config. <quote>Pointer</quote> Section for Wheeled Mouse in <filename>XF86Config</filename> with X Server Translation Section "Pointer" Protocol "IntelliMouse" Device "/dev/psm0" ZAxisMapping 4 5 EndSection <quote>InputDevice</quote> Section for Wheeled Mouse in XFree86 4.x series XF86Config with X Server Translation Section "InputDevice" Identifier "Mouse1" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psm0" Option "ZAxisMapping" "4 5" EndSection <quote>.emacs</quote> example for naive page scrolling with Wheeled Mouse ;; wheel mouse (global-set-key [mouse-4] 'scroll-down) (global-set-key [mouse-5] 'scroll-up) Install imwheel Next, install imwheel from the Ports collection. It can be found in the x11 category. This program will map the wheel events from your mouse into keyboard events. For example, it might send Page Up to a program when you scroll the wheel forwards. Imwheel uses a configuration file to map the wheel events to key presses so that it can send different keys to different applications. The default imwheel configuration file is installed in /usr/X11R6/etc/imwheelrc. You can copy it to ~/.imwheelrc and then edit it if you wish to customize imwheel's configuration. The format of the configuration file is documented in &man.imwheel.1;. Configure Emacs to Work with Imwheel (optional) If you use emacs or Xemacs, then you need to add a small section to your ~/.emacs file. For emacs, add the following: <application>Emacs</application> Configuration for <application>Imwheel</application> ;;; For imwheel (setq imwheel-scroll-interval 3) (defun imwheel-scroll-down-some-lines () (interactive) (scroll-down imwheel-scroll-interval)) (defun imwheel-scroll-up-some-lines () (interactive) (scroll-up imwheel-scroll-interval)) (global-set-key [?\M-\C-\)] 'imwheel-scroll-up-some-lines) (global-set-key [?\M-\C-\(] 'imwheel-scroll-down-some-lines) ;;; end imwheel section For Xemacs, add the following to your ~/.emacs file instead: <application>Xemacs</application> Configuration for <application>Imwheel</application> ;;; For imwheel (setq imwheel-scroll-interval 3) (defun imwheel-scroll-down-some-lines () (interactive) (scroll-down imwheel-scroll-interval)) (defun imwheel-scroll-up-some-lines () (interactive) (scroll-up imwheel-scroll-interval)) (define-key global-map [(control meta \))] 'imwheel-scroll-up-some-lines) (define-key global-map [(control meta \()] 'imwheel-scroll-down-some-lines) ;;; end imwheel section Run Imwheel You can just type imwheel in an xterm to start it up once it is installed. It will background itself and take effect immediately. If you want to always use imwheel, simply add it to your .xinitrc or .xsession file. You can safely ignore any warnings imwheel displays about PID files. Those warnings only apply to the Linux version of imwheel. Why do X Window menus and dialog boxes not work right? Try turning off the Num Lock key. If your Num Lock key is on by default at boot-time, you may add the following line in the Keyboard section of the XF86Config file. # Let the server do the NumLock processing. This should only be # required when using pre-R6 clients ServerNumLock What is a virtual console and how do I make more? Virtual consoles, put simply, enable you to have several simultaneous sessions on the same machine without doing anything complicated like setting up a network or running X. When the system starts, it will display a login prompt on the monitor after displaying all the boot messages. You can then type in your login name and password and start working (or playing!) on the first virtual console. At some point, you will probably wish to start another session, perhaps to look at documentation for a program you are running or to read your mail while waiting for an FTP transfer to finish. Just do AltF2 (hold down the Alt key and press the F2 key), and you will find a login prompt waiting for you on the second virtual console! When you want to go back to the original session, do AltF1. The default FreeBSD installation has three virtual consoles enabled (8 starting with 3.3-RELEASE), and AltF1, AltF2, and AltF3 will switch between these virtual consoles. To enable more of them, edit /etc/ttys (see &man.ttys.5;) and add entries for ttyv4 to ttyvc after the comment on Virtual terminals: # Edit the existing entry for ttyv3 in /etc/ttys and change # "off" to "on". ttyv3 "/usr/libexec/getty Pc" cons25 on secure ttyv4 "/usr/libexec/getty Pc" cons25 on secure ttyv5 "/usr/libexec/getty Pc" cons25 on secure ttyv6 "/usr/libexec/getty Pc" cons25 on secure ttyv7 "/usr/libexec/getty Pc" cons25 on secure ttyv8 "/usr/libexec/getty Pc" cons25 on secure ttyv9 "/usr/libexec/getty Pc" cons25 on secure ttyva "/usr/libexec/getty Pc" cons25 on secure ttyvb "/usr/libexec/getty Pc" cons25 on secure Use as many or as few as you want. The more virtual terminals you have, the more resources that are used; this can be important if you have 8MB RAM or less. You may also want to change the secure to insecure. If you want to run an X server you must leave at least one virtual terminal unused (or turned off) for it to use. That is to say that if you want to have a login prompt pop up for all twelve of your Alt-function keys, you are out of luck - you can only do this for eleven of them if you also want to run an X server on the same machine. The easiest way to disable a console is by turning it off. For example, if you had the full 12 terminal allocation mentioned above and you wanted to run X, you would change settings for virtual terminal 12 from: ttyvb "/usr/libexec/getty Pc" cons25 on secure to: ttyvb "/usr/libexec/getty Pc" cons25 off secure If your keyboard has only ten function keys, you would end up with: ttyv9 "/usr/libexec/getty Pc" cons25 off secure ttyva "/usr/libexec/getty Pc" cons25 off secure ttyvb "/usr/libexec/getty Pc" cons25 off secure (You could also just delete these lines.) Once you have edited /etc/ttys, the next step is to make sure that you have enough virtual terminal devices. The easiest way to do this is: &prompt.root; cd /dev &prompt.root; sh MAKEDEV vty12 Next, the easiest (and cleanest) way to activate the virtual consoles is to reboot. However, if you really do not want to reboot, you can just shut down the X Window system and execute (as root): &prompt.root; kill -HUP 1 It is imperative that you completely shut down X Window if it is running, before running this command. If you do not, your system will probably appear to hang/lock up after executing the kill command. How do I access the virtual consoles from X? Use Ctrl Alt Fn to switch back to a virtual console. Ctrl Alt F1 would return you to the first virtual console. Once you are back to a text console, you can then use Alt Fn as normal to move between them. To return to the X session, you must switch to the virtual console running X. If you invoked X from the command line, (e.g., using startx) then the X session will attach to the next unused virtual console, not the text console from which it was invoked. If you have eight active virtual terminals then X will be running on the ninth, and you would use Alt F9 to return. How do I start XDM on boot? There are two schools of thought on how to start xdm. One school starts xdm from /etc/ttys (see &man.ttys.5;) using the supplied example, while the other simply runs xdm from rc.local (see &man.rc.8;) or from a X.sh script in /usr/local/etc/rc.d. Both are equally valid, and one may work in situations where the other does not. In both cases the result is the same: X will pop up a graphical login: prompt. The ttys method has the advantage of documenting which vty X will start on and passing the responsibility of restarting the X server on logout to init. The rc.local method makes it easy to kill xdm if there is a problem starting the X server. If loaded from rc.local, xdm should be started without any arguments (i.e., as a daemon). xdm must start AFTER getty runs, or else getty and xdm will conflict, locking out the console. The best way around this is to have the script sleep 10 seconds or so then launch xdm. If you are to start xdm from /etc/ttys, there still is a chance of conflict between xdm and &man.getty.8;. One way to avoid this is to add the vt number in the /usr/X11R6/lib/X11/xdm/Xservers file. :0 local /usr/X11R6/bin/X vt4 The above example will direct the X server to run in /dev/ttyv3. Note the number is offset by one. The X server counts the vty from one, whereas the FreeBSD kernel numbers the vty from zero. Why do I get Couldn't open console when I run xconsole? If you start X with startx, the permissions on /dev/console will not get changed, resulting in things like xterm -C and xconsole not working. This is because of the way console permissions are set by default. On a multi-user system, one does not necessarily want just any user to be able to write on the system console. For users who are logging directly onto a machine with a VTY, the &man.fbtab.5; file exists to solve such problems. In a nutshell, make sure an uncommented line of the form /dev/ttyv0 0600 /dev/console is in /etc/fbtab (see &man.fbtab.5;) and it will ensure that whomever logs in on /dev/ttyv0 will own the console. Before, I was able to run XFree86 as a regular user. Why does it now say that I must be root? All X servers need to be run as root in order to get direct access to your video hardware. Older versions of XFree86 (<= 3.3.6) installed all bundled servers to be automatically run as root (setuid to root). This is obviously a security hazard because X servers are large, complicated programs. Newer versions of XFree86 do not install the servers setuid to root for just this reason. Obviously, running an X server as the root user is not acceptable, nor a good idea security-wise. There are two ways to be able to use X as a regular user. The first is to use xdm or another display manager (e.g., kdm); the second is to use the Xwrapper. xdm is a daemon that handles graphical logins. It is usually started at boot time, and is responsible for authenticating users and starting their sessions; it is essentially the graphical counterpart of &man.getty.8; and &man.login.1;. For more information on xdm see the XFree86 documentation, and the the FAQ entry on it. Xwrapper is the X server wrapper; it is a small utility to enable one to manually run an X server while maintaining reasonable safety. It performs some sanity checks on the command line arguments given, and if they pass, runs the appropriate X server. If you do not want to run a display manger for whatever reason, this is for you. If you have installed the complete ports collection, you can find the port in /usr/ports/x11/wrapper. Why does my PS/2 mouse misbehave under X? Your mouse and the mouse driver may have somewhat become out of synchronization. In versions 2.2.5 and earlier, switching away from X to a virtual terminal and getting back to X again may make them re-synchronized. If the problem occurs often, you may add the following option in your kernel configuration file and recompile it. options PSM_CHECKSYNC See the section on building a kernel if you have no experience with building kernels. With this option, there should be less chance of synchronization problem between the mouse and the driver. If, however, you still see the problem, click any mouse button while holding the mouse still to re-synchronize the mouse and the driver. Note that unfortunately this option may not work with all the systems and voids the tap feature of the ALPS GlidePoint device attached to the PS/2 mouse port. In versions 2.2.6 and later, synchronization check is done in a slightly better way and is standard in the PS/2 mouse driver. It should even work with GlidePoint. (As the check code has become a standard feature, PSM_CHECKSYNC option is not available in these versions.) However, in rare case the driver may erroneously report synchronization problem and you may see the kernel message: psmintr: out of sync (xxxx != yyyy) and find your mouse does not seem to work properly. If this happens, disable the synchronization check code by setting the driver flags for the PS/2 mouse driver to 0x100. Enter UserConfig by giving the option at the boot prompt: boot: -c Then, in the UserConfig command line, type: UserConfig> flags psm0 0x100 UserConfig> quit Why does my PS/2 mouse from MouseSystems not work? There have been some reports that certain model of PS/2 mouse from MouseSystems works only if it is put into the high resolution mode. Otherwise, the mouse cursor may jump to the upper-left corner of the screen every so often. Unfortunately there is no workaround for versions 2.0.X and 2.1.X. In versions 2.2 through 2.2.5, apply the following patch to /sys/i386/isa/psm.c and rebuild the kernel. See the section on building a kernel if you have no experience with building kernels. @@ -766,6 +766,8 @@ if (verbose >= 2) log(LOG_DEBUG, "psm%d: SET_DEFAULTS return code:%04x\n", unit, i); + set_mouse_resolution(sc->kbdc, PSMD_RES_HIGH); + #if 0 set_mouse_scaling(sc->kbdc); /* 1:1 scaling */ set_mouse_mode(sc->kbdc); /* stream mode */ In versions 2.2.6 or later, specify the flags 0x04 to the PS/2 mouse driver to put the mouse into the high resolution mode. Enter UserConfig by giving the option at the boot prompt: boot: -c Then, in the UserConfig command line, type: UserConfig> flags psm0 0x04 UserConfig> quit See the previous section for another possible cause of mouse problems. When building an X app, imake cannot find Imake.tmpl. Where is it? Imake.tmpl is part of the Imake package, a standard X application building tool. Imake.tmpl, as well as several header files that are required to build X apps, is contained in the X prog distribution. You can install this from sysinstall or manually from the X distribution files. An X app I am building depends on XFree86 3.3.x, but I have XFree86 4.x installed. What should I do? To tell the port build to link to the XFree86 4.x libraries, add the following to /etc/make.conf, (if you do not have this file, create it): XFREE86_VERSION= 4 How do I reverse the mouse buttons? Run the command xmodmap -e "pointer = 3 2 1" from your .xinitrc or .xsession. How do I install a splash screen and where do I find them? Just prior to the release of FreeBSD 3.1, a new feature was added to allow the display of splash screens during the boot messages. The splash screens currently must be a 256 color bitmap (*.BMP) or ZSoft PCX (*.PCX) file. In addition, they must have a resolution of 320x200 or less to work on standard VGA adapters. If you compile VESA support into your kernel, then you can use larger bitmaps up to 1024x768. Note that VESA support requires the VM86 kernel option to be compiled into the kernel. The actual VESA support can either be compiled directly into the kernel with the VESA kernel config option or by loading the VESA kld module during bootup. To use a splash screen, you need to modify the startup files that control the boot process for FreeBSD. The files for this changed prior to the release of FreeBSD 3.2, so there are now two ways of loading a splash screen: FreeBSD 3.1 The first step is to find a bitmap version of your splash screen. Release 3.1 only supports Windows bitmap splash screens. Once you have found your splash screen of choice copy it to /boot/splash.bmp. Next, you need to have a /boot/loader.rc file that contains the following lines: load kernel load -t splash_image_data /boot/splash.bmp load splash_bmp autoboot FreeBSD 3.2+ In addition to adding support for PCX splash screens, FreeBSD 3.2 includes a nicer way of configuring the boot process. If you wish, you can use the method listed above for FreeBSD 3.1. If you do and you want to use PCX, replace splash_bmp with splash_pcx. If, on the other hand, you want to use the newer boot configuration, you need to create a /boot/loader.rc file that contains the following lines: include /boot/loader.4th start and a /boot/loader.conf that contains the following: splash_bmp_load="YES" bitmap_load="YES" This assumes you are using /boot/splash.bmp for your splash screen. If you would rather use a PCX file, copy it to /boot/splash.pcx, create a /boot/loader.rc as instructed above, and create a /boot/loader.conf that contains: splash_pcx_load="YES" bitmap_load="YES" bitmap_name="/boot/splash.pcx" Now all you need is a splash screen. For that you can surf on over to the gallery at http://www.baldwin.cx/splash/. Can I use the Windows keys on my keyboard in X? Yes. All you need to do is use &man.xmodmap.1; to define what function you wish them to perform. Assuming all Windows keyboards are standard then the keycodes for the 3 keys are 115 - Windows key, between the left-hand Ctrl and Alt keys 116 - Windows key, to the right of the AltGr key 117 - Menu key, to the left of the right-hand Ctrl key To have the left Windows key print a comma, try this. &prompt.root; xmodmap -e "keycode 115 = comma" You will probably have to re-start your window manager to see the result. To have the Windows key-mappings enabled automatically every time you start X either put the xmodmap commands in your ~/.xinitrc file or, preferably, create a file ~/.xmodmaprc and include the xmodmap options, one per line, then add the line xmodmap $HOME/.xmodmaprc to your ~/.xinitrc. For example, you could map the 3 keys to be F13, F14, and F15, respectively. This would make it easy to map them to useful functions within applications or your window manager, as demonstrated further down. To do this put the following in ~/.xmodmaprc. keycode 115 = F13 keycode 116 = F14 keycode 117 = F15 If you use fvwm2, for example, you could map the keys so that F13 iconifies (or de-iconifies) the window the cursor is in, F14 brings the window the cursor is in to the front or, if it is already at the front, pushes it to the back, and F15 pops up the main Workplace (application) menu even if the cursor is not on the desktop, which is useful if you do not have any part of the desktop visible (and the logo on the key matches its functionality). The following entries in ~/.fvwmrc implement the aforementioned setup: Key F13 FTIWS A Iconify Key F14 FTIWS A RaiseLower Key F15 A A Menu Workplace Nop How can I get 3D hardware acceleration for OpenGL? The availability of 3D acceleration depends on the version of XFree86 you are using and the type of video chip you have. If you have an NVIDIA chip, check out the FreeBSD NVIDIA Driver Initiative page, which discusses 3D acceleration for NVIDIA chips using XFree86-4. For other cards with XFree86-4, including the Matrox G200/G400, ATI Rage 128/Radeon, and 3dfx Voodoo 3, 4, 5, and Banshee, information on hardware acceleration is available on the XFree86-4 Direct Rendering on FreeBSD page. Users of XFree86 version 3.3 can use the Utah-GLX port found in graphics/utah-glx to get limited accelerated OpenGL on the Matrox Gx00, ATI Rage Pro, SiS 6326, i810, Savage, and older NVIDIA chips. Networking Where can I get information on diskless booting? Diskless booting means that the FreeBSD box is booted over a network, and reads the necessary files from a server instead of its hard disk. For full details, please read the Handbook entry on diskless booting Can a FreeBSD box be used as a dedicated network router? Yes. Please see the Handbook entry on advanced networking, specifically the section on routing and gateways. Can I connect my Win95 box to the Internet via FreeBSD? Typically, people who ask this question have two PC's at home, one with FreeBSD and one with Win95; the idea is to use the FreeBSD box to connect to the Internet and then be able to access the Internet from the Windows95 box through the FreeBSD box. This is really just a special case of the previous question. ... and the answer is yes! In FreeBSD 3.x, user-mode &man.ppp.8; contains a option. If you run &man.ppp.8; with the , set gateway_enable to YES in /etc/rc.conf, and configure your Windows machine correctly, this should work fine. More detailed information about setting this up can be found in the Pedantic PPP Primer by Steve Sims. If you are using kernel-mode PPP, or have an Ethernet connection to the Internet, you will have to use &man.natd.8;. Please look at the natd section of this FAQ. Does FreeBSD support SLIP and PPP? Yes. See the manual pages for &man.slattach.8;, &man.sliplogin.8;, &man.ppp.8;, and &man.pppd.8;. &man.ppp.8; and &man.pppd.8; provide support for both incoming and outgoing connections, while &man.sliplogin.8; deals exclusively with incoming connections, and &man.slattach.8; deals exclusively with outgoing connections. For more information on how to use these, please see the Handbook chapter on PPP and SLIP. If you only have access to the Internet through a shell account, you may want to have a look at the net/slirp package. It can provide you with (limited) access to services such as ftp and http direct from your local machine. Does FreeBSD support NAT or Masquerading? If you have a local subnet (one or more local machines), but have been allocated only a single IP number from your Internet provider (or even if you receive a dynamic IP number), you may want to look at the &man.natd.8; program. &man.natd.8; allows you to connect an entire subnet to the Internet using only a single IP number. The &man.ppp.8; program has similar functionality built in via the switch. The alias library (&man.libalias.3;) is used in both cases. How do I connect two FreeBSD systems over a parallel line using PLIP? Please see the PLIP section of the Handbook. Why can I not create a /dev/ed0 device? Because they aren't necessary. In the Berkeley networking framework, network interfaces are only directly accessible by kernel code. Please see the /etc/rc.network file and the manual pages for the various network programs mentioned there for more information. If this leaves you totally confused, then you should pick up a book describing network administration on another BSD-related operating system; with few significant exceptions, administering networking on FreeBSD is basically the same as on SunOS 4.0 or Ultrix. How can I set up Ethernet aliases? If the alias is on the same subnet as an address already configured on the interface, then add netmask 0xffffffff to your &man.ifconfig.8; command-line, as in the following: &prompt.root; ifconfig ed0 alias 192.0.2.2 netmask 0xffffffff Otherwise, just specify the network address and netmask as usual: &prompt.root; ifconfig ed0 alias 172.16.141.5 netmask 0xffffff00 How do I get my 3C503 to use the other network port? If you want to use the other ports, you will have to specify an additional parameter on the &man.ifconfig.8; command line. The default port is link0. To use the AUI port instead of the BNC one, use link2. These flags should be specified using the ifconfig_* variables in /etc/rc.conf (see &man.rc.conf.5;). Why am I having trouble with NFS and FreeBSD? Certain PC network cards are better than others (to put it mildly) and can sometimes cause problems with network intensive applications like NFS. See the Handbook entry on NFS for more information on this topic. Why can I not NFS-mount from a Linux box? Some versions of the Linux NFS code only accept mount requests from a privileged port; try &prompt.root; mount -o -P linuxbox:/blah /mnt Why can I not NFS-mount from a Sun box? Sun workstations running SunOS 4.X only accept mount requests from a privileged port; try &prompt.root; mount -o -P sunbox:/blah /mnt Why does mountd keep telling me it can't change attributes and that I have a bad exports list on my FreeBSD NFS server? The most frequent problem is not understanding the correct format of /etc/exports. Please review &man.exports.5; and the NFS entry in the Handbook, especially the section on configuring NFS. Why am I having problems talking PPP to NeXTStep machines? Try disabling the TCP extensions in /etc/rc.conf (see &man.rc.conf.5;) by changing the following variable to NO: tcp_extensions=NO Xylogic's Annex boxes are also broken in this regard and you must use the above change to connect thru them. How do I enable IP multicast support? Multicast host operations are fully supported in FreeBSD 2.0 and later by default. If you want your box to run as a multicast router, you will need to recompile your kernel with the MROUTING option and run &man.mrouted.8;. FreeBSD 2.2 and later will start &man.mrouted.8; at boot time if the flag mrouted_enable is set to "YES" in /etc/rc.conf. MBONE tools are available in their own ports category, mbone. If you are looking for the conference tools vic and vat, look there! Which network cards are based on the DEC PCI chipset? Here is a list compiled by Glen Foster gfoster@driver.nsta.org, with some more modern additions: Network cards based on the DEC PCI chipset Vendor Model ASUS PCI-L101-TB Accton ENI1203 Cogent EM960PCI Compex ENET32-PCI D-Link DE-530 Dayna DP1203, DP2100 DEC DE435, DE450 Danpex EN-9400P3 JCIS Condor JC1260 Linksys EtherPCI Mylex LNP101 SMC EtherPower 10/100 (Model 9332) SMC EtherPower (Model 8432) TopWare TE-3500P Znyx (2.2.x) ZX312, ZX314, ZX342, ZX345, ZX346, ZX348 Znyx (3.x) ZX345Q, ZX346Q, ZX348Q, ZX412Q, ZX414, ZX442, ZX444, ZX474, ZX478, ZX212, ZX214 (10mbps/hd)
Why do I have to use the FQDN for hosts on my site? You will probably find that the host is actually in a different domain; for example, if you are in foo.example.org and you wish to reach a host called mumble in the example.org domain, you will have to refer to it by the fully-qualified domain name, mumble.example.org, instead of just mumble. Traditionally, this was allowed by BSD BIND resolvers. However the current version of bind (see &man.named.8;) that ships with FreeBSD no longer provides default abbreviations for non-fully qualified domain names other than the domain you are in. So an unqualified host mumble must either be found as mumble.foo.example.org, or it will be searched for in the root domain. This is different from the previous behavior, where the search continued across mumble.example.org, and mumble.edu. Have a look at RFC 1535 for why this was considered bad practice, or even a security hole. As a good workaround, you can place the line search foo.example.org example.org instead of the previous domain foo.example.org into your /etc/resolv.conf file (see &man.resolv.conf.5;). However, make sure that the search order does not go beyond the boundary between local and public administration, as RFC 1535 calls it. Why do I get an error, Permission denied, for all networking operations? If you have compiled your kernel with the IPFIREWALL option, you need to be aware that the default policy as of 2.1.7R (this actually changed during 2.1-STABLE development) is to deny all packets that are not explicitly allowed. If you had unintentionally misconfigured your system for firewalling, you can restore network operability by typing the following while logged in as root: &prompt.root; ipfw add 65534 allow all from any to any You can also set firewall_type="open" in /etc/rc.conf. For further information on configuring a FreeBSD firewall, see the Handbook section. How much overhead does IPFW incur? Please see the Handbook's Firewalls section, specifically the section on IPFW Overhead & Optimization. Why is my ipfw fwd rule to redirect a service to another machine not working? Possibly because you want to do network address translation (NAT) and not just forward packets. A fwd rule does exactly what it says; it forwards packets. It does not actually change the data inside the packet. Say we have a rule like: 01000 fwd 10.0.0.1 from any to foo 21 When a packet with a destination address of foo arrives at the machine with this rule, the packet is forwarded to 10.0.0.1, but it still has the destination address of foo! The destination address of the packet is not changed to 10.0.0.1. Most machines would probably drop a packet that they receive with a destination address that is not their own. Therefore, using a fwd rule does not often work the way the user expects. This behavior is a feature and not a bug. See the FAQ about redirecting services, the &man.natd.8; manual, or one of the several port redirecting utilities in the ports collection for a correct way to do this. How can I redirect service requests from one machine to another? You can redirect FTP (and other service) request with the socket package, available in the ports tree in category sysutils. Simply replace the service's command line to call socket instead, like so: ftp stream tcp nowait nobody /usr/local/bin/socket socket ftp.example.com ftp where ftp.example.com and ftp are the host and port to redirect to, respectively. Where can I get a bandwidth management tool? There are three bandwidth management tools available for FreeBSD. &man.dummynet.4; is integrated into FreeBSD (or more specifically, &man.ipfw.4;); ALTQ is available for free; Bandwidth Manager from Emerging Technologies is a commercial product. Why do I get /dev/bpf0: device not configured? You are running a program that requires the Berkeley Packet Filter (&man.bpf.4;), but it's not in your kernel. Add this to your kernel config file and build a new kernel: pseudo-device bpf # Berkeley Packet Filter After rebooting, create the device node. This can be accomplished by going to the /dev directory and running: &prompt.root; sh MAKEDEV bpf0 Please see the Handbook entry on device nodes for more information on creating devices. How do I mount a disk from a Windows machine that is on my network, like smbmount in Linux? Use the SMBFS toolset. It includes a set of kernel modifications and a set of userland programs. The programs and information are available as net/smbfs in the ports collection, or in the base system as of 4.5-RELEASE and later. What are these messages about icmp-response bandwidth limit 300/200 pps in my log files? This is the kernel telling you that some activity is provoking it to send more ICMP or TCP reset (RST) responses than it thinks it should. ICMP responses are often generated as a result of attempted connections to unused UDP ports. TCP resets are generated as a result of attempted connections to unopened TCP ports. Among others, these are the kinds of activities which may cause these messages: Brute-force denial of service (DoS) attacks (as opposed to single-packet attacks which exploit a specific vulnerability). Port scans which attempt to connect to a large number of ports (as opposed to only trying a few well-known ports). The first number in the message tells you how many packets the kernel would have sent if the limit was not in place, and the second number tells you the limit. You can control the limit using the net.inet.icmp.icmplim sysctl variable like this, where 300 is the limit in packets per second: &prompt.root; sysctl -w net.inet.icmp.icmplim=300 If you do not want to see messages about this in your log files, but you still want the kernel to do response limiting, you can use the net.inet.icmp.icmplim_output sysctl variable to disable the output like this: &prompt.root; sysctl -w net.inet.icmp.icmplim_output=0 Finally, if you want to disable response limiting, you can set the net.inet.icmp.icmplim sysctl variable (see above for an example) to 0. Disabling response limiting is discouraged for the reasons listed above. What are these arp: unknown hardware address format error messages? This means that some device on your local Ethernet is using a MAC address in a format that FreeBSD does not recognize. This is probably caused by someone experimenting with an Ethernet card somewhere else on the network. You will see this most commonly on cable modem networks. It is harmless, and should not affect the performance of your FreeBSD machine. I've just installed CVSup but trying to execute it produces errors. What is wrong? First, see if the error message you are receiving is like the one shown below. /usr/libexec/ld-elf.so.1: Shared object "libXaw.so.6" not found Errors like these are caused by installing the net/cvsup port on a machine which does not have the XFree86 suite. If you want to use the GUI included with CVSup you will need to install XFree86 now. Alternatively if you just wish to use CVSup from a command line you should delete the package previously installed. Then install the net/cvsup-without-gui port. This is covered in more detail in the CVSup + url="http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/cvsup.html">CVSup section of the Handbook. Security BIND (named) is listening on port 53 and some other high-numbered port. What is going on? FreeBSD 3.0 and later use a version of BIND that uses a random high-numbered port for outgoing queries. If you want to use port 53 for outgoing queries, either to get past a firewall or to make yourself feel better, you can try the following in /etc/namedb/named.conf: options { query-source address * port 53; }; You can replace the * with a single IP address if you want to tighten things further. Congratulations, by the way. It is good practice to read your &man.sockstat.1; output and notice odd things! Sendmail is listening on port 587 as well as the standard port 25! What is going on? Recent versions of Sendmail support a mail submission feature that runs over port 587. This is not yet widely supported, but is growing in popularity. What is this UID 0 toor account? Have I been compromised? Do not worry. toor is an alternative superuser account (toor is root spelt backwards). Previously it was created when the &man.bash.1; shell was installed but now it is created by default. It is intended to be used with a non-standard shell so you do not have to change root's default shell. This is important as shells which are not part of the base distribution (for example a shell installed from ports or packages) are likely be to be installed in /usr/local/bin which, by default, resides on a different filesystem. If root's shell is located in /usr/local/bin and /usr (or whatever filesystem contains /usr/local/bin) is not mounted for some reason, root will not be able to log in to fix a problem (although if you reboot into single user mode you will be prompted for the path to a shell). Some people use toor for day-to-day root tasks with a non-standard shell, leaving root, with a standard shell, for single user mode or emergencies. By default you cannot log in using toor as it does not have a password, so log in as root and set a password for toor if you want to use it. Why is suidperl not working properly? For security reasons, suidperl is installed without the suid bit by default. The system administrator can enable suid behavior with the following command. &prompt.root; chmod u+s /usr/bin/suidperl If you want suidperl to be built suid during upgrades from source, edit /etc/make.conf and add ENABLE_SUIDPERL=true before you run make buildworld. PPP I cannot make &man.ppp.8; work. What am I doing wrong? You should first read the &man.ppp.8; man page and the PPP section of the handbook. Enable logging with the command set log Phase Chat Connect Carrier lcp ipcp ccp command This command may be typed at the &man.ppp.8; command prompt or it may be entered in the /etc/ppp/ppp.conf configuration file (the start of the default section is the best place to put it). Make sure that /etc/syslog.conf (see &man.syslog.conf.5;) contains the lines !ppp *.* /var/log/ppp.log and that the file /var/log/ppp.log exists. You can now find out a lot about what is going on from the log file. Do not worry if it does not all make sense. If you need to get help from someone, it may make sense to them. If your version of &man.ppp.8; does not understand the set log command, you should download the latest version. It will build on FreeBSD version 2.1.5 and higher. Why does &man.ppp.8; hang when I run it? This is usually because your hostname will not resolve. The best way to fix this is to make sure that /etc/hosts is consulted by your resolver first by editing /etc/host.conf and putting the hosts line first. Then, simply put an entry in /etc/hosts for your local machine. If you have no local network, change your localhost line: 127.0.0.1 foo.example.com foo localhost Otherwise, simply add another entry for your host. Consult the relevant man pages for more details. You should be able to successfully ping -c1 `hostname` when you are done. Why will &man.ppp.8; not dial in -auto mode? First, check that you have got a default route. By running netstat -rn (see &man.netstat.1;), you should see two entries like this: Destination Gateway Flags Refs Use Netif Expire default 10.0.0.2 UGSc 0 0 tun0 10.0.0.2 10.0.0.1 UH 0 0 tun0 This is assuming that you have used the addresses from the handbook, the man page or from the ppp.conf.sample file. If you do not have a default route, it may be because you are running an old version of &man.ppp.8; that does not understand the word HISADDR in the ppp.conf file. If your version of &man.ppp.8; is from before FreeBSD 2.2.5, change the add 0 0 HISADDR line to one saying add 0 0 10.0.0.2 Another reason for the default route line being missing is that you have mistakenly set up a default router in your /etc/rc.conf (see &man.rc.conf.5;) file (this file was called /etc/sysconfig prior to release 2.2.2), and you have omitted the line saying delete ALL from ppp.conf. If this is the case, go back to the Final system configuration section of the handbook. What does No route to host mean? This error is usually due to a missing MYADDR: delete ALL add 0 0 HISADDR section in your /etc/ppp/ppp.linkup file. This is only necessary if you have a dynamic IP address or do not know the address of your gateway. If you are using interactive mode, you can type the following after entering packet mode (packet mode is indicated by the capitalized PPP in the prompt): delete ALL add 0 0 HISADDR Refer to the PPP and Dynamic IP addresses section of the handbook for further details. Why does my connection drop after about 3 minutes? The default PPP timeout is 3 minutes. This can be adjusted with the line set timeout NNN where NNN is the number of seconds of inactivity before the connection is closed. If NNN is zero, the connection is never closed due to a timeout. It is possible to put this command in the ppp.conf file, or to type it at the prompt in interactive mode. It is also possible to adjust it on the fly while the line is active by connecting to ppp's server socket using &man.telnet.1; or &man.pppctl.8;. Refer to the &man.ppp.8; man page for further details. Why does my connection drop under heavy load? If you have Link Quality Reporting (LQR) configured, it is possible that too many LQR packets are lost between your machine and the peer. Ppp deduces that the line must therefore be bad, and disconnects. Prior to FreeBSD version 2.2.5, LQR was enabled by default. It is now disabled by default. LQR can be disabled with the line disable lqr Why does my connection drop after a random amount of time? Sometimes, on a noisy phone line or even on a line with call waiting enabled, your modem may hang up because it thinks (incorrectly) that it lost carrier. There is a setting on most modems for determining how tolerant it should be to temporary losses of carrier. On a USR Sportster for example, this is measured by the S10 register in tenths of a second. To make your modem more forgiving, you could add the following send-expect sequence to your dial string: set dial "...... ATS10=10 OK ......" Refer to your modem manual for details. Why does my connection hang after a random amount of time? Many people experience hung connections with no apparent explanation. The first thing to establish is which side of the link is hung. If you are using an external modem, you can simply try using &man.ping.8; to see if the TD light is flashing when you transmit data. If it flashes (and the RD light does not), the problem is with the remote end. If TD does not flash, the problem is local. With an internal modem, you will need to use the set server command in your ppp.conf file. When the hang occurs, connect to &man.ppp.8; using &man.pppctl.8;. If your network connection suddenly revives (PPP was revived due to the activity on the diagnostic socket) or if you cannot connect (assuming the set socket command succeeded at startup time), the problem is local. If you can connect and things are still hung, enable local async logging with set log local async and use &man.ping.8; from another window or terminal to make use of the link. The async logging will show you the data being transmitted and received on the link. If data is going out and not coming back, the problem is remote. Having established whether the problem is local or remote, you now have two possibilities: If the problem is remote, read on entry . If the problem is local, read on entry . The remote end is not responding. What can I do? There is very little you can do about this. Most ISPs will refuse to help if you are not running a Microsoft OS. You can enable lqr in your ppp.conf file, allowing &man.ppp.8; to detect the remote failure and hang up, but this detection is relatively slow and therefore not that useful. You may want to avoid telling your ISP that you are running user-PPP... First, try disabling all local compression by adding the following to your configuration: disable pred1 deflate deflate24 protocomp acfcomp shortseq vj deny pred1 deflate deflate24 protocomp acfcomp shortseq vj Then reconnect to ensure that this makes no difference. If things improve or if the problem is solved completely, determine which setting makes the difference through trial and error. This will provide good ammunition when you contact your ISP (although it may make it apparent that you are not running a Microsoft product). Before contacting your ISP, enable async logging locally and wait until the connection hangs again. This may use up quite a bit of disk space. The last data read from the port may be of interest. It is usually ascii data, and may even describe the problem (Memory fault, core dumped?). If your ISP is helpful, they should be able to enable logging on their end, then when the next link drop occurs, they may be able to tell you why their side is having a problem. Feel free to send the details to &a.brian;, or even to ask your ISP to contact me directly. &man.ppp.8; has hung. What can I do? Your best bet here is to rebuild &man.ppp.8; by adding CFLAGS+=-g and STRIP= to the end of the Makefile, then doing a make clean && make && make install. When &man.ppp.8; hangs, find the &man.ppp.8; process id with ps ajxww | fgrep ppp and run gdb ppp PID. From the gdb prompt, you can then use bt to get a stack trace. Send the results to brian@Awfulhak.org. Why does nothing happen after the Login OK! message? Prior to FreeBSD version 2.2.5, once the link was established, &man.ppp.8; would wait for the peer to initiate the Line Control Protocol (LCP). Many ISPs will not initiate negotiations and expect the client to do so. To force &man.ppp.8; to initiate the LCP, use the following line: set openmode active It usually does no harm if both sides initiate negotiation, so openmode is now active by default. However, the next section explains when it does do some harm. I keep seeing errors about magic being the same. What does it mean? Occasionally, just after connecting, you may see messages in the log that say magic is the same. Sometimes, these messages are harmless, and sometimes one side or the other exits. Most PPP implementations cannot survive this problem, and even if the link seems to come up, you will see repeated configure requests and configure acknowledgments in the log file until &man.ppp.8; eventually gives up and closes the connection. This normally happens on server machines with slow disks that are spawning a getty on the port, and executing &man.ppp.8; from a login script or program after login. I have also heard reports of it happening consistently when using slirp. The reason is that in the time taken between &man.getty.8; exiting and &man.ppp.8; starting, the client-side &man.ppp.8; starts sending Line Control Protocol (LCP) packets. Because ECHO is still switched on for the port on the server, the client &man.ppp.8; sees these packets reflect back. One part of the LCP negotiation is to establish a magic number for each side of the link so that reflections can be detected. The protocol says that when the peer tries to negotiate the same magic number, a NAK should be sent and a new magic number should be chosen. During the period that the server port has ECHO turned on, the client &man.ppp.8; sends LCP packets, sees the same magic in the reflected packet and NAKs it. It also sees the NAK reflect (which also means &man.ppp.8; must change its magic). This produces a potentially enormous number of magic number changes, all of which are happily piling into the server's tty buffer. As soon as &man.ppp.8; starts on the server, it is flooded with magic number changes and almost immediately decides it has tried enough to negotiate LCP and gives up. Meanwhile, the client, who no longer sees the reflections, becomes happy just in time to see a hangup from the server. This can be avoided by allowing the peer to start negotiating with the following line in your ppp.conf file: set openmode passive This tells &man.ppp.8; to wait for the server to initiate LCP negotiations. Some servers however may never initiate negotiations. If this is the case, you can do something like: set openmode active 3 This tells &man.ppp.8; to be passive for 3 seconds, and then to start sending LCP requests. If the peer starts sending requests during this period, &man.ppp.8; will immediately respond rather than waiting for the full 3 second period. LCP negotiations continue until the connection is closed. What is wrong? There is currently an implementation mis-feature in &man.ppp.8; where it does not associate LCP, CCP & IPCP responses with their original requests. As a result, if one PPP implementation is more than 6 seconds slower than the other side, the other side will send two additional LCP configuration requests. This is fatal. Consider two implementations, A and B. A starts sending LCP requests immediately after connecting and B takes 7 seconds to start. When B starts, A has sent 3 LCP REQs. We are assuming the line has ECHO switched off, otherwise we would see magic number problems as described in the previous section. B sends a REQ, then an ACK to the first of A's REQs. This results in A entering the OPENED state and sending and ACK (the first) back to B. In the meantime, B sends back two more ACKs in response to the two additional REQs sent by A before B started up. B then receives the first ACK from A and enters the OPENED state. A receives the second ACK from B and goes back to the REQ-SENT state, sending another (forth) REQ as per the RFC. It then receives the third ACK and enters the OPENED state. In the meantime, B receives the forth REQ from A, resulting in it reverting to the ACK-SENT state and sending another (second) REQ and (forth) ACK as per the RFC. A gets the REQ, goes into REQ-SENT and sends another REQ. It immediately receives the following ACK and enters OPENED. This goes on until one side figures out that they are getting nowhere and gives up. The best way to avoid this is to configure one side to be passive - that is, make one side wait for the other to start negotiating. This can be done with the set openmode passive command. Care should be taken with this option. You should also use the set stopped N command to limit the amount of time that &man.ppp.8; waits for the peer to begin negotiations. Alternatively, the set openmode active N command (where N is the number of seconds to wait before starting negotiations) can be used. Check the manual page for details. Why does &man.ppp.8; lock up shortly after connection? Prior to version 2.2.5 of FreeBSD, it was possible that your link was disabled shortly after connection due to &man.ppp.8; mis-handling Predictor1 compression negotiation. This would only happen if both sides tried to negotiate different Compression Control Protocols (CCP). This problem is now corrected, but if you are still running an old version of &man.ppp.8; the problem can be circumvented with the line disable pred1 Why does &man.ppp.8; lock up when I shell out to test it? When you execute the shell or ! command, &man.ppp.8; executes a shell (or if you have passed any arguments, &man.ppp.8; will execute those arguments). Ppp will wait for the command to complete before continuing. If you attempt to use the PPP link while running the command, the link will appear to have frozen. This is because &man.ppp.8; is waiting for the command to complete. If you wish to execute commands like this, use the !bg command instead. This will execute the given command in the background, and &man.ppp.8; can continue to service the link. Why does &man.ppp.8; over a null-modem cable never exit? There is no way for &man.ppp.8; to automatically determine that a direct connection has been dropped. This is due to the lines that are used in a null-modem serial cable. When using this sort of connection, LQR should always be enabled with the line enable lqr LQR is accepted by default if negotiated by the peer. Why does &man.ppp.8; dial for no reason in -auto mode? If &man.ppp.8; is dialing unexpectedly, you must determine the cause, and set up Dial filters (dfilters) to prevent such dialing. To determine the cause, use the following line: set log +tcp/ip This will log all traffic through the connection. The next time the line comes up unexpectedly, you will see the reason logged with a convenient timestamp next to it. You can now disable dialing under these circumstances. Usually, this sort of problem arises due to DNS lookups. To prevent DNS lookups from establishing a connection (this will not prevent &man.ppp.8; from passing the packets through an established connection), use the following: set dfilter 1 deny udp src eq 53 set dfilter 2 deny udp dst eq 53 set dfilter 3 permit 0/0 0/0 This is not always suitable, as it will effectively break your demand-dial capabilities - most programs will need a DNS lookup before doing any other network related things. In the DNS case, you should try to determine what is actually trying to resolve a host name. A lot of the time, &man.sendmail.8; is the culprit. You should make sure that you tell sendmail not to do any DNS lookups in its configuration file. See the section on Mail Configuration for details on how to create your own configuration file and what should go into it. You may also want to add the following line to your .mc file: define(`confDELIVERY_MODE', `d')dnl This will make sendmail queue everything until the queue is run (usually, sendmail is invoked with , telling it to run the queue every 30 minutes) or until a sendmail -q is done (perhaps from your ppp.linkup file). What do these CCP errors mean? I keep seeing the following errors in my log file: CCP: CcpSendConfigReq CCP: Received Terminate Ack (1) state = Req-Sent (6) This is because &man.ppp.8; is trying to negotiate Predictor1 compression, and the peer does not want to negotiate any compression at all. The messages are harmless, but if you wish to remove them, you can disable Predictor1 compression locally too: disable pred1 Why does &man.ppp.8; lock up during file transfers with IO errors? Under FreeBSD 2.2.2 and before, there was a bug in the tun driver that prevents incoming packets of a size larger than the tun interface's MTU size. Receipt of a packet greater than the MTU size results in an IO error being logged via syslogd. The PPP specification says that an MTU of 1500 should always be accepted as a minimum, despite any LCP negotiations, therefore it is possible that should you decrease the MTU to less than 1500, your ISP will transmit packets of 1500 regardless, and you will tickle this non-feature - locking up your link. The problem can be circumvented by never setting an MTU of less than 1500 under FreeBSD 2.2.2 or before. Why does &man.ppp.8; not log my connection speed? In order to log all lines of your modem conversation, you must enable the following: set log +connect This will make &man.ppp.8; log everything up until the last requested expect string. If you wish to see your connect speed and are using PAP or CHAP (and therefore do not have anything to chat after the CONNECT in the dial script - no set login script), you must make sure that you instruct &man.ppp.8; to expect the whole CONNECT line, something like this: set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 4 \ \"\" ATZ OK-ATZ-OK ATDT\\T TIMEOUT 60 CONNECT \\c \\n" Here, we get our CONNECT, send nothing, then expect a line-feed, forcing &man.ppp.8; to read the whole CONNECT response. Why does &man.ppp.8; ignore the \ character in my chat script? Ppp parses each line in your config files so that it can interpret strings such as set phone "123 456 789" correctly and realize that the number is actually only one argument. In order to specify a " character, you must escape it using a backslash (\). When the chat interpreter parses each argument, it re-interprets the argument in order to find any special escape sequences such as \P or \T (see the man page). As a result of this double-parsing, you must remember to use the correct number of escapes. If you wish to actually send a \ character to (say) your modem, you would need something like: set dial "\"\" ATZ OK-ATZ-OK AT\\\\X OK" resulting in the following sequence: ATZ OK AT\X OK or set phone 1234567 set dial "\"\" ATZ OK ATDT\\T" resulting in the following sequence: ATZ OK ATDT1234567 Why does &man.ppp.8; get a seg-fault, but I see no ppp.core file? Ppp (or any other program for that matter) should never dump core. Because &man.ppp.8; runs with an effective user id of 0, the operating system will not write &man.ppp.8;'s core image to disk before terminating it. If, however &man.ppp.8; is actually terminating due to a segmentation violation or some other signal that normally causes core to be dumped, and you are sure you are using the latest version (see the start of this section), then you should do the following: &prompt.user; tar xfz ppp-*.src.tar.gz &prompt.user; cd ppp*/ppp &prompt.user; echo STRIP= >>Makefile &prompt.user; echo CFLAGS+=-g >>Makefile &prompt.user; make clean all &prompt.user; su &prompt.root; make install &prompt.root; chmod 555 /usr/sbin/ppp You will now have a debuggable version of &man.ppp.8; installed. You will have to be root to run &man.ppp.8; as all of its privileges have been revoked. When you start &man.ppp.8;, take a careful note of what your current directory was at the time. Now, if and when &man.ppp.8; receives the segmentation violation, it will dump a core file called ppp.core. You should then do the following: &prompt.user; su &prompt.root; gdb /usr/sbin/ppp ppp.core (gdb) bt ..... (gdb) f 0 .... (gdb) i args .... (gdb) l ..... All of this information should be given alongside your question, making it possible to diagnose the problem. If you are familiar with gdb, you may wish to find out some other bits and pieces such as what actually caused the dump and the addresses & values of the relevant variables. Why does the process that forces a dial in auto mode never connect? This was a known problem with &man.ppp.8; set up to negotiate a dynamic local IP number with the peer in auto mode. It is fixed in the latest version - search the man page for iface. The problem was that when that initial program calls &man.connect.2;, the IP number of the tun interface is assigned to the socket endpoint. The kernel creates the first outgoing packet and writes it to the tun device. &man.ppp.8; then reads the packet and establishes a connection. If, as a result of &man.ppp.8;'s dynamic IP assignment, the interface address is changed, the original socket endpoint will be invalid. Any subsequent packets sent to the peer will usually be dropped. Even if they are not, any responses will not route back to the originating machine as the IP number is no longer owned by that machine. There are several theoretical ways to approach this problem. It would be nicest if the peer would re-assign the same IP number if possible :-) The current version of &man.ppp.8; does this, but most other implementations do not. The easiest method from our side would be to never change the tun interface IP number, but instead to change all outgoing packets so that the source IP number is changed from the interface IP to the negotiated IP on the fly. This is essentially what the iface-alias option in the latest version of &man.ppp.8; is doing (with the help of &man.libalias.3; and &man.ppp.8;'s switch) - it is maintaining all previous interface addresses and NATing them to the last negotiated address. Another alternative (and probably the most reliable) would be to implement a system call that changes all bound sockets from one IP to another. &man.ppp.8; would use this call to modify the sockets of all existing programs when a new IP number is negotiated. The same system call could be used by dhcp clients when they are forced to re-bind() their sockets. Yet another possibility is to allow an interface to be brought up without an IP number. Outgoing packets would be given an IP number of 255.255.255.255 up until the first SIOCAIFADDR ioctl is done. This would result in fully binding the socket. It would be up to &man.ppp.8; to change the source IP number, but only if it is set to 255.255.255.255, and only the IP number and IP checksum would need to change. This, however is a bit of a hack as the kernel would be sending bad packets to an improperly configured interface, on the assumption that some other mechanism is capable of fixing things retrospectively. Why do most games not work with the -nat switch? The reason games and the like do not work when libalias is in use is that the machine on the outside will try to open a connection or send (unsolicited) UDP packets to the machine on the inside. The NAT software does not know that it should send these packets to the interior machine. To make things work, make sure that the only thing running is the software that you are having problems with, then either run tcpdump on the tun interface of the gateway or enable &man.ppp.8; tcp/ip logging (set log +tcp/ip) on the gateway. When you start the offending software, you should see packets passing through the gateway machine. When something comes back from the outside, it will be dropped (that is the problem). Note the port number of these packets then shut down the offending software. Do this a few times to see if the port numbers are consistent. If they are, then the following line in the relevant section of /etc/ppp/ppp.conf will make the software functional: nat port proto internalmachine:port port where proto is either tcp or udp, internalmachine is the machine that you want the packets to be sent to and port is the destination port number of the packets. You will not be able to use the software on other machines without changing the above command, and running the software on two internal machines at the same time is out of the question - after all, the outside world is seeing your entire internal network as being just a single machine. If the port numbers are not consistent, there are three more options: Submit support in libalias. Examples of special cases can be found in /usr/src/lib/libalias/alias_*.c (alias_ftp.c is a good prototype). This usually involves reading certain recognised outgoing packets, identifying the instruction that tells the outside machine to initiate a connection back to the internal machine on a specific (random) port and setting up a route in the alias table so that the subsequent packets know where to go. This is the most difficult solution, but it is the best and will make the software work with multiple machines. Use a proxy. The application may support socks5 for example, or (as in the cvsup case) may have a passive option that avoids ever requesting that the peer open connections back to the local machine. Redirect everything to the internal machine using nat addr. This is the sledge-hammer approach. Has anybody made a list of useful port numbers? Not yet, but this is intended to grow into such a list (if any interest is shown). In each example, internal should be replaced with the IP number of the machine playing the game. Asheron's Call nat port udp internal :65000 65000 Manually change the port number within the game to 65000. If you have got a number of machines that you wish to play on assign a unique port number for each (i.e. 65001, 65002, etc) and add a nat port line for each one. Half Life nat port udp internal:27005 27015 PCAnywhere 8.0 nat port udp internal:5632 5632 nat port tcp internal:5631 5631 Quake nat port udp internal:6112 6112 Alternatively, you may want to take a look at www.battle.net for Quake proxy support. Quake 2 nat port udp internal:27901 27910 nat port udp internal:60021 60021 nat port udp internal:60040 60040 Red Alert nat port udp internal:8675 8675 nat port udp internal:5009 5009 What are FCS errors? FCS stands for Frame Check Sequence. Each PPP packet has a checksum attached to ensure that the data being received is the data being sent. If the FCS of an incoming packet is incorrect, the packet is dropped and the HDLC FCS count is increased. The HDLC error values can be displayed using the show hdlc command. If your link is bad (or if your serial driver is dropping packets), you will see the occasional FCS error. This is not usually worth worrying about although it does slow down the compression protocols substantially. If you have an external modem, make sure your cable is properly shielded from interference - this may eradicate the problem. If your link freezes as soon as you have connected and you see a large number of FCS errors, this may be because your link is not 8 bit clean. Make sure your modem is not using software flow control (XON/XOFF). If your datalink must use software flow control, use the command set accmap 0x000a0000 to tell &man.ppp.8; to escape the ^Q and ^S characters. Another reason for seeing too many FCS errors may be that the remote end has stopped talking PPP. You may want to enable async logging at this point to determine if the incoming data is actually a login or shell prompt. If you have a shell prompt at the remote end, it is possible to terminate &man.ppp.8; without dropping the line by using the close lcp command (a following term command will reconnect you to the shell on the remote machine. If nothing in your log file indicates why the link might have been terminated, you should ask the remote administrator (your ISP?) why the session was terminated. Why do MacOS and Windows 98 connections freeze when running PPPoE on the gateway? Thanks to Michael Wozniak mwozniak@netcom.ca for figuring this out and Dan Flemming danflemming@mac.com for the Mac solution: This is due to what is called a Black Hole router. MacOS and Windows 98 (and maybe other Microsoft OSs) send TCP packets with a requested segment size too big to fit into a PPPoE frame (MTU is 1500 by default for Ethernet) and have the do not fragment bit set (default of TCP) and the Telco router is not sending ICMP must fragment back to the www site you are trying to load. (Alternatively, the router is sending the ICMP packet correctly, but the firewall at the www site is dropping it.) When the www server is sending you frames that do not fit into the PPPoE pipe the Telco router drops them on the floor and your page does not load (some pages/graphics do as they are smaller than a MSS.) This seems to be the default of most Telco PPPoE configurations (if only they knew how to program a router... sigh...) One fix is to use regedit on your 95/98 boxes to add the following registry entry... HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Class\NetTrans\0000\MaxMTU It should be a string with a value 1436, as some ADSL routers are reported to be unable to deal with packets larger than this. This registry key has been changed to Tcpip\Parameters\Interfaces\ID for adapter\MTU in Windows 2000 and becomes a DWORD. Refer to the Microsoft Knowledge Base documents Q158474 - Windows TCPIP Registry Entries and Q120642 - TCPIP & NBT Configuration Parameters for Windows NT for more information on changing Windows MTU to work with a NAT router. Another regedit possibility under Windows 2000 is to set the Tcpip\Parameters\Interfaces\ID for adapter\EnablePMTUBHDetect DWORD to 1 as mentioned in the Microsoft document 120642 mentioned above. Unfortunately, MacOS does not provide an interface for changing TCP/IP settings. However, there is commercial software available, such as OTAdvancedTuner (OT for OpenTransport, the MacOS TCP/IP stack) by Sustainable Softworks, that will allow users to customize TCP/IP settings. MacOS NAT users should select ip_interface_MTU from the drop-down menu, enter 1450 instead of 1500 in the box, click the box next to Save as Auto Configure, and click Make Active. The latest version of &man.ppp.8; (2.3 or greater) has an enable tcpmssfixup command that will automatically adjust the MSS to an appropriate value. This facility is enabled by default. If you are stuck with an older version of &man.ppp.8;, you may want to look at the tcpmssd port. None of this helps - I am desperate! What can I do? If all else fails, send as much information as you can, including your config files, how you are starting &man.ppp.8;, the relevant parts of your log file and the output of the netstat -rn command (before and after connecting) to the &a.questions; or the comp.unix.bsd.freebsd.misc news group, and someone should point you in the right direction. Serial Communications This section answers common questions about serial communications with FreeBSD. PPP and SLIP are covered in the section. How do I tell if FreeBSD found my serial ports? As the FreeBSD kernel boots, it will probe for the serial ports in your system for which the kernel was configured. You can either watch your system closely for the messages it prints or run the command &prompt.user; dmesg | grep sio after your system is up and running. Here is some example output from the above command: sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16550A sio1 at 0x2f8-0x2ff irq 3 on isa sio1: type 16550A This shows two serial ports. The first is on irq 4, is using port address 0x3f8, and has a 16550A-type UART chip. The second uses the same kind of chip but is on irq 3 and is at port address 0x2f8. Internal modem cards are treated just like serial ports---except that they always have a modem attached to the port. The GENERIC kernel includes support for two serial ports using the same irq and port address settings in the above example. If these settings are not right for your system, or if you have added modem cards or have more serial ports than your kernel is configured for, just reconfigure your kernel. See section about building a kernel for more details. How do I tell if FreeBSD found my modem cards? Refer to the answer to the previous question. I just upgraded to 2.0.5 and my tty0X are missing! How do I solve this problem? Do not worry, they have been merged with the ttydX devices. You will have to change any old configuration files you have, though. How do I access the serial ports on FreeBSD? The third serial port, sio2 (see &man.sio.4;, known as COM3 in DOS), is on /dev/cuaa2 for dial-out devices, and on /dev/ttyd2 for dial-in devices. What is the difference between these two classes of devices? You use ttydX for dial-ins. When opening /dev/ttydX in blocking mode, a process will wait for the corresponding cuaaX device to become inactive, and then wait for the carrier detect line to go active. When you open the cuaaX device, it makes sure the serial port is not already in use by the ttydX device. If the port is available, it steals it from the ttydX device. Also, the cuaaX device does not care about carrier detect. With this scheme and an auto-answer modem, you can have remote users log in and you can still dial out with the same modem and the system will take care of all the conflicts. How do I enable support for a multiport serial card? Again, the section on kernel configuration provides information about configuring your kernel. For a multiport serial card, place an &man.sio.4; line for each serial port on the card in the kernel configuration file. But place the irq and vector specifiers on only one of the entries. All of the ports on the card should share one irq. For consistency, use the last serial port to specify the irq. Also, specify the COM_MULTIPORT option. The following example is for an AST 4-port serial card on irq 7: options "COM_MULTIPORT" device sio4 at isa? port 0x2a0 tty flags 0x781 device sio5 at isa? port 0x2a8 tty flags 0x781 device sio6 at isa? port 0x2b0 tty flags 0x781 device sio7 at isa? port 0x2b8 tty flags 0x781 irq 7 vector siointr The flags indicate that the master port has minor number 7 (0x700), diagnostics enabled during probe (0x080), and all the ports share an irq (0x001). Can FreeBSD handle multiport serial cards sharing irqs? Not yet. You will have to use a different irq for each card. Can I set the default serial parameters for a port? The ttydX (or cuaaX) device is the regular device you will want to open for your applications. When a process opens the device, it will have a default set of terminal I/O settings. You can see these settings with the command &prompt.root; stty -a -f /dev/ttyd1 When you change the settings to this device, the settings are in effect until the device is closed. When it is reopened, it goes back to the default set. To make changes to the default set, you can open and adjust the settings of the initial state device. For example, to turn on CLOCAL mode, 8 bits, and XON/XOFF flow control by default for ttyd5, do: &prompt.root; stty -f /dev/ttyid5 clocal cs8 ixon ixoff A good place to do this is in /etc/rc.serial. Now, an application will have these settings by default when it opens ttyd5. It can still change these settings to its liking, though. You can also prevent certain settings from being changed by an application by making adjustments to the lock state device. For example, to lock the speed of ttyd5 to 57600 bps, do &prompt.root; stty -f /dev/ttyld5 57600 Now, an application that opens ttyd5 and tries to change the speed of the port will be stuck with 57600 bps. Naturally, you should make the initial state and lock state devices writable only by root. The &man.MAKEDEV.8; script does NOT do this when it creates the device entries. How can I enable dialup logins on my modem? So you want to become an Internet service provider, eh? First, you will need one or more modems that can auto-answer. Your modem will need to assert carrier-detect when it detects a carrier and not assert it all the time. It will need to hang up the phone and reset itself when the data terminal ready (DTR) line goes from on to off. It should probably use RTS/CTS flow control or no local flow control at all. Finally, it must use a constant speed between the computer and itself, but (to be nice to your callers) it should negotiate a speed between itself and the remote modem. For many Hayes command-set--compatible modems, this command will make these settings and store them in nonvolatile memory: AT &C1 &D3 &K3 &Q6 S0=1 &W See the section on sending AT commands below for information on how to make these settings without resorting to an MS-DOS terminal program. Next, make an entry in /etc/ttys (see &man.ttys.5;) for the modem. This file lists all the ports on which the operating system will await logins. Add a line that looks something like this: ttyd1 "/usr/libexec/getty std.57600" dialup on insecure This line indicates that the second serial port (/dev/ttyd1) has a modem connected running at 57600 bps and no parity (std.57600, which comes from the file /etc/gettytab, see &man.gettytab.5;). The terminal type for this port is dialup. The port is on and is insecure---meaning root logins on the port are not allowed. For dialin ports like this one, use the ttydX entry. It is common practice to use dialup as the terminal type. Many users set up in their .profile or .login files a prompt for the actual terminal type if the starting type is dialup. The example shows the port as insecure. To become root on this port, you have to login as a regular user, then &man.su.1; to become root. If you use secure then root can login in directly. After making modifications to /etc/ttys, you need to send a hangup or HUP signal to the &man.init.8; process: &prompt.root; kill -HUP 1 This forces the &man.init.8; process to reread /etc/ttys. The init process will then start getty processes on all on ports. You can find out if logins are available for your port by typing &prompt.user; ps -ax | grep '[t]tyd1' You should see something like: 747 ?? I 0:00.04 /usr/libexec/getty std.57600 ttyd1 How can I connect a dumb terminal to my FreeBSD box? If you are using another computer as a terminal into your FreeBSD system, get a null modem cable to go between the two serial ports. If you are using an actual terminal, see its accompanying instructions. Then, modify /etc/ttys (see &man.ttys.5;), like above. For example, if you are hooking up a WYSE-50 terminal to the fifth serial port, use an entry like this: ttyd4 "/usr/libexec/getty std.38400" wyse50 on secure This example shows that the port on /dev/ttyd4 has a wyse50 terminal connected at 38400 bps with no parity (std.38400 from /etc/gettytab, see &man.gettytab.5;) and root logins are allowed (secure). Why can I not run tip or cu? On your system, the programs &man.tip.1; and &man.cu.1; are probably executable only by uucp and group dialer. You can use the group dialer to control who has access to your modem or remote systems. Just add yourself to group dialer. Alternatively, you can let everyone on your system run &man.tip.1; and &man.cu.1; by typing: &prompt.root; chmod 4511 /usr/bin/cu &prompt.root; chmod 4511 /usr/bin/tip My stock Hayes modem is not supported---what can I do? Actually, the man page for &man.tip.1; is out of date. There is a generic Hayes dialer already built in. Just use at=hayes in your /etc/remote (see &man.remote.5;) file. The Hayes driver is not smart enough to recognize some of the advanced features of newer modems---messages like BUSY, NO DIALTONE, or CONNECT 115200 will just confuse it. You should turn those messages off when you use &man.tip.1; (using ATX0&W). Also, the dial timeout for &man.tip.1; is 60 seconds. Your modem should use something less, or else tip will think there is a communication problem. Try ATS7=45&W. Actually, as shipped &man.tip.1; does not yet support it fully. The solution is to edit the file tipconf.h in the directory /usr/src/usr.bin/tip/tip. Obviously you need the source distribution to do this. Edit the line #define HAYES 0 to #define HAYES 1. Then make and make install. Everything works nicely after that. How am I expected to enter these AT commands? Make what is called a direct entry in your /etc/remote file (see &man.remote.5;). For example, if your modem is hooked up to the first serial port, /dev/cuaa0, then put in the following line: cuaa0:dv=/dev/cuaa0:br#19200:pa=none Use the highest bps rate your modem supports in the br capability. Then, type tip cuaa0 (see &man.tip.1;) and you will be connected to your modem. If there is no /dev/cuaa0 on your system, do this: &prompt.root; cd /dev &prompt.root; sh MAKEDEV cuaa0 Or use cu as root with the following command: &prompt.root; cu -lline -sspeed with line being the serial port (e.g. /dev/cuaa0) and speed being the speed (e.g.57600). When you are done entering the AT commands hit ~. to exit. Why does the <@> sign for the pn capability not work? The <@> sign in the phone number capability tells tip to look in /etc/phones for a phone number. But the <@> sign is also a special character in capability files like /etc/remote. Escape it with a backslash: pn=\@ How can I dial a phone number on the command line? Put what is called a generic entry in your /etc/remote file (see &man.remote.5;). For example: tip115200|Dial any phone number at 115200 bps:\ :dv=/dev/cuaa0:br#115200:at=hayes:pa=none:du: tip57600|Dial any phone number at 57600 bps:\ :dv=/dev/cuaa0:br#57600:at=hayes:pa=none:du: Then you can do something like tip -115200 5551234. If you prefer &man.cu.1; over &man.tip.1;, use a generic cu entry: cu115200|Use cu to dial any number at 115200bps:\ :dv=/dev/cuaa1:br#57600:at=hayes:pa=none:du: and type cu 5551234 -s 115200. Do I have to type in the bps rate every time I do that? Put in an entry for tip1200 or cu1200, but go ahead and use whatever bps rate is appropriate with the br capability. &man.tip.1; thinks a good default is 1200 bps which is why it looks for a tip1200 entry. You do not have to use 1200 bps, though. How can I more easily access a number of hosts through a terminal server? Rather than waiting until you are connected and typing CONNECT host each time, use tip's cm capability. For example, these entries in /etc/remote (see &man.remote.5;): pain|pain.deep13.com|Forrester's machine:\ :cm=CONNECT pain\n:tc=deep13: muffin|muffin.deep13.com|Frank's machine:\ :cm=CONNECT muffin\n:tc=deep13: deep13:Gizmonics Institute terminal server:\ :dv=/dev/cuaa2:br#38400:at=hayes:du:pa=none:pn=5551234: will let you type tip pain or tip muffin to connect to the hosts pain or muffin; and tip deep13 to get to the terminal server. Can tip try more than one line for each site? This is often a problem where a university has several modem lines and several thousand students trying to use them... Make an entry for your university in /etc/remote (see &man.remote.5;) and use <\@> for the pn capability: big-university:\ :pn=\@:tc=dialout dialout:\ :dv=/dev/cuaa3:br#9600:at=courier:du:pa=none: Then, list the phone numbers for the university in /etc/phones (see &man.phones.5;): big-university 5551111 big-university 5551112 big-university 5551113 big-university 5551114 &man.tip.1; will try each one in the listed order, then give up. If you want to keep retrying, run &man.tip.1; in a while loop. Why do I have to hit CTRLP twice to send CTRLP once? CTRLP is the default force character, used to tell &man.tip.1; that the next character is literal data. You can set the force character to any other character with the ~s escape, which means set a variable. Type ~sforce=single-char followed by a newline. single-char is any single character. If you leave out single-char, then the force character is the nul character, which you can get by typing CTRL2 or CTRLSPACE. A pretty good value for single-char is SHIFTCTRL6, which I have seen only used on some terminal servers. You can have the force character be whatever you want by specifying the following in your $HOME/.tiprc file: force=single-char Why is everything I type suddenly in UPPER CASE? You must have pressed CTRLA, &man.tip.1; raise character, specially designed for people with broken Caps Lock keys. Use ~s as above and set the variable raisechar to something reasonable. In fact, you can set it to the same as the force character, if you never expect to use either of these features. Here is a sample .tiprc file perfect for Emacs users who need to type CTRL2 and CTRLA a lot: force=^^ raisechar=^^ The ^^ is SHIFTCTRL6. How can I do file transfers with tip? If you are talking to another Unix system, you can send and receive files with ~p (put) and ~t (take). These commands run &man.cat.1; and &man.echo.1; on the remote system to accept and send files. The syntax is: ~p <local-file> [<remote-file>] ~t <remote-file> [<local-file>] There is no error checking, so you probably should use another protocol, like zmodem. How can I run zmodem with tip? First, install one of the zmodem programs from the ports collection (such as one of the two from the comms category, lrzsz or rzsz. To receive files, start the sending program on the remote end. Then, press enter and type ~C rz (or ~C lrz if you installed lrzsz) to begin receiving them locally. To send files, start the receiving program on the remote end. Then, press enter and type ~C sz files (or ~C lsz files) to send them to the remote system. Why does FreeBSD not find my serial ports, even when the settings are correct? Motherboards and cards with Acer UARTs do not probe properly under the FreeBSD sio probe. Obtain a patch from www.lemis.com to fix your problem. Miscellaneous Questions FreeBSD uses far more swap space than Linux. Why? FreeBSD only appears to use more swap than Linux. In actual fact, it does not. The main difference between FreeBSD and Linux in this regard is that FreeBSD will proactively move entirely idle, unused pages of main memory into swap in order to make more main memory available for active use. Linux tends to only move pages to swap as a last resort. The perceived heavier use of swap is balanced by the more efficient use of main memory. Note that while FreeBSD is proactive in this regard, it does not arbitrarily decide to swap pages when the system is truly idle. Thus you will not find your system all paged out when you get up in the morning after leaving it idle overnight. Why does top show very little free memory even when I have very few programs running? The simple answer is that free memory is wasted memory. Any memory that your programs do not actively allocate is used within the FreeBSD kernel as disk cache. The values shown by &man.top.1; labeled as Inact, Cache, and Buf are all cached data at different aging levels. This cached data means the system does not have to access a slow disk again for data it has accessed recently, thus increasing overall performance. In general, a low value shown for Free memory in &man.top.1; is good, provided it is not very low. Why use (what are) a.out and ELF executable formats? To understand why FreeBSD uses the ELF format, you must first know a little about the 3 currently dominant executable formats for Unix: Prior to FreeBSD 3.x, FreeBSD used the a.out format. &man.a.out.5; The oldest and classic Unix object format. It uses a short and compact header with a magic number at the beginning that is often used to characterize the format (see &man.a.out.5; for more details). It contains three loaded segments: .text, .data, and .bss plus a symbol table and a string table. COFF The SVR3 object format. The header now comprises a section table, so you can have more than just .text, .data, and .bss sections. ELF The successor to COFF, featuring Multiple sections and 32-bit or 64-bit possible values. One major drawback: ELF was also designed with the assumption that there would be only one ABI per system architecture. That assumption is actually quite incorrect, and not even in the commercial SYSV world (which has at least three ABIs: SVR4, Solaris, SCO) does it hold true. FreeBSD tries to work around this problem somewhat by providing a utility for branding a known ELF executable with information about the ABI it is compliant with. See the man page for &man.brandelf.1; for more information. FreeBSD comes from the classic camp and has traditionally used the &man.a.out.5; format, a technology tried and proven through many generations of BSD releases. Though it has also been possible for some time to build and run native ELF binaries (and kernels) on a FreeBSD system, FreeBSD initially resisted the push to switch to ELF as the default format. Why? Well, when the Linux camp made their painful transition to ELF, it was not so much to flee the a.out executable format as it was their inflexible jump-table based shared library mechanism, which made the construction of shared libraries very difficult for vendors and developers alike. Since the ELF tools available offered a solution to the shared library problem and were generally seen as the way forward anyway, the migration cost was accepted as necessary and the transition made. In FreeBSD's case, our shared library mechanism is based more closely on Sun's SunOS-style shared library mechanism and, as such, is very easy to use. However, starting with 3.0, FreeBSD officially supports ELF binaries as the default format. Even though the a.out executable format has served us well, the GNU people, who author the compiler tools we use, have dropped support for the a.out format. This has forced us to maintain a divergent version of the compiler and linker, and has kept us from reaping the benefits of the latest GNU development efforts. Also the demands of ISO-C++, notably constructors and destructors, has also led to native ELF support in future FreeBSD releases. Yes, but why are there so many different formats? Back in the dim, dark past, there was simple hardware. This simple hardware supported a simple, small system. a.out was completely adequate for the job of representing binaries on this simple system (a PDP-11). As people ported Unix from this simple system, they retained the a.out format because it was sufficient for the early ports of Unix to architectures like the Motorola 68k, VAXen, etc. Then some bright hardware engineer decided that if he could force software to do some sleazy tricks, then he would be able to shave a few gates off the design and allow his CPU core to run faster. While it was made to work with this new kind of hardware (known these days as RISC), a.out was ill-suited for this hardware, so many formats were developed to get to a better performance from this hardware than the limited, simple a.out format could offer. Things like COFF, ECOFF, and a few obscure others were invented and their limitations explored before things seemed to settle on ELF. In addition, program sizes were getting huge and disks (and physical memory) were still relatively small so the concept of a shared library was born. The VM system also became more sophisticated. While each one of these advancements was done using the a.out format, its usefulness was stretched more and more with each new feature. In addition, people wanted to dynamically load things at run time, or to junk parts of their program after the init code had run to save in core memory and/or swap space. Languages became more sophisticated and people wanted code called before main automatically. Lots of hacks were done to the a.out format to allow all of these things to happen, and they basically worked for a time. In time, a.out was not up to handling all these problems without an ever increasing overhead in code and complexity. While ELF solved many of these problems, it would be painful to switch from the system that basically worked. So ELF had to wait until it was more painful to remain with a.out than it was to migrate to ELF. However, as time passed, the build tools that FreeBSD derived their build tools from (the assembler and loader especially) evolved in two parallel trees. The FreeBSD tree added shared libraries and fixed some bugs. The GNU folks that originally write these programs rewrote them and added simpler support for building cross compilers, plugging in different formats at will, etc. Since many people wanted to build cross compilers targeting FreeBSD, they were out of luck since the older sources that FreeBSD had for as and ld were not up to the task. The new gnu tools chain (binutils) does support cross compiling, ELF, shared libraries, C++ extensions, etc. In addition, many vendors are releasing ELF binaries, and it is a good thing for FreeBSD to run them. And if it is running ELF binaries, why bother having a.out any more? It is a tired old horse that has proven useful for a long time, but it is time to turn him out to pasture for his long, faithful years of service. ELF is more expressive than a.out and will allow more extensibility in the base system. The ELF tools are better maintained, and offer cross compilation support, which is important to many people. ELF may be a little slower than a.out, but trying to measure it can be difficult. There are also numerous details that are different between the two in how they map pages, handle init code, etc. None of these are very important, but they are differences. In time support for a.out will be moved out of the GENERIC kernel, and eventually removed from the kernel once the need to run legacy a.out programs is past. Why will chmod not change the permissions on symlinks? Symlinks do not have permissions, and by default, &man.chmod.1; will not follow symlinks to change the permissions on the target file. So if you have a file, foo, and a symlink to that file, bar, then this command will always succeed. &prompt.user; chmod g-w bar However, the permissions on foo will not have changed. You have to use either or together with the option to make this work. See the &man.chmod.1; and &man.symlink.7; man pages for more info. The option does a RECURSIVE &man.chmod.1;. Be careful about specifying directories or symlinks to directories to &man.chmod.1;. If you want to change the permissions of a directory referenced by a symlink, use &man.chmod.1; without any options and follow the symlink with a trailing slash (/). For example, if foo is a symlink to directory bar, and you want to change the permissions of foo (actually bar), you would do something like: &prompt.user; chmod 555 foo/ With the trailing slash, &man.chmod.1; will follow the symlink, foo, to change the permissions of the directory, bar. Why are login names restricted to 8 characters or less in FreeBSD 2.2.X and earlier? You would think it would be easy enough to change UT_NAMESIZE and rebuild the whole world, and everything would just work. Unfortunately there are often scads of applications and utilities (including system tools) that have hard-coded small numbers (not always 8 or 9, but oddball ones like 15 and 20) in structures and buffers. Not only will this get you log files which are trashed (due to variable-length records getting written when fixed records were expected), but it can break Suns NIS clients and potentially cause other problems in interacting with other Unix systems. In FreeBSD 3.0 and later, the maximum name length has been increased to 16 characters and those various utilities with hard-coded name sizes have been found and fixed. The fact that this touched so many areas of the system is why, in fact, the change was not made until 3.0. If you are absolutely confident in your ability to find and fix these sorts of problems for yourself when and if they pop up, you can increase the login name length in earlier releases by editing /usr/include/utmp.h and changing UT_NAMESIZE accordingly. You must also update MAXLOGNAME in /usr/include/sys/param.h to match the UT_NAMESIZE change. Finally, if you build from sources, do not forget that /usr/include is updated each time! Change the appropriate files in /usr/src/.. instead. Can I run DOS binaries under FreeBSD? Yes, starting with version 3.0 you can use BSDI's doscmd DOS emulation which has been integrated and enhanced. Send mail to the &a.emulation; if you are interested in joining this ongoing effort! For pre-3.0 systems, there is a neat utility called pcemu in the ports collection which emulates an 8088 and enough BIOS services to run DOS text mode applications. It requires the X Window System (provided as XFree86). What do I need to do to translate a FreeBSD document into my native language? See the Translation FAQ in the FreeBSD Documentation Project Primer. Why does my email to any address at FreeBSD.org bounce? The FreeBSD.org mail system implements some of the stricter Postfix checks on incoming mail and rejects mail that is either misconfigured or is potential spam. Your mail might bounce for one of the following reasons: The email is being sent from a known spam domain or IP block. The FreeBSD mail servers reject email from known spam sources. If you have service through a company or domain who generates or relays spam, please switch to a service provider who does not. The body of the email only contains HTML. Mail should be sent in plain text only. Please configure your mail user agent to send plain text. The mailer at FreeBSD.org cannot resolve the IP address of the connecting host back to a symbolic name. Working reverse DNS is a standard requirement for accepting mail from a host. Set up reverse DNS for your mail server's IP address. Many home services (DSL, cable, dialup, etc.) will not give you this option. In this case, relay your email through your service provider's mail server. The hostname given in the EHLO/HELO part of the SMTP exchange cannot be resolved to an IP address. A fully qualified, resolvable host name is necessary in this part of the SMTP dialogue before mail will be accepted. If you do not have a host name that is registered in the DNS, then you should use your service provider's mail server to relay your mail. Your message had a message ID ending with the string localhost. Some mail user agents generate bad message IDs which will not be accepted. You will need to persuade your mail user agent to generate a valid message ID or else configure your mail transfer agent to rewrite them. Where can I find a free FreeBSD account? While FreeBSD does not provide open access to any of their servers, others do provide open access Unix systems. The charge varies and limited services may be available. Arbornet, Inc, also known as M-Net, has been providing open access to Unix systems since 1983. Starting on an Altos running System III, the site switched to BSD/OS in 1991. In June of 2000, the site switched again to FreeBSD. M-Net can be accessed via telnet and SSH and provides basic access to the entire FreeBSD software suite. However, network access is limited to members and patrons who donate to the system, which is run as a non-profit organization. M-Net also provides an bulletin board system and interactive chat. Grex provides a site very similar to M-Net including the same bulletin board and interactive chat software. However, the machine is a Sun 4M and is running SunOS What is sup, and how do I use it? SUP stands for Software Update Protocol, and was developed by CMU for keeping their development trees in sync. We used it to keep remote sites in sync with our central development sources. SUP is not bandwidth friendly, and has been retired. The current recommended method to keep your sources up to date is CVSup What is the cute little red guy's name? He does not have one, and is just called the BSD daemon. If you insist upon using a name, call him beastie. Note that beastie is pronounced BSD. You can learn more about the BSD daemon on his home page. Can I use the BSD daemon image? Perhaps. The BSD daemon is copyrighted by Marshall Kirk McKusick. You will want to check his Statement on the Use of the BSD Daemon Figure for detailed usage terms. In summary, you are free to use the image in a tasteful manner, for personal use, so long as appropriate credit is given. If you want to use him commercially, you must contact Kirk McKusick. More details are available on the BSD Daemon's home page. Do you have any BSD daemon images I could use? You will find eps and Xfig drawings under /usr/share/examples/BSD_daemon/. What does MFC mean? MFC is an acronym for Merged From -CURRENT. It is used in the CVS logs to denote when a change was migrated from the CURRENT to the STABLE branches. What does BSD mean? It stands for something in a secret language that only members can know. It does not translate literally but its ok to tell you that BSD's translation is something between, Formula-1 Racing Team, Penguins are tasty snacks, and We have a better sense of humor than Linux. :-) Seriously, BSD is an acronym for Berkeley Software Distribution, which is the name the Berkeley CSRG (Computer Systems Research Group) chose for their Unix distribution way back when. What does POLA mean? Principle of Least Astonishment. It means that as FreeBSD evolves, changes visible to the user should be kept as unsurprising as possible. For example, arbitrarily rearranging system startup variables in /etc/defaults/rc.conf violates POLA. Developers consider POLA when contemplating user-visible system changes. What is a repo-copy? A repo-copy (which is a short form of repository copy) refers to the direct copying of files within the CVS repository. Without a repo-copy, if a file needed to be copied or moved to another place in the repository, the committer would run cvs add to put the file in its new location, and then cvs rm on the old file if the old copy was being removed. The disadvantage of this method is that the history (i.e. the entries in the CVS logs) of the file would not be copied to the new location. As the FreeBSD Project considers this history very useful, a repository copy is often used instead. This is a process where one of the repository meisters will copy the files directly within the repository, rather than using the &man.cvs.1; program. Why should I care what color the bikeshed is? The really, really short answer is that you should not. The somewhat longer answer is that just because you are capable of building a bikeshed does not mean you should stop others from building one just because you do not like the color they plan to paint it. This is a metaphor indicating that you need not argue about every little feature just because you know enough to do so. Some people have commented that the amount of noise generated by a change is inversely proportional to the complexity of the change. The longer and more complete answer is that after a very long argument about whether &man.sleep.1; should take fractional second arguments, &a.phk; posted a long message entitled A bike shed (any colour will do) on greener grass.... The appropriate portions of that message are quoted below.
&a.phk; on freebsd-hackers, October 2, 1999 What is it about this bike shed? Some of you have asked me. It is a long story, or rather it is an old story, but it is quite short actually. C. Northcote Parkinson wrote a book in the early 1960s, called Parkinson's Law, which contains a lot of insight into the dynamics of management. [snip a bit of commentary on the book] In the specific example involving the bike shed, the other vital component is an atomic power-plant, I guess that illustrates the age of the book. Parkinson shows how you can go into the board of directors and get approval for building a multi-million or even billion dollar atomic power plant, but if you want to build a bike shed you will be tangled up in endless discussions. Parkinson explains that this is because an atomic plant is so vast, so expensive and so complicated that people cannot grasp it, and rather than try, they fall back on the assumption that somebody else checked all the details before it got this far. Richard P. Feynmann gives a couple of interesting, and very much to the point, examples relating to Los Alamos in his books. A bike shed on the other hand. Anyone can build one of those over a weekend, and still have time to watch the game on TV. So no matter how well prepared, no matter how reasonable you are with your proposal, somebody will seize the chance to show that he is doing his job, that he is paying attention, that he is here. In Denmark we call it setting your fingerprint. It is about personal pride and prestige, it is about being able to point somewhere and say There! I did that. It is a strong trait in politicians, but present in most people given the chance. Just think about footsteps in wet cement.
The FreeBSD Funnies How cool is FreeBSD? Q. Has anyone done any temperature testing while running FreeBSD? I know Linux runs cooler than DOS, but have never seen a mention of FreeBSD. It seems to run really hot. A. No, but we have done numerous taste tests on blindfolded volunteers who have also had 250 micrograms of LSD-25 administered beforehand. 35% of the volunteers said that FreeBSD tasted sort of orange, whereas Linux tasted like purple haze. Neither group mentioned any significant variances in temperature. We eventually had to throw the results of this survey out entirely anyway when we found that too many volunteers were wandering out of the room during the tests, thus skewing the results. We think most of the volunteers are at Apple now, working on their new scratch and sniff GUI. It is a funny old business we are in! Seriously, both FreeBSD and Linux use the HLT (halt) instruction when the system is idle thus lowering its energy consumption and therefore the heat it generates. Also if you have APM (advanced power management) configured, then FreeBSD can also put the CPU into a low power mode. Who is scratching in my memory banks?? Q. Is there anything odd that FreeBSD does when compiling the kernel which would cause the memory to make a scratchy sound? When compiling (and for a brief moment after recognizing the floppy drive upon startup, as well), a strange scratchy sound emanates from what appears to be the memory banks. A. Yes! You will see frequent references to daemons in the BSD documentation, and what most people do not know is that this refers to genuine, non-corporeal entities that now possess your computer. The scratchy sound coming from your memory is actually high-pitched whispering exchanged among the daemons as they best decide how to deal with various system administration tasks. If the noise gets to you, a good fdisk /mbr from DOS will get rid of them, but do not be surprised if they react adversely and try to stop you. In fact, if at any point during the exercise you hear the satanic voice of Bill Gates coming from the built-in speaker, take off running and do not ever look back! Freed from the counterbalancing influence of the BSD daemons, the twin demons of DOS and Windows are often able to re-assert total control over your machine to the eternal damnation of your soul. Now that you know, given a choice you would probably prefer to get used to the scratchy noises, no? How many FreeBSD hackers does it take to change a lightbulb? One thousand, one hundred and seventy-two: Twenty-three to complain to -CURRENT about the lights being out; Four to claim that it is a configuration problem, and that such matters really belong on -questions; Three to submit PRs about it, one of which is misfiled under doc and consists only of "it's dark"; One to commit an untested lightbulb which breaks buildworld, then back it out five minutes later; Eight to flame the PR originators for not including patches in their PRs; Five to complain about buildworld being broken; Thirty-one to answer that it works for them, and they must have cvsupped at a bad time; One to post a patch for a new lightbulb to -hackers; One to complain that he had patches for this three years ago, but when he sent them to -CURRENT they were just ignored, and he has had bad experiences with the PR system; besides, the proposed new lightbulb is non-reflexive; Thirty-seven to scream that lightbulbs do not belong in the base system, that committers have no right to do things like this without consulting the Community, and WHAT IS -CORE DOING ABOUT IT!? Two hundred to complain about the color of the bicycle shed; Three to point out that the patch breaks &man.style.9;; Seventeen to complain that the proposed new lightbulb is under GPL; Five hundred and eighty-six to engage in a flame war about the comparative advantages of the GPL, the BSD license, the MIT license, the NPL, and the personal hygiene of unnamed FSF founders; Seven to move various portions of the thread to -chat and -advocacy; One to commit the suggested lightbulb, even though it shines dimmer than the old one; Two to back it out with a furious flame of a commit message, arguing that FreeBSD is better off in the dark than with a dim lightbulb; Forty-six to argue vociferously about the backing out of the dim lightbulb and demanding a statement from -core; Eleven to request a smaller lightbulb so it will fit their Tamagotchi if we ever decide to port FreeBSD to that platform; Seventy-three to complain about the SNR on -hackers and -chat and unsubscribe in protest; Thirteen to post "unsubscribe", "How do I unsubscribe?", or "Please remove me from the list", followed by the usual footer; One to commit a working lightbulb while everybody is too busy flaming everybody else to notice; Thirty-one to point out that the new lightbulb would shine 0.364% brighter if compiled with TenDRA (although it will have to be reshaped into a cube), and that FreeBSD should therefore switch to TenDRA instead of GCC; One to complain that the new lightbulb lacks fairings; Nine (including the PR originators) to ask "what is MFC?"; Fifty-seven to complain about the lights being out two weeks after the bulb has been changed. &a.nik; adds: I was laughing quite hard at this. And then I thought, "Hang on, shouldn't there be '1 to document it.' in that list somewhere?" And then I was enlightened :-) Where does data written to /dev/null go? It goes into a special data sink in the CPU where it is converted to heat which is vented through the heatsink / fan assembly. This is why CPU cooling is increasingly important; as people get used to faster processors, they become careless with their data and more and more of it ends up in /dev/null, overheating their CPUs. If you delete /dev/null (which effectively disables the CPU data sink) your CPU may run cooler but your system will quickly become constipated with all that excess data and start to behave erratically. If you have a fast network connection you can cool down your CPU by reading data out of /dev/random and sending it off somewhere; however you run the risk of overheating your network connection and / or angering your ISP, as most of the data will end up getting converted to heat by their equipment, but they generally have good cooling, so if you do not overdo it you should be OK. Paul Robinson adds: There are other methods. As every good sysadmin knows, it is part of standard practise to send data to the screen of interesting variety to keep all the pixies that make up your picture happy. Screen pixies (commonly mis-typed or re-named as 'pixels') are categorised by the type of hat they wear (red, green or blue) and will hide or appear (thereby showing the colour of their hat) whenever they receive a little piece of food. Video cards turn data into pixie-food, and then send them to the pixies - the more expensive the card, the better the food, so the better behaved the pixies are. They also need constant simulation - this is why screen savers exist. To take your suggestions further, you could just throw the random data to console, thereby letting the pixies consume it. This causes no heat to be produced at all, keeps the pixies happy and gets rid of your data quite quickly, even if it does make things look a bit messy on your screen. Incidentally, as an ex-admin of a large ISP who experienced many problems attempting to maintain a stable temperature in a server room, I would strongly discourage people sending the data they do not want out to the network. The fairies who do the packet switching and routing get annoyed by it as well. Advanced Topics How can I learn more about FreeBSD's internals? At this time, there is no book on FreeBSD-specific OS internals. Much general UNIX knowledge is directly applicable to FreeBSD, however. Additionally, there are BSD-specific books that are still relevant. For a list, please check the Handbook's Operating System Internals Bibliography. How can I contribute to FreeBSD? Please see the article on Contributing to FreeBSD for specific advice on how to do this. Assistance is more than welcome! What are SNAPs and RELEASEs? There are currently three active/semi-active branches in the FreeBSD CVS Repository (the RELENG_2 branch is probably only changed twice a year, which is why there are only three active branches of development): RELENG_2_2 AKA 2.2-STABLE RELENG_3 AKA 3.X-STABLE RELENG_4 AKA 4-STABLE HEAD AKA -CURRENT AKA 5.0-CURRENT HEAD is not an actual branch tag, like the other two; it is simply a symbolic constant for the current, non-branched development stream which we simply refer to as -CURRENT. Right now, -CURRENT is the 5.0 development stream and the 4-STABLE branch, RELENG_4, forked off from -CURRENT in Mar 2000. The 2.2-STABLE branch, RELENG_2_2, departed -CURRENT in November 1996, and has pretty much been retired. How do I make my own custom release? Please see the Release Engineering article. Why does make world clobber my existing installed binaries? Yes, this is the general idea; as its name might suggest, make world rebuilds every system binary from scratch, so you can be certain of having a clean and consistent environment at the end (which is why it takes so long). If the environment variable DESTDIR is defined while running make world or make install, the newly-created binaries will be deposited in a directory tree identical to the installed one, rooted at ${DESTDIR}. Some random combination of shared libraries modifications and program rebuilds can cause this to fail in make world however. Why does my system say (bus speed defaulted) when it boots? The Adaptec 1542 SCSI host adapters allow the user to configure their bus access speed in software. Previous versions of the 1542 driver tried to determine the fastest usable speed and set the adapter to that. We found that this breaks some users' systems, so you now have to define the TUNE_1542 kernel configuration option in order to have this take place. Using it on those systems where it works may make your disks run faster, but on those systems where it does not, your data could be corrupted. Can I follow -CURRENT with limited Internet access? Yes, you can do this without downloading the whole source tree by using the CTM facility. How did you split the distribution into 240k files? Newer BSD based systems have a option to split that allows them to split files on arbitrary byte boundaries. Here is an example from /usr/src/Makefile. bin-tarball: (cd ${DISTDIR}; \ tar cf - . \ gzip --no-name -9 -c | \ split -b 240640 - \ ${RELEASEDIR}/tarballs/bindist/bin_tgz.) I have written a kernel extension, who do I send it to? Please take a look at the article on Contributing to FreeBSD to learn how to submit code. And thanks for the thought! How are Plug N Play ISA cards detected and initialized? By: Frank Durda IV uhclem@nemesis.lonestar.org In a nutshell, there a few I/O ports that all of the PnP boards respond to when the host asks if anyone is out there. So when the PnP probe routine starts, it asks if there are any PnP boards present, and all the PnP boards respond with their model # to a I/O read of the same port, so the probe routine gets a wired-OR yes to that question. At least one bit will be on in that reply. Then the probe code is able to cause boards with board model IDs (assigned by Microsoft/Intel) lower than X to go off-line. It then looks to see if any boards are still responding to the query. If the answer was 0, then there are no boards with IDs above X. Now probe asks if there are any boards below X. If so, probe knows there are boards with a model numbers below X. Probe then asks for boards greater than X-(limit/4) to go off-line. If repeats the query. By repeating this semi-binary search of IDs-in-range enough times, the probing code will eventually identify all PnP boards present in a given machine with a number of iterations that is much lower than what 2^64 would take. The IDs are two 32-bit fields (hence 2ˆ64) + 8 bit checksum. The first 32 bits are a vendor identifier. They never come out and say it, but it appears to be assumed that different types of boards from the same vendor could have different 32-bit vendor ids. The idea of needing 32 bits just for unique manufacturers is a bit excessive. The lower 32 bits are a serial #, Ethernet address, something that makes this one board unique. The vendor must never produce a second board that has the same lower 32 bits unless the upper 32 bits are also different. So you can have multiple boards of the same type in the machine and the full 64 bits will still be unique. The 32 bit groups can never be all zero. This allows the wired-OR to show non-zero bits during the initial binary search. Once the system has identified all the board IDs present, it will reactivate each board, one at a time (via the same I/O ports), and find out what resources the given board needs, what interrupt choices are available, etc. A scan is made over all the boards to collect this information. This info is then combined with info from any ECU files on the hard disk or wired into the MLB BIOS. The ECU and BIOS PnP support for hardware on the MLB is usually synthetic, and the peripherals do not really do genuine PnP. However by examining the BIOS info plus the ECU info, the probe routines can cause the devices that are PnP to avoid those devices the probe code cannot relocate. Then the PnP devices are visited once more and given their I/O, DMA, IRQ and Memory-map address assignments. The devices will then appear at those locations and remain there until the next reboot, although there is nothing that says you cannot move them around whenever you want. There is a lot of oversimplification above, but you should get the general idea. Microsoft took over some of the primary printer status ports to do PnP, on the logic that no boards decoded those addresses for the opposing I/O cycles. I found a genuine IBM printer board that did decode writes of the status port during the early PnP proposal review period, but MS said tough. So they do a write to the printer status port for setting addresses, plus that use that address + 0x800, and a third I/O port for reading that can be located anywhere between 0x200 and 0x3ff. Can you assign a major number for a device driver I have written? This depends on whether or not you plan on making the driver publicly available. If you do, then please send us a copy of the driver source code, plus the appropriate modifications to files.i386, a sample configuration file entry, and the appropriate &man.MAKEDEV.8; code to create any special files your device uses. If you do not, or are unable to because of licensing restrictions, then character major number 32 and block major number 8 have been reserved specifically for this purpose; please use them. In any case, we would appreciate hearing about your driver on &a.hackers;. What about alternative layout policies for directories? In answer to the question of alternative layout policies for directories, the scheme that is currently in use is unchanged from what I wrote in 1983. I wrote that policy for the original fast filesystem, and never revisited it. It works well at keeping cylinder groups from filling up. As several of you have noted, it works poorly for find. Most filesystems are created from archives that were created by a depth first search (aka ftw). These directories end up being striped across the cylinder groups thus creating a worst possible scenario for future depth first searches. If one knew the total number of directories to be created, the solution would be to create (total / fs_ncg) per cylinder group before moving on. Obviously, one would have to create some heuristic to guess at this number. Even using a small fixed number like say 10 would make an order of magnitude improvement. To differentiate restores from normal operation (when the current algorithm is probably more sensible), you could use the clustering of up to 10 if they were all done within a ten second window. Anyway, my conclusion is that this is an area ripe for experimentation. Kirk McKusick, September 1998 How can I make the most of the data I see when my kernel panics? [This section was extracted from a mail written by &a.wpaul; on the freebsd-current mailing list by &a.des;, who fixed a few typos and added the bracketed comments] From: Bill Paul <wpaul@skynet.ctr.columbia.edu> Subject: Re: the fs fun never stops To: Ben Rosengart Date: Sun, 20 Sep 1998 15:22:50 -0400 (EDT) Cc: current@FreeBSD.org Ben Rosengart posted the following panic message] > Fatal trap 12: page fault while in kernel mode > fault virtual address = 0x40 > fault code = supervisor read, page not present > instruction pointer = 0x8:0xf014a7e5 ^^^^^^^^^^ > stack pointer = 0x10:0xf4ed6f24 > frame pointer = 0x10:0xf4ed6f28 > code segment = base 0x0, limit 0xfffff, type 0x1b > = DPL 0, pres 1, def32 1, gran 1 > processor eflags = interrupt enabled, resume, IOPL = 0 > current process = 80 (mount) > interrupt mask = > trap number = 12 > panic: page fault [When] you see a message like this, it is not enough to just reproduce it and send it in. The instruction pointer value that I highlighted up there is important; unfortunately, it is also configuration dependent. In other words, the value varies depending on the exact kernel image that you are using. If you are using a GENERIC kernel image from one of the snapshots, then it is possible for somebody else to track down the offending function, but if you are running a custom kernel then only you can tell us where the fault occurred. What you should do is this: Write down the instruction pointer value. Note that the 0x8: part at the beginning is not significant in this case: it is the 0xf0xxxxxx part that we want. When the system reboots, do the following: &prompt.user; nm -n /kernel.that.caused.the.panic | grep f0xxxxxx where f0xxxxxx is the instruction pointer value. The odds are you will not get an exact match since the symbols in the kernel symbol table are for the entry points of functions and the instruction pointer address will be somewhere inside a function, not at the start. If you do not get an exact match, omit the last digit from the instruction pointer value and try again, i.e.: &prompt.user; nm -n /kernel.that.caused.the.panic | grep f0xxxxx If that does not yield any results, chop off another digit. Repeat until you get some sort of output. The result will be a possible list of functions which caused the panic. This is a less than exact mechanism for tracking down the point of failure, but it is better than nothing. I see people constantly show panic messages like this but rarely do I see someone take the time to match up the instruction pointer with a function in the kernel symbol table. The best way to track down the cause of a panic is by capturing a crash dump, then using &man.gdb.1; to generate a stack trace on the crash dump. In any case, the method I normally use is this: Set up a kernel config file, optionally adding options DDB if you think you need the kernel debugger for something. (I use this mainly for setting breakpoints if I suspect an infinite loop condition of some kind.) Use config -g KERNELCONFIG to set up the build directory. cd /sys/compile/ KERNELCONFIG; make Wait for kernel to finish compiling. make install reboot The &man.make.1; process will have built two kernels. kernel and kernel.debug. kernel was installed as /kernel, while kernel.debug can be used as the source of debugging symbols for &man.gdb.1;. To make sure you capture a crash dump, you need edit /etc/rc.conf and set dumpdev to point to your swap partition. This will cause the &man.rc.8; scripts to use the &man.dumpon.8; command to enable crash dumps. You can also run &man.dumpon.8; manually. After a panic, the crash dump can be recovered using &man.savecore.8;; if dumpdev is set in /etc/rc.conf, the &man.rc.8; scripts will run &man.savecore.8; automatically and put the crash dump in /var/crash. FreeBSD crash dumps are usually the same size as the physical RAM size of your machine. That is, if you have 64MB of RAM, you will get a 64MB crash dump. Therefore you must make sure there is enough space in /var/crash to hold the dump. Alternatively, you run &man.savecore.8; manually and have it recover the crash dump to another directory where you have more room. It is possible to limit the size of the crash dump by using options MAXMEM=(foo) to set the amount of memory the kernel will use to something a little more sensible. For example, if you have 128MB of RAM, you can limit the kernel's memory usage to 16MB so that your crash dump size will be 16MB instead of 128MB. Once you have recovered the crash dump, you can get a stack trace with &man.gdb.1; as follows: &prompt.user; gdb -k /sys/compile/KERNELCONFIG/kernel.debug /var/crash/vmcore.0 (gdb) where Note that there may be several screens worth of information; ideally you should use &man.script.1; to capture all of them. Using the unstripped kernel image with all the debug symbols should show the exact line of kernel source code where the panic occurred. Usually you have to read the stack trace from the bottom up in order to trace the exact sequence of events that lead to the crash. You can also use &man.gdb.1; to print out the contents of various variables or structures in order to examine the system state at the time of the crash. Now, if you are really insane and have a second computer, you can also configure &man.gdb.1; to do remote debugging such that you can use &man.gdb.1; on one system to debug the kernel on another system, including setting breakpoints, single-stepping through the kernel code, just like you can do with a normal user-mode program. I have not played with this yet as I do not often have the chance to set up two machines side by side for debugging purposes. [Bill adds: "I forgot to mention one thing: if you have DDB enabled and the kernel drops into the debugger, you can force a panic (and a crash dump) just by typing 'panic' at the ddb prompt. It may stop in the debugger again during the panic phase. If it does, type 'continue' and it will finish the crash dump." -ed] Why has dlsym() stopped working for ELF executables? The ELF toolchain does not, by default, make the symbols defined in an executable visible to the dynamic linker. Consequently dlsym() searches on handles obtained from calls to dlopen(NULL, flags) will fail to find such symbols. If you want to search, using dlsym(), for symbols present in the main executable of a process, you need to link the executable using the option to the ELF linker (&man.ld.1;). How can I increase or reduce the kernel address space? By default, the kernel address space is 256 MB on FreeBSD 3.x and 1 GB on FreeBSD 4.x. If you run a network-intensive server (e.g. a large FTP or HTTP server), you might find that 256 MB is not enough. So how do you increase the address space? There are two aspects to this. First, you need to tell the kernel to reserve a larger portion of the address space for itself. Second, since the kernel is loaded at the top of the address space, you need to lower the load address so it does not bump its head against the ceiling. The first goal is achieved by increasing the value of NKPDE in src/sys/i386/include/pmap.h. Here is what it looks like for a 1 GB address space: #ifndef NKPDE #ifdef SMP #define NKPDE 254 /* addressable number of page tables/pde's */ #else #define NKPDE 255 /* addressable number of page tables/pde's */ #endif /* SMP */ #endif To find the correct value of NKPDE, divide the desired address space size (in megabytes) by four, then subtract one for UP and two for SMP. To achieve the second goal, you need to compute the correct load address: simply subtract the address space size (in bytes) from 0x100100000; the result is 0xc0100000 for a 1 GB address space. Set LOAD_ADDRESS in src/sys/i386/conf/Makefile.i386 to that value; then set the location counter in the beginning of the section listing in src/sys/i386/conf/kernel.script to the same value, as follows: OUTPUT_FORMAT("elf32-i386", "elf32-i386", "elf32-i386") OUTPUT_ARCH(i386) ENTRY(btext) SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/obj/elf/home/src/tmp/usr/i386-unknown-freebsdelf/lib); SECTIONS { /* Read-only sections, merged into text segment: */ . = 0xc0100000 + SIZEOF_HEADERS; .interp : { *(.interp) } Then reconfig and rebuild your kernel. You will probably have problems with &man.ps.1; &man.top.1; and the like; make world should take care of it (or a manual rebuild of libkvm, &man.ps.1; and &man.top.1; after copying the patched pmap.h to /usr/include/vm/. NOTE: the size of the kernel address space must be a multiple of four megabytes. [&a.dg; adds: I think the kernel address space needs to be a power of two, but I am not certain about that. The old(er) boot code used to monkey with the high order address bits and I think expected at least 256MB granularity.] Acknowledgments
FreeBSD Core Team If you see a problem with this FAQ, or wish to submit an entry, please mail the &a.faq;. We appreciate your feedback, and cannot make this a better FAQ without your help!
&a.jkh; Occasional fits of FAQ-reshuffling and updating. &a.dwhite; Services above and beyond the call of duty on freebsd-questions &a.joerg; Services above and beyond the call of duty on Usenet &a.wollman; Networking and formatting Jim Lowe Multicast information &a.pds; FreeBSD FAQ typing machine slavey The FreeBSD Team Kvetching, moaning, submitting data And to any others we have forgotten, apologies and heartfelt thanks! &bibliography; diff --git a/en_US.ISO8859-1/books/fdp-primer/the-website/chapter.sgml b/en_US.ISO8859-1/books/fdp-primer/the-website/chapter.sgml index 6f90b37f65..5b696a288a 100644 --- a/en_US.ISO8859-1/books/fdp-primer/the-website/chapter.sgml +++ b/en_US.ISO8859-1/books/fdp-primer/the-website/chapter.sgml @@ -1,218 +1,218 @@ The Website Preparation Get 200MB free disk space. You will need the disk space for the SGML tools, a subset of the CVS tree, temporary build space and the installed web pages. If you already have installed the SGML tools and the CVS tree, you need only ~100MB free disk space. Make sure your documentation ports are up to date! When in doubt, remove the old ports using &man.pkg.delete.1; command before installing the port. For example, we currently depend on jade-1.2 and if you have installed jade-1.1, please do &prompt.root; pkg_delete jade-1.1 Setup a CVS repository. You need the directories www, doc and ports in the CVS tree (plus the CVSROOT of course). Please read the CVSup introduction - http://www.FreeBSD.org/handbook/synching.html#CVSUP how to + http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/synching.html#CVSUP how to mirror a CVS tree or parts of a CVS tree. The essential cvsup collections are: www, doc-all, cvs-base, and ports-base. These collections require ~100MB free disk space. A full CVS tree - including src, doc, www, and ports - is currently 650MB large. Build the web pages from scratch Go to into a build directory with at least 60MB of free space. &prompt.root; mkdir /var/tmp/webbuild &prompt.root; cd /var/tmp/webbuild Checkout the SGML files from the CVS tree. &prompt.root; cvs -R co www doc Change into the www directory, and run the &man.make.1; links target, to create the necessary symbolic links. &prompt.root; cd www &prompt.root; make links Change into the en directory, and run the &man.make.1; all target, to create the web pages. &prompt.root; cd en &prompt.root; make all Install the web pages into your web server If you have moved out of the en directory, change back to it. &prompt.root; cd path/www/en Run the &man.make.1; install target, setting the DESTDIR variable to the name of the directory you want to install the files to. &prompt.root; make DESTDIR=/usr/local/www install If you have previously installed the web pages into the same directory the install process will not have deleted any old or outdated pages. For example, if you build and install a new copy of the site every day, this command will find and delete all files that have not been updated in three days. &prompt.root; find /usr/local/www -ctime 3 -print0 | xargs -0 rm Environment variables CVSROOT Location of the CVS tree. Essential. &prompt.root; CVSROOT=/home/ncvs; export CVSROOT ENGLISH_ONLY If set and not empty, the makefiles will build and install only the English documents. All translations will be ignored. E.g.: &prompt.root; make ENGLISH_ONLY=YES all install If you want unset the variable ENGLISH_ONLY and build all pages, including translations, set the variable ENGLISH_ONLY to an empty value &prompt.root; make ENGLISH_ONLY="" all install clean WEB_ONLY If set and not empty, the makefiles will build and install only the HTML pages from the www directory. All documents from the doc directory (Handbook, FAQ, Tutorials) will be ignored. E.g.: &prompt.root; make WEB_ONLY=YES all install NOPORTSCVS If set, the makefiles will not checkout files from the ports cvs repository. Instead, it will copy the files from /usr/ports (or where the variable PORTSBASE points to). CVSROOT is an environment variable. You must set it on the command line or in your dot files (~/.profile). WEB_ONLY, ENGLISH_ONLY and NOPORTSCVS are makefile variables. You can set the variables in /etc/make.conf, Makefile.inc or as environment variables on the command line or in your dot files. diff --git a/en_US.ISO8859-1/books/handbook/kernelconfig/chapter.sgml b/en_US.ISO8859-1/books/handbook/kernelconfig/chapter.sgml index b456f80cc2..6be84ea75a 100644 --- a/en_US.ISO8859-1/books/handbook/kernelconfig/chapter.sgml +++ b/en_US.ISO8859-1/books/handbook/kernelconfig/chapter.sgml @@ -1,1396 +1,1396 @@ Jim Mock Updated and restructured by Jake Hamby Originally contributed by Configuring the FreeBSD Kernel Synopsis kernel building a custom kernel The kernel is the core of the FreeBSD operating system. It is responsible for managing memory, enforcing security controls, networking, disk access, and much more. While more and more of FreeBSD becomes dynamically configurable it is still occasionally necessary to reconfigure and recompile your kernel. After reading this chapter, you will know: Why you might need to build a custom kernel. How to write a kernel configuration file, or alter an existing configuration file. How to use the kernel configuration file to create and build a new kernel. How to install the new kernel. How to create any entries in /dev that may be required. How to troubleshoot if things go wrong. Why Build a Custom Kernel? Traditionally, FreeBSD has had what is called a monolithic kernel. This means that the kernel was one large program, supported a fixed list of devices, and if you wanted to change the kernel's behavior then you had to compile a new kernel, and then reboot your computer with the new kernel. Today, FreeBSD is rapidly moving to a model where much of the kernel's functionality is contained in modules which can be dynamically loaded and unloaded from the kernel as necessary. This allows the kernel to adapt to new hardware suddenly becoming available (such as PCMCIA cards in a laptop), or for new functionality to be brought into the kernel that was not necessary when the kernel was originally compiled. Colloquially these are called KLDs. Despite this, it is still necessary to carry out some static kernel configuration. In some cases this is because the functionality is so tied to the kernel that it can not be made dynamically loadable. In others it may simply be because no one has yet taken the time to write a dynamic loadable kernel module for that functionality yet. Building a custom kernel is one of the most important rites of passage nearly every Unix user must endure. This process, while time consuming, will provide many benefits to your FreeBSD system. Unlike the GENERIC kernel, which must support a wide range of hardware, a custom kernel only contains support for your PC's hardware. This has a number of benefits, such as: Faster boot time. Since the kernel will only probe the hardware you have on your system, the time it takes your system to boot will decrease dramatically. Less memory usage. A custom kernel often uses less memory than the GENERIC kernel, which is important because the kernel must always be present in real memory. For this reason, a custom kernel is especially useful on a system with a small amount of RAM. Additional hardware support. A custom kernel allows you to add in support for devices such as sound cards, which are not present in the GENERIC kernel. Building and Installing a Custom Kernel kernel building / installing First, let us take a quick tour of the kernel build directory. All directories mentioned will be relative to the main /usr/src/sys directory, which is also accessible through /sys. There are a number of subdirectories here representing different parts of the kernel, but the most important, for our purposes, are arch/conf, where you will edit your custom kernel configuration, and compile, which is the staging area where your kernel will be built. arch represents either i386, alpha, or pc98 (an alternative development branch of PC hardware, popular in Japan). Everything inside a particular architecture's directory deals with that architecture only; the rest of the code is common to all platforms to which FreeBSD could potentially be ported. Notice the logical organization of the directory structure, with each supported device, filesystem, and option in its own subdirectory. If there is not a /usr/src/sys directory on your system, then the kernel source has not been installed. The easiest way to do this is by running /stand/sysinstall as root, choosing Configure, then Distributions, then src, then sys. If you have an aversion to sysinstall and you have access to an official FreeBSD CDROM, then you can also install the source from the command line: &prompt.root; mount /cdrom &prompt.root; mkdir -p /usr/src/sys &prompt.root; ln -s /usr/src/sys /sys &prompt.root; cat /cdrom/sys/ssys.[a-d]* | tar -xzvf Next, move to the arch/conf directory and copy the GENERIC configuration file to the name you want to give your kernel. For example: &prompt.root; cd /usr/src/sys/i386/conf &prompt.root; cp GENERIC MYKERNEL Traditionally, this name is in all capital letters and, if you are maintaining multiple FreeBSD machines with different hardware, it is a good idea to name it after your machine's hostname. We will call it MYKERNEL for the purpose of this example. Storing your kernel config file directly under /usr/src can be a bad idea. If you are experiencing problems it can be tempting to just delete /usr/src and start again. Five seconds after you do that you realize that you have deleted your custom kernel config file. You might want to keep your kernel config file elsewhere, and then create a symbolic link to the file in the i386 directory. For example: &prompt.root; cd /usr/src/sys/i386/conf &prompt.root; mkdir /root/kernels &prompt.root; cp GENERIC /root/kernels/MYKERNEL &prompt.root; ln -s /root/kernels/MYKERNEL You must execute these and all of the following commands under the root account or you will get permission denied errors. Now, edit MYKERNEL with your favorite text editor. If you are just starting out, the only editor available will probably be vi, which is too complex to explain here, but is covered well in many books in the bibliography. However, FreeBSD does offer an easier editor called ee which, if you are a beginner, should be your editor of choice. Feel free to change the comment lines at the top to reflect your configuration or the changes you have made to differentiate it from GENERIC. SunOS If you have built a kernel under SunOS or some other BSD operating system, much of this file will be very familiar to you. If you are coming from some other operating system such as DOS, on the other hand, the GENERIC configuration file might seem overwhelming to you, so follow the descriptions in the Configuration File section slowly and carefully. Be sure to always check the file /usr/src/UPDATING, before you perform any update steps, in the case you sync your source-tree with the latest sources of the FreeBSD project. In this file all important issues with updating FreeBSD are written down. /usr/src/UPDATING always fits to your version of the FreeBSD source, and is therefore more accurate for those information than the handbook. You must now compile the source code for the kernel. There are two procedures you can use to do this, and the one you will use depends on why you are rebuilding the kernel, and the version of FreeBSD you are running. If you have installed only the kernel source code, use procedure 1. If you are running a FreeBSD version prior to 4.0, and you are not upgrading to FreeBSD 4.0 or higher using the make world procedure, use procedure 1. If you are building a new kernel without updating the source code (perhaps just to add a new option, such as IPFIREWALL) you can use either procedure. If you are rebuilding the kernel as part of a make world process, use procedure 2. Procedure 1. Building a kernel the <quote>traditional</quote> way Run &man.config.8; to generate the kernel source code. &prompt.root; /usr/sbin/config MYKERNEL Change into the build directory. &prompt.root; cd ../../compile/MYKERNEL Compile the kernel. &prompt.root; make depend &prompt.root; make Install the new kernel. &prompt.root; make install Procedure 2. Building a kernel the <quote>new</quote> way Change to the /usr/src directory. &prompt.root; cd /usr/src Compile the kernel. &prompt.root; make buildkernel KERNCONF=MYKERNEL Install the new kernel. &prompt.root; make installkernel KERNCONF=MYKERNEL In FreeBSD 4.2 and older you must replace KERNCONF= with KERNEL=. 4.2-STABLE that was fetched after Feb 2nd, 2001 does recognize KERNCONF=. cvsup anonymous CVS CTM CVS anonymous If you have not upgraded your source tree in any way (you have not run CVSup, CTM, or used anoncvs), then you should use the config, make depend, make, make install sequence. kernel.old The new kernel will be copied to the root directory as /kernel and the old kernel will be moved to /kernel.old. Now, shutdown the system and reboot to use your kernel. In case something goes wrong, there are some troubleshooting instructions at the end of this chapter. Be sure to read the section which explains how to recover in case your new kernel does not boot. If you have added any new devices (such as sound cards) you may have to add some device nodes to your /dev directory before you can use them. For more information, take a look at "Making Device Nodes" later on in this chapter. The Configuration File kernel LINT LINT kernel config file The general format of a configuration file is quite simple. Each line contains a keyword and one or more arguments. For simplicity, most lines only contain one argument. Anything following a # is considered a comment and ignored. The following sections describe each keyword, generally in the order they are listed in GENERIC, although some related keywords have been grouped together in a single section (such as Networking) even though they are actually scattered throughout the GENERIC file. An exhaustive list of options and more detailed explanations of the device lines is present in the LINT configuration file, located in the same directory as GENERIC. If you are in doubt as to the purpose or necessity of a line, check first in LINT. Quoting numbers In all versions of FreeBSD up to and including 3.X, &man.config.8; required that any strings in the configuration file that contained numbers used as text had to be enclosed in double quotes. This requirement was removed in the 4.X branch, which this book covers, so if you are on a pre-4.X system, see the /usr/src/sys/i386/conf/LINT and /usr/src/sys/i386/conf/GENERIC files on your system for examples. kernel example config file The following is an example GENERIC kernel configuration file with various additional comments where needed for clarity. This example should match your copy in /usr/src/sys/i386/conf/GENERIC fairly closely. For details of all the possible kernel options, see /usr/src/sys/i386/conf/LINT. # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # -# http://www.FreeBSD.org/handbook/kernelconfig-config.html +# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246 2000/03/09 16:32:55 jlemon Exp $ The following are the mandatory keywords required in every kernel you build: kernel options machine machine i386 This is the machine architecture. It must be either i386, alpha, or pc98. kernel options cpu cpu I386_CPU cpu I486_CPU cpu I586_CPU cpu I686_CPU The above specifies the type of CPU you have in your system. You may have multiple instances of the CPU line (i.e., you are not sure whether you should use I586_CPU or I686_CPU), however, for a custom kernel, it is best to specify only the CPU you have. If you are unsure of your CPU type, you can use the dmesg command to view your boot up messages. kernel options cpu type The Alpha architecture has different values for cpu. They include: cpu EV4 cpu EV5 If you are using an Alpha machine, you should be using one of the above CPU types. kernel options ident ident GENERIC This is the identification of the kernel. You should change this to whatever you named your kernel, as in our previous example, MYKERNEL. The value you put in the ident string will print when you boot up the kernel, so it is useful to give the new kernel a different name if you want to keep it separate from your usual kernel (i.e., you want to build an experimental kernel). kernel options maxusers maxusers n The maxusers option sets the size of a number of important system tables. This number is supposed to be roughly equal to the number of simultaneous users you expect to have on your machine. Starting with FreeBSD 4.5, the system will auto-tune this setting for you if you explicitly set it to 0 The auto-tuning algorithm sets maxuser equal to the amount of memory in the system, with a minimum of 32, and a maximum of 384.. If you are using an earlier version of FreeBSD, or you want to manage it yourself you will want to set maxusers to at least 4, especially if you are using the X Window System or compiling software. The reason is that the most important table set by maxusers is the maximum number of processes, which is set to 20 + 16 * maxusers, so if you set maxusers to 1, then you can only have 36 simultaneous processes, including the 18 or so that the system starts up at boot time, and the 15 or so you will probably create when you start the X Window System. Even a simple task like reading a manual page will start up nine processes to filter, decompress, and view it. Setting maxusers to 64 will allow you to have up to 1044 simultaneous processes, which should be enough for nearly all uses. If, however, you see the dreaded proc table full error when trying to start another program, or are running a server with a large number of simultaneous users (like ftp.FreeBSD.org), you can always increase the number and rebuild. maxusers does not limit the number of users which can log into your machine. It simply sets various table sizes to reasonable values considering the maximum number of users you will likely have on your system and how many processes each of them will be running. One keyword which does limit the number of simultaneous remote logins is pseudo-device pty 16. # Floating point support - do not disable. device npx0 at nexus? port IO_NPX irq 13 npx0 is the interface to the floating point math unit in FreeBSD, which is either the hardware co-processor or the software math emulator. This is not optional. # Pseudo devices - the number indicates how many units to allocate. pseudo-device loop # Network loopback This is the generic loopback device for TCP/IP. If you telnet or FTP to localhost (a.k.a., 127.0.0.1) it will come back at you through this pseudo-device. This is mandatory. Everything that follows is more or less optional. See the notes underneath or next to each option for more information. #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols options MATH_EMULATE #Support for x87 emulation This line allows the kernel to simulate a math co-processor if your computer does not have one (386 or 486SX). If you have a 486DX, or a 386 or 486SX (with a separate 387 or 487 chip), or higher (Pentium, Pentium II, etc.), you can comment this line out. The normal math co-processor emulation routines that come with FreeBSD are not very accurate. If you do not have a math co-processor, and you need the best accuracy, it is recommended that you change this option to GPL_MATH_EMULATE to use the GNU math support, which is not included by default for licensing reasons. options INET #InterNETworking Networking support. Leave this in, even if you do not plan to be connected to a network. Most programs require at least loopback networking (i.e., making network connections within your PC), so this is essentially mandatory. options INET6 #IPv6 communications protocols This enables the IPv6 communication protocols. options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] This is the basic hard drive filesystem. Leave it in if you boot from the hard disk. options UFS_DIRHASH #Improve performance on big directories This option includes some code to speed up disk operations on large directories, at the expense of using a some additional memory. You would normally keep this for a large server, or interactive workstation, and remove it if you are using FreeBSD on a smaller system where memory is at a premium and disk access speed is less important, such as a firewall. options SOFTUPDATES #Enable FFS soft updates support This option enables soft updates in the kernel, this will help speed up write access on the disks. They are enabled by default in the 4.X branch but may not be turned on. Review the output from &man.mount.8; to see if you have them enabled. If you do not see the soft-updates option then you will need to activate it using the &man.tunefs.8; or &man.newfs.8; for new filesystems. options MFS #Memory Filesystem options MD_ROOT #MD is a potential root device This is the memory-mapped filesystem. This is basically a RAM disk for fast storage of temporary files, useful if you have a lot of swap space that you want to take advantage of. A perfect place to mount an MFS partition is on the /tmp directory, since many programs store temporary data here. To mount an MFS RAM disk on /tmp, add the following line to /etc/fstab: /dev/ad1s2b /tmp mfs rw 0 0 Now you simply need to either reboot, or run the command mount /tmp. kernel options NFS kernel options NFS_ROOT options NFS #Network Filesystem options NFS_ROOT #NFS usable as root device, NFS required The network filesystem. Unless you plan to mount partitions from a Unix file server over TCP/IP, you can comment these out. kernel options MSDOSFS options MSDOSFS #MSDOS Filesystem The MS-DOS filesystem. Unless you plan to mount a DOS formatted hard drive partition at boot time, you can safely comment this out. It will be automatically loaded the first time you mount a DOS partition, as described above. Also, the excellent mtools software (in the ports collection) allows you to access DOS floppies without having to mount and unmount them (and does not require MSDOSFS at all). options CD9660 #ISO 9660 Filesystem options CD9660_ROOT #CD-ROM usable as root, CD9660 required The ISO 9660 filesystem for CDROMs. Comment it out if you do not have a CDROM drive or only mount data CDs occasionally (since it will be dynamically loaded the first time you mount a data CD). Audio CDs do not need this filesystem. options PROCFS #Process filesystem The process filesystem. This is a pretend filesystem mounted on /proc which allows programs like &man.ps.1; to give you more information on what processes are running. options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] Compatibility with 4.3BSD. Leave this in; some programs will act strangely if you comment this out. options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI This causes the kernel to pause for 15 seconds before probing each SCSI device in your system. If you only have IDE hard drives, you can ignore this, otherwise you will probably want to lower this number, perhaps to 5 seconds, to speed up booting. Of course, if you do this, and FreeBSD has trouble recognizing your SCSI devices, you will have to raise it back up. options UCONSOLE #Allow users to grab the console Allow users to grab the console, which is useful for X users. For example, you can create a console xterm by typing xterm -C, which will display any write, talk, and any other messages you receive, as well as any console messages sent by the kernel. options USERCONFIG #boot -c editor This option allows you to boot the configuration editor from the boot menu. options VISUAL_USERCONFIG #visual boot -c editor This option allows you to boot the visual configuration editor from the boot menu. options KTRACE #ktrace(1) support This enables kernel process tracing, which is useful in debugging. options SYSVSHM #SYSV-style shared memory This option provides for System V shared memory. The most common use of this is the XSHM extension in X, which many graphics-intensive programs will automatically take advantage of for extra speed. If you use X, you will definitely want to include this. options SYSVSEM #SYSV-style semaphores Support for System V semaphores. Less commonly used but only adds a few hundred bytes to the kernel. options SYSVMSG #SYSV-style message queues Support for System V messages. Again, only adds a few hundred bytes to the kernel. The &man.ipcs.1; command will list any processes using each of these System V facilities. options P1003_1B #Posix P1003_1B real-time extensions options _KPOSIX_PRIORITY_SCHEDULING Real-time extensions added in the 1993 POSIX. Certain applications in the ports collection use these (such as StarOffice). kernel options ICMP_BANDLIM Denial of Service (DoS) options ICMP_BANDLIM #Rate limit bad replies This option enables ICMP error response bandwidth limiting. You typically want this option as it will help protect the machine from denial of service packet attacks. kernel options SMP # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O The above are both required for SMP support. device isa All PCs supported by FreeBSD have one of these. If you have an IBM PS/2 (Micro Channel Architecture), you cannot run FreeBSD at this time (support is being worked on). device eisa Include this if you have an EISA motherboard. This enables auto-detection and configuration support for all devices on the EISA bus. device pci Include this if you have a PCI motherboard. This enables auto-detection of PCI cards and gatewaying from the PCI to ISA bus. # Floppy drives device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 device fd1 at fdc0 drive 1 This is the floppy drive controller. fd0 is the A: floppy drive, and fd1 is the B: drive. device ata This driver supports all ATA and ATAPI devices. You only need one device ata line for the kernel to detect all PCI ATA/ATAPI devices on modern machines. device atadisk # ATA disk drives This is needed along with device ata for ATAPI disk drives. device atapicd # ATAPI CDROM drives This is needed along with device ata for ATAPI CDROM drives. device atapifd # ATAPI floppy drives This is needed along with device ata for ATAPI floppy drives. device atapist # ATAPI tape drives This is needed along with device ata for ATAPI tape drives. options ATA_STATIC_ID #Static device numbering This makes the controller number static (like the old driver) or else the device numbers are dynamically allocated. # ATA and ATAPI devices device ata0 at isa? port IO_WD1 irq 14 device ata1 at isa? port IO_WD2 irq 15 Use the above for older, non-PCI systems. # SCSI Controllers device ahb # EISA AHA1742 family device ahc # AHA2940 and onboard AIC7xxx devices device amd # AMD 53C974 (Teckram DC-390(T)) device dpt # DPT Smartcache - See LINT for options! device isp # Qlogic family device ncr # NCR/Symbios Logic device sym # NCR/Symbios Logic (newer chipsets) device adv0 at isa? device adw device bt0 at isa? device aha0 at isa? device aic0 at isa? SCSI controllers. Comment out any you do not have in your system. If you have an IDE only system, you can remove these altogether. # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) SCSI peripherals. Again, comment out any you do not have, or if you have only IDE hardware, you can remove them completely. # RAID controllers device ida # Compaq Smart RAID device amr # AMI MegaRAID device mlx # Mylex DAC960 family Supported RAID controllers. If you do not have any of these, you can comment them out or remove them. # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc0 at isa? port IO_KBD The keyboard controller (atkbdc) provides I/O services for the AT keyboard and PS/2 style pointing devices. This controller is required by the keyboard driver (atkbd) and the PS/2 pointing device driver (psm). device atkbd0 at atkbdc? irq 1 The atkbd driver, together with atkbdc controller, provides access to the AT 84 keyboard or the AT enhanced keyboard which is connected to the AT keyboard controller. device psm0 at atkbdc? irq 12 Use this device if your mouse plugs into the PS/2 mouse port. device vga0 at isa? The video card driver. # splash screen/screen saver pseudo-device splash Splash screen at start up! Screen savers require this too. # syscons is the default console driver, resembling an SCO console device sc0 at isa? sc0 is the default console driver, which resembles a SCO console. Since most full-screen programs access the console through a terminal database library like termcap, it should not matter whether you use this or vt0, the VT220 compatible console driver. When you log in, set your TERM variable to scoansi if full-screen programs have trouble running under this console. # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std This is a VT220-compatible console driver, backward compatible to VT100/102. It works well on some laptops which have hardware incompatibilities with sc0. Also set your TERM variable to vt100 or vt220 when you log in. This driver might also prove useful when connecting to a large number of different machines over the network, where termcap or terminfo entries for the sc0 device are often not available — vt100 should be available on virtually any platform. # Power management support (see LINT for more options) device apm0 at nexus? disable flags 0x20 # Advanced Power Management Advanced Power Management support. Useful for laptops. # PCCARD (PCMCIA) support device card device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000 device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable PCMCIA support. You want this if you are using a laptop. # Serial (COM) ports device sio0 at isa? port IO_COM1 flags 0x10 irq 4 device sio1 at isa? port IO_COM2 irq 3 device sio2 at isa? disable port IO_COM3 irq 5 device sio3 at isa? disable port IO_COM4 irq 9 These are the four serial ports referred to as COM1 through COM4 in the MS-DOS/Windows world. If you have an internal modem on COM4 and a serial port at COM2, you will have to change the IRQ of the modem to 2 (for obscure technical reasons, IRQ2 = IRQ 9) in order to access it from FreeBSD. If you have a multiport serial card, check the manual page for &man.sio.4; for more information on the proper values for these lines. Some video cards (notably those based on S3 chips) use IO addresses in the form of 0x*2e8, and since many cheap serial cards do not fully decode the 16-bit IO address space, they clash with these cards making the COM4 port practically unavailable. Each serial port is required to have a unique IRQ (unless you are using one of the multiport cards where shared interrupts are supported), so the default IRQs for COM3 and COM4 cannot be used. # Parallel port device ppc0 at isa? irq 7 This is the ISA-bus parallel port interface. device ppbus # Parallel port bus (required) Provides support for the parallel port bus. device lpt # Printer Support for parallel port printers. All three of the above are required to enable parallel printer support. device plip # TCP/IP over parallel This is the driver for the parallel network interface. device ppi # Parallel port interface device The general-purpose I/O (geek port) + IEEE1284 I/O. #device vpo # Requires scbus and da zip drive This is for an Iomega Zip drive. It requires scbus and da support. Best performance is achieved with ports in EPP 1.9 mode. # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (Tulip) device fxp # Intel EtherExpress PRO/100B (82557, 82558) device tx # SMC 9432TX (83c170 EPIC) device vx # 3Com 3c590, 3c595 (Vortex) device wx # Intel Gigabit Ethernet Card (Wiseman) Various PCI network card drivers. Comment out or remove any of these not present in your system. # PCI Ethernet NICs that use the common MII bus controller code. device miibus # MII bus support MII bus support is required for some PCI 10/100 Ethernet NICs, namely those which use MII-compliant transceivers or implement transceiver control interfaces that operate like an MII. Adding device miibus to the kernel config pulls in support for the generic miibus API and all of the PHY drivers, including a generic one for PHYs that are not specifically handled by an individual driver. device dc # DEC/Intel 21143 and various workalikes device rl # RealTek 8129/8139 device sf # Adaptec AIC-6915 (Starfire) device sis # Silicon Integrated Systems SiS 900/SiS 7016 device ste # Sundance ST201 (D-Link DFE-550TX) device tl # Texas Instruments ThunderLAN device vr # VIA Rhine, Rhine II device wb # Winbond W89C840F device xl # 3Com 3c90x (Boomerang, Cyclone) Drivers that use the MII bus controller code. # ISA Ethernet NICs. device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 device ex device ep # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really # exists only as a PCMCIA device, so there is no ISA attachment needed # and resources will always be dynamically assigned by the pccard code. device wi # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP # mode (the factory default). If you set the switches on your ISA # card for a manually chosen I/O address and IRQ, you must specify # those parameters here. device an # The probe order of these is presently determined by i386/isa/isa_compat.c. device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 device fe0 at isa? port 0x300 device le0 at isa? port 0x300 irq 5 iomem 0xd0000 device lnc0 at isa? port 0x280 irq 10 drq 0 device cs0 at isa? port 0x300 device sn0 at isa? port 0x300 irq 10 # requires PCCARD (PCMCIA) support to be activated #device xe0 at isa? ISA Ethernet drivers. See /usr/src/sys/i386/conf/LINT for which cards are supported by which driver. pseudo-device ether # Ethernet support ether is only needed if you have an Ethernet card. It includes generic Ethernet protocol code. pseudo-device sl 1 # Kernel SLIP sl is for SLIP support. This has been almost entirely supplanted by PPP, which is easier to set up, better suited for modem-to-modem connection, and more powerful. The number after sl specifies how many simultaneous SLIP sessions to support. pseudo-device ppp 1 # Kernel PPP This is for kernel PPP support for dial-up connections. There is also a version of PPP implemented as a userland application that uses tun and offers more flexibility and features such as demand dialing. The number after ppp specifies how many simultaneous PPP connections to support. pseudo-device tun # Packet tunnel. This is used by the userland PPP software. A number after tun specifies the number of simultaneous PPP sessions to support. See the PPP section of this book for more information. pseudo-device pty # Pseudo-ttys (telnet etc) This is a pseudo-terminal or simulated login port. It is used by incoming telnet and rlogin sessions, xterm, and some other applications such as emacs. A number after pty indicates the number of ptys to create. If you need more than the default of 16 simultaneous xterm windows and/or remote logins, be sure to increase this number accordingly, up to a maximum of 256. pseudo-device md # Memory disks Memory disk pseudo-devices. pesudo-device gif or pseudo-device gif 4 # IPv6 and IPv4 tunneling This implements IPv6 over IPv4 tunneling, IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling, and IPv6 over IPv6 tunneling. Beginning with FreeBSD 4.4 the gif device is auto-cloning, and you should use the first example (without the number after gif). Earlier versions of FreeBSD require the number. pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) This pseudo-device captures packets that are sent to it and diverts them to the IPv4/IPv6 translation daemon. # The `bpf' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! pseudo-device bpf # Berkeley packet filter This is the Berkeley Packet Filter. This pseudo-device allows network interfaces to be placed in promiscuous mode, capturing every packet on a broadcast network (e.g., an Ethernet). These packets can be captured to disk and or examined with the &man.tcpdump.1; program. The bpf pseudo-device is also used by &man.dhclient.8; to obtain the IP address of the default router (gateway) and so on. If you use DHCP, leave this uncommented. # USB support #device uhci # UHCI PCI->USB interface #device ohci # OHCI PCI->USB interface #device usb # USB Bus (required) #device ugen # Generic #device uhid # Human Interface Devices #device ukbd # Keyboard #device ulpt # Printer #device umass # Disks/Mass storage - Requires scbus and da #device ums # Mouse # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernet Support for various USB devices. For more information and additional devices supported by FreeBSD, see /usr/src/sys/i386/conf/LINT. Making Device Nodes device nodes MAKEDEV Almost every device in the kernel has a corresponding node entry in the /dev directory. These nodes look like regular files, but are actually special entries into the kernel which programs use to access the device. The shell script /dev/MAKEDEV, which is executed when you first install the operating system, creates nearly all of the device nodes supported. However, it does not create all of them, so when you add support for a new device, it pays to make sure that the appropriate entries are in this directory, and if not, add them. Here is a simple example: Suppose you add the IDE CD-ROM support to the kernel. The line to add is: device acd0 This means that you should look for some entries that start with acd0 in the /dev directory, possibly followed by a letter, such as c, or preceded by the letter r, which means a raw device. It turns out that those files are not there, so you must change to the /dev directory and type: MAKEDEV &prompt.root; sh MAKEDEV acd0 When this script finishes, you will find that there are now acd0c and racd0c entries in /dev so you know that it executed correctly. For sound cards, the following command creates the appropriate entries: &prompt.root; sh MAKEDEV snd0 When creating device nodes for devices such as sound cards, if other people have access to your machine, it may be desirable to protect the devices from outside access by adding them to the /etc/fbtab file. See &man.fbtab.5; for more information. Follow this simple procedure for any other non-GENERIC devices which do not have entries. All SCSI controllers use the same set of /dev entries, so you do not need to create these. Also, network cards and SLIP/PPP pseudo-devices do not have entries in /dev at all, so you do not have to worry about these either. If Something Goes Wrong There are five categories of trouble that can occur when building a custom kernel. They are: config fails: If the config command fails when you give it your kernel description, you have probably made a simple error somewhere. Fortunately, config will print the line number that it had trouble with, so you can quickly skip to it with vi. For example, if you see: config: line 17: syntax error You can skip to the problem in vi by typing 17G in command mode. Make sure the keyword is typed correctly, by comparing it to the GENERIC kernel or another reference. make fails: If the make command fails, it usually signals an error in your kernel description, but not severe enough for config to catch it. Again, look over your configuration, and if you still cannot resolve the problem, send mail to the &a.questions; with your kernel configuration, and it should be diagnosed very quickly. Installing the new kernel fails If the kernel compiled fine, but failed to install (the make install or make installkernel command failed), the first thing to check is if your system is running at securelevel 1 or higher (see &man.init.8;). The kernel installation tries to remove the immutable flag from your kernel and set the immutable flag on the new one. Since securelevel 1 or higher prevents unsetting the immutable flag for any files on the system, the kernel installation needs to be performed at securelevel 0 or lower. The kernel will not boot: If your new kernel does not boot, or fails to recognize your devices, do not panic! Fortunately, BSD has an excellent mechanism for recovering from incompatible kernels. Simply choose the kernel you want to boot from at the FreeBSD boot loader. You can access this when the system counts down from 10. Hit any key except for the enter key, type unload and then type boot kernel.old, or the filename of any other kernel that will boot properly. When reconfiguring a kernel, it is always a good idea to keep a kernel that is known to work on hand. After booting with a good kernel you can check over your configuration file and try to build it again. One helpful resource is the /var/log/messages file which records, among other things, all of the kernel messages from every successful boot. Also, the &man.dmesg.8; command will print the kernel messages from the current boot. If you are having trouble building a kernel, make sure to keep a GENERIC, or some other kernel that is known to work on hand as a different name that will not get erased on the next build. You cannot rely on kernel.old because when installing a new kernel, kernel.old is overwritten with the last installed kernel which may be non-functional. Also, as soon as possible, move the working kernel to the proper kernel location or commands such as &man.ps.1; will not work properly. The proper command to unlock the kernel file that make installs (in order to move another kernel back permanently) is: &prompt.root; chflags noschg /kernel If you find you cannot do this, you are probably running at a &man.securelevel.8; greater than zero. Edit kern_securelevel in /etc/rc.conf and set it to -1, then reboot. You can change it back to its previous setting when you are happy with your new kernel. And, if you want to lock your new kernel into place, or any file for that matter, so that it cannot be moved or tampered with: &prompt.root; chflags schg /kernel The kernel works, but ps does not work any more!: If you have installed a different version of the kernel from the one that the system utilities have been built with, for example, a 4.X kernel on a 3.X system, many system-status commands like &man.ps.1; and &man.vmstat.8; will not work any more. You must recompile the libkvm library as well as these utilities. This is one reason it is not normally a good idea to use a different version of the kernel from the rest of the operating system.